On 13/12/2018 09:34, Joseph Lo wrote:
> When generating the OPP table, the voltages are round down with the
> alignment from the regulator. The alignment should be applied for
> voltages look up as well.
>
> Based on the work of Penny Chiu <pchiu@xxxxxxxxxx>.
>
> Signed-off-by: Joseph Lo <josephl@xxxxxxxxxx>
> ---
> *V2:
> - s/align_volt/align_step/
> - s/reg_volt/reg_volt_id/
> ---
> drivers/clk/tegra/clk-dfll.c | 26 +++++++++++++++-----------
> 1 file changed, 15 insertions(+), 11 deletions(-)
>
> diff --git a/drivers/clk/tegra/clk-dfll.c b/drivers/clk/tegra/clk-dfll.c
> index 72e02898006c..b3668073d9b4 100644
> --- a/drivers/clk/tegra/clk-dfll.c
> +++ b/drivers/clk/tegra/clk-dfll.c
> @@ -804,17 +804,17 @@ static void dfll_init_out_if(struct tegra_dfll *td)
> static int find_lut_index_for_rate(struct tegra_dfll *td, unsigned long rate)
> {
> struct dev_pm_opp *opp;
> - int i, uv;
> + int i, align_step;
>
> opp = dev_pm_opp_find_freq_ceil(td->soc->dev, &rate);
> if (IS_ERR(opp))
> return PTR_ERR(opp);
>
> - uv = dev_pm_opp_get_voltage(opp);
> + align_step = dev_pm_opp_get_voltage(opp) / td->soc->alignment.step_uv;
> dev_pm_opp_put(opp);
>
> for (i = td->lut_bottom; i < td->lut_size; i++) {
> - if (td->lut_uv[i] >= uv)
> + if ((td->lut_uv[i] / td->soc->alignment.step_uv) >= align_step)
> return i;
> }
>
> @@ -1532,15 +1532,17 @@ static int dfll_init(struct tegra_dfll *td)
> */
> static int find_vdd_map_entry_exact(struct tegra_dfll *td, int uV)
> {
> - int i, n_voltages, reg_uV;
> + int i, n_voltages, reg_volt_id, align_step;
>
> + align_step = uV / td->soc->alignment.step_uv;
> n_voltages = regulator_count_voltages(td->vdd_reg);
> for (i = 0; i < n_voltages; i++) {
> - reg_uV = regulator_list_voltage(td->vdd_reg, i);
> - if (reg_uV < 0)
> + reg_volt_id = regulator_list_voltage(td->vdd_reg, i) /
> + td->soc->alignment.step_uv;
> + if (reg_volt_id < 0)
I don't think that this will work. If the step is say 10000 and we
return an error code greater than -10000, we will end up with 0.
> break;
>
> - if (uV == reg_uV)
> + if (align_step == reg_volt_id)
> return i;
> }
>
> @@ -1554,15 +1556,17 @@ static int find_vdd_map_entry_exact(struct tegra_dfll *td, int uV)
> * */
> static int find_vdd_map_entry_min(struct tegra_dfll *td, int uV)
> {
> - int i, n_voltages, reg_uV;
> + int i, n_voltages, reg_volt_id, align_step;
>
> + align_step = uV / td->soc->alignment.step_uv;
> n_voltages = regulator_count_voltages(td->vdd_reg);
> for (i = 0; i < n_voltages; i++) {
> - reg_uV = regulator_list_voltage(td->vdd_reg, i);
> - if (reg_uV < 0)
> + reg_volt_id = regulator_list_voltage(td->vdd_reg, i) /
> + td->soc->alignment.step_uv;
> + if (reg_volt_id < 0)
Same here.
> break;
>
> - if (uV <= reg_uV)
> + if (align_step <= reg_volt_id)
> return i;
> }
>
>
--
nvpublic
