This series is a major overhaul and adds support for the V1.1 hardware
revision of the Toradex Apalis T30 system on module.
Changes in v2:
- Clean-up PCIe controller/port status' as well.
- Also move serial UART "nvidia,tegra30-hsuart" compatible to module
level device trees.
- Also add two missing newlines.
- Also replace underscores in node names with dashes.
- Explicitly disable input of BKL1_ON as well.
- Replace underscores in node names with dashes.
- When running some more tests I realized that the reg-addr should
really be 0x3f. Fix this.
- Get rid of fake clocks simple bus as suggested by Rob.
- Replace "[PATCH 27/28] ARM: tegra: apalis_t30: fix pcie switch vendor
compatible" with "[PATCH v2 26/34] dt-bindings: add broadcom (formerly
plx technology) vendor prefix" as suggested by Stefan.
- New patch as suggested by Rob.
- New patch.
- Drop "[PATCH 01/28] ARM: tegra: apalis_t30: enable broken-hpi on emmc"
which should already be handled by the broken-hpi quirk as pointed out
by Dmitry. If I would find more eMMC parts which exhibit the issue I
will add them to the quirk as a separate patch.
- Updated V1.1 device trees with all applicable previous fixes.
Marcel Ziswiler (34):
ARM: tegra: apalis_t30: fix mmc1 cmd pull-up
ARM: tegra: apalis_t30: pull-up sd card detect pins
ARM: tegra: apalis_t30: add local-mac-address property
ARM: tegra: apalis_t30: reorder pcie properties
ARM: tegra: apalis_t30: annotate/clean-up pcie controller/port nodes
ARM: tegra: apalis_t30: reorder host1x/hdmi properties
ARM: tegra: apalis_t30: regulator clean-up
ARM: tegra: apalis_t30: add missing regulators
ARM: tegra: apalis_t30: annotate uarts and move compatible to board
ARM: tegra: apalis_t30: drop unused cami2c label
ARM: tegra: apalis_t30: white-space/newline clean-up
ARM: tegra: apalis_t30: drop unused mmc1/sd1 labels
ARM: tegra: apalis_t30: annotate mmc1/sd1
ARM: tegra: apalis_t30: move dr_mode property from phy to controller
ARM: tegra: apalis_t30: reorder backlight properties
ARM: tegra: apalis_t30: drop pwmleds
ARM: tegra: apalis_t30: pinmux clean-up
ARM: tegra: apalis_t30: add missing pinmux
ARM: tegra: apalis_t30: use proper irq-gpio for stmpe811
ARM: tegra: apalis_t30: further lm95245 temperature sensor annotation
ARM: tegra: apalis_t30: add i2c-thermtrip
ARM: tegra: apalis_t30: add proper emmc vmmc and vqmmc supplies
ARM: tegra: apalis_t30: enable emmc ddr52 mode
ARM: tegra: apalis_t30: get rid of fake clocks simple bus
ARM: tegra: apalis_t30: line break long compatible property line
dt-bindings: add broadcom (formerly plx technology) vendor prefix
ARM: tegra: apalis_t30: drop module level model and compatible
ARM: tegra: apalis_t30: drop obsolete spidev nodes
ARM: tegra: apalis_t30: hog group for pcie switch reset gpio
ARM: tegra: apalis_t30: rename hdmiddc to hdmi_ddc
ARM: tegra: apalis_t30: rename tps65911@2d, stmpe811@41 and
tps62362@60
ARM: tegra: apalis_t30: fix mcp2515 can controller interrupt polarity
ARM: tegra: apalis_t30: move hda node from carrier to module
ARM: tegra: apalis_t30: support v1.1 hardware revision
Documentation/devicetree/bindings/arm/tegra.txt | 2 +
.../devicetree/bindings/vendor-prefixes.txt | 1 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/tegra30-apalis-eval.dts | 148 +--
arch/arm/boot/dts/tegra30-apalis-v1.1-eval.dts | 266 +++++
arch/arm/boot/dts/tegra30-apalis-v1.1.dtsi | 1189 ++++++++++++++++++++
arch/arm/boot/dts/tegra30-apalis.dtsi | 705 +++++++++---
7 files changed, 2064 insertions(+), 248 deletions(-)
create mode 100644 arch/arm/boot/dts/tegra30-apalis-v1.1-eval.dts
create mode 100644 arch/arm/boot/dts/tegra30-apalis-v1.1.dtsi
--
2.14.4
