Re: [PATCH v2 00/40] Tegra SDHCI add support for HS200 and UHS signaling

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Fri, Aug 10, 2018 at 09:08:02PM +0300, Aapo Vienamo wrote:
> Hi all,
> 
> This series implements support for faster signaling modes on Tegra
> SDHCI controllers. This series consist of several parts: changes
> requried for 1.8 V signaling and pad control, pad calibration, and
> tuning. Following earlies patch sets have been merged into this
> larger set: "Tegra PMC pinctrl pad configuration", "Tegra SDHCI enable
> 1.8 V signaling on Tegar210 and Tegra186", "Tegra SDHCI update the
> padautocal procedure". Also the patches for enabling SDHCI tuning
> are added.
> 
> Changelog:
> v2:
> 	- Fix grammar in PMC device tree bindings docs
> 	- Remove a stray line from tegra sdhci bindings
> 	- Cosmetic changes to PMC pinctrl driver
> 	- Fix a typo in "soc/tegra: pmc: Implement
> 	  tegra_io_pad_is_powered()" commit message
> 	- Declare mask and value on the same line in
> 	  tegra_io_pad_is_powered()
> 	- Move the call to tegra_sdhci_is_pad_and_regulator_valid() to
> 	  inside the if condition in tegra_sdhci_reset()
> 	- Use usleep_range() in tegra_sdhci_configure_cal_pad()
> 	- Move sdhci_writel() out of the enable if-else body in
> 	  tegra_sdhci_configure_cal_pad()
> 	- Add a delay before starting polling in
> 	  tegra_sdhci_pad_autocalib()
> 	- Use usleep_range() in tegra_sdhci_set_tap()
> 	- Rename orig_enabled to status in
> 	  tegra_sdhci_configure_card_clk()
> 	- Fix if condition wrapping alignment in tegra_sdhci_set_tap()
> 
> v1:
> 	- Probe the regulator voltage capabilities to determine whether pinctrl
> 	  is needed in tegra_sdhci_r eset
> 	- Don't remove tegra_sdhci_voltage_switch()
> 	- Use dev_warn() in tegra_sdhci_init_pinctrl_info()
> 	- Don't change start_signal_voltage_switch callback if pinctrl info
> 	  invalid
> 	- Only call udelay(1) on enable in tegra_sdhci_configure_cal_pad()
> 	- Add nvidia, prefix to pad autocal offset dt props in the example
> 
> See the original patch sets for earlier changelogs.
> 
> Aapo Vienamo (40):
>   dt-bindings: Add Tegra PMC pad configuration bindings
>   dt-bindings: mmc: tegra: Add pad voltage control properties
>   dt-bindings: Add Tegra SDHCI pad pdpu offset bindings
>   dt-bindings: mmc: Add Tegra SDHCI sampling trimmer values
>   soc/tegra: pmc: Fix pad voltage configuration for Tegra186
>   soc/tegra: pmc: Factor out DPD register bit calculation
>   soc/tegra: pmc: Implement tegra_io_pad_is_powered()
>   soc/tegra: pmc: Use X macro to generate IO pad tables
>   soc/tegra: pmc: Remove public pad voltage APIs
>   soc/tegra: pmc: Implement pad configuration via pinctrl
>   mmc: sdhci: Add a quirk to skip clearing the transfer mode register on
>     tuning
>   mmc: tegra: Reconfigure pad voltages during voltage switching
>   mmc: tegra: Poll for calibration completion
>   mmc: tegra: Set calibration pad voltage reference
>   mmc: tegra: Power on the calibration pad
>   mmc: tegra: Disable card clock during pad calibration
>   mmc: tegra: Program pad autocal offsets from dt
>   mmc: tegra: Perform pad calibration after voltage switch
>   mmc: tegra: Enable pad calibration on Tegra210 and Tegra186
>   mmc: tegra: Add a workaround for tap value change glitch
>   mmc: tegra: Parse default trim and tap from dt
>   mmc: tegra: Configure default tap values
>   mmc: tegra: Configure default trim value on reset
>   mmc: tegra: Use standard SDHCI tuning on Tegra210 and Tegra186
>   mmc: sdhci: Add a quirk to disable card clock during tuning
>   mmc: tegra: Enable workaround for tuning transfer mode bug
>   mmc: tegra: Set SDHCI_QUIRK2_TUNE_DIS_CARD_CLK on Tegra210
>   mmc: tegra: Enable UHS and HS200 modes for Tegra210
>   mmc: tegra: Enable UHS and HS200 modes for Tegra186
>   arm64: dts: Add Tegra210 sdmmc pinctrl voltage states
>   arm64: dts: Add Tegra186 sdmmc pinctrl voltage states
>   arm64: dts: tegra210-p2180: Allow ldo2 to go down to 1.8 V
>   arm64: dts: tegra210-p2180: Correct sdmmc4 vqmmc-supply
>   arm64: dts: tegra210-p2597: Remove no-1-8-v from sdmmc1
>   arm64: dts: tegra186: Add sdmmc pad auto calibration offsets
>   arm64: dts: tegra210: Add sdmmc pad auto calibration offsets
>   arm64: dts: tegra210: Add SDHCI tap and trim values
>   arm64: dts: tegra186: Add SDHCI tap and trim values
>   arm64: dts: tegra186: Assign clocks for sdmmc1 and sdmmc4
>   arm64: dts: tegra210: Assign clocks for sdmmc1 and sdmmc4
> 
>  .../bindings/arm/tegra/nvidia,tegra186-pmc.txt     |  93 ++++
>  .../bindings/arm/tegra/nvidia,tegra20-pmc.txt      | 103 ++++
>  .../bindings/mmc/nvidia,tegra20-sdhci.txt          |  68 +++
>  arch/arm64/boot/dts/nvidia/tegra186.dtsi           |  74 +++
>  arch/arm64/boot/dts/nvidia/tegra210-p2180.dtsi     |  12 +-
>  arch/arm64/boot/dts/nvidia/tegra210-p2597.dtsi     |   1 -
>  arch/arm64/boot/dts/nvidia/tegra210.dtsi           |  55 ++
>  drivers/mmc/host/sdhci-tegra.c                     | 556 +++++++++++++++++++--
>  drivers/mmc/host/sdhci.c                           |  21 +
>  drivers/mmc/host/sdhci.h                           |   4 +
>  drivers/soc/tegra/pmc.c                            | 511 ++++++++++++++-----
>  include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h |  18 +
>  include/soc/tegra/pmc.h                            |  20 +-
>  13 files changed, 1324 insertions(+), 212 deletions(-)
>  create mode 100644 include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h

Adrian,

these patches are also a prerequisite for the UHS signalling changes in
the other two series that Aapo posted. It'd be great if you could take a
quick look and weigh in.

Thanks,
Thierry

Attachment: signature.asc
Description: PGP signature


[Index of Archives]     [ARM Kernel]     [Linux ARM]     [Linux ARM MSM]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux