On Wed, Aug 01, 2018 at 07:31:51PM +0300, Aapo Vienamo wrote:
> Document the PMC pinctrl bindings for pad power state and signaling
> voltage configuration. Both nvidia,tegra186-pmc.txt and
> nvidia,tegra20-pmc.txt are modified as they both cover SoC generations
> for which these bindings apply.
>
> Add a header defining Tegra PMC pad voltage configurations.
>
> Signed-off-by: Aapo Vienamo <avienamo@xxxxxxxxxx>
> Acked-by: Jon Hunter <jonathanh@xxxxxxxxxx>
> Reviewed-by: Rob Herring <robh@xxxxxxxxxx>
> ---
> .../bindings/arm/tegra/nvidia,tegra186-pmc.txt | 92 ++++++++++++++++++
> .../bindings/arm/tegra/nvidia,tegra20-pmc.txt | 103 +++++++++++++++++++++
> include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h | 18 ++++
> 3 files changed, 213 insertions(+)
> create mode 100644 include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h
>
> diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt
> index 5a3bf7c..d7fed4d 100644
> --- a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt
> +++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra186-pmc.txt
> @@ -34,3 +34,95 @@ Board DTS:
> pmc@c360000 {
> nvidia,invert-interrupt;
> };
> +
> +== Pad Control ==
> +
> +On Tegra SoCs a pad is a set of pins which are configured as a group.
> +The pin grouping is a fixed attribute of the hardware. The PMC can be
> +used to set pad power state and signaling voltage. A pad can be either
> +in active or power down mode. The support for power state and signaling
> +voltage configuration varies depending on the pad in question. 3.3 V and
> +1.8 V signaling voltages are supported on pins where software
> +controllable signaling voltage switching is available.
> +
> +Pad configurations are described is with pin configuration nodes which
The "is" in the middle there seems to be left-over from a previous
formulation of the sentence.
> +are placed under the pmc node and they are referred to by the pinctrl
> +client properties. For more information see
> +Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt.
> +
> +Following pads are present on Tegra186:
"The following pads..."
> +csia csib dsi mipi-bias
> +pex-clk-bias pex-clk3 pex-clk2 pex-clk1
> +usb0 usb1 usb2 usb-bias
> +uart audio hsic dbg
> +hdmi-dp0 hdmi-dp1 pex-cntrl sdmmc2-hv
> +sdmmc4 cam dsib dsic
> +dsid csic csid csie
> +dsif spi ufs dmic-hv
> +edp sdmmc1-hv sdmmc3-hv conn
> +audio-hv ao-hv
> +
> +Required pin configuration properties:
> + - pins: Must contain name of the pad(s) to be configured.
"the name". Also, I'm assuming that this can take a list of names, so
perhaps this should read:
- pins: A list of strings, each of which contains the name of a pad
to be configured.
> +
> +Optional pin configuration properties:
> + - low-power-enable: Configure the pad into power down mode
> + - low-power-disable: Configure the pad into active mode
Do we need both of these? low-power could be a boolean property to mean
that the pad(s) should be configured in power down mode. If absent it
would mean that the pad(s) should be configured in normal mode. The only
reason why I can think of them to have to be separate is if we want to
define a configuration where the power mode is not touched. But is that
really something we need or want?
> + - power-source: Must contain either TEGRA_IO_PAD_VOLTAGE_1V8 or
> + TEGRA_IO_PAD_VOLTAGE_3V3 to select between signaling voltages.
> + The values are defined in
> + include/dt-bindings/pinctrl/pinctrl-tegra-io-pad.h.
Why is this called "power-source"? This defines the signaling voltage of
the pad, so why not something like "power-level", or "voltage", or
"output-voltage"?
Or is this because it is a mux that will internally select either a
1.8 V or a 3.3 V source? In which case I guess this is okay. Perhaps
give some explanation of the mechanics of the underlying hardware to
make this more obvious.
> +
> +Note: The power state can be configured on all of the above pads except
> + for ao-hv. Following pads have software configurable signaling
> + voltages: sdmmc2-hv, dmic-hv, sdmmc1-hv, sdmmc3-hv, audio-hv,
> + ao-hv.
> +
> +Pad configuration state example:
> + pmc: pmc@7000e400 {
> + compatible = "nvidia,tegra186-pmc";
> + reg = <0 0x0c360000 0 0x10000>,
> + <0 0x0c370000 0 0x10000>,
> + <0 0x0c380000 0 0x10000>,
> + <0 0x0c390000 0 0x10000>;
> + reg-names = "pmc", "wake", "aotag", "scratch";
> +
> + ...
> +
> + sdmmc1_3v3: sdmmc1-3v3 {
> + pins = "sdmmc1-hv";
> + power-source = <TEGRA_IO_PAD_VOLTAGE_3V3>;
> + };
> +
> + sdmmc1_1v8: sdmmc1-1v8 {
> + pins = "sdmmc1-hv";
> + power-source = <TEGRA_IO_PAD_VOLTAGE_1V8>;
> + };
Wouldn't these be implicitly low-power-disable? What if these are off by
default? Selecting these states would change the power source but keep
them in power down, no? Don't we want something like the below instead?
sdmmc1_3v3: sdmmc1-3v3 {
pins = "sdmmc1-hv";
power-source = <TEGRA_IO_PAD_VOLTAGE_3V3>;
/* low-power-disable implied here */
};
sdmmc1_1v8: sdmmc1-1v8 {
pins = "sdmmc1-hv";
power-source = <TEGRA_IO_PAD_VOLTAGE_1V8>;
/* low-power-disable implied here */
};
sdmmc1_off: sdmmc1-off {
pins = "sdmmc1-hv";
low-power;
};
That would allow the SDHCI driver to select between the two signaling
modes and a separate state for powering down the pad.
> +
> + hdmi_off: hdmi-off {
> + pins = "hdmi";
> + low-power-enable;
> + }
> +
> + hdmi_on: hdmi-on {
> + pins = "hdmi";
> + low-power-disable;
> + }
These would similarily become:
hdmi_off: hdmi-off {
pins = "hdmi";
low-power;
};
hdmi_on: hdmi-on {
pins = "hdmi";
};
> diff --git a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt
> index a74b37b..5363b90 100644
> --- a/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt
> +++ b/Documentation/devicetree/bindings/arm/tegra/nvidia,tegra20-pmc.txt
> @@ -195,3 +195,106 @@ Example:
> power-domains = <&pd_audio>;
> ...
> };
> +
> +== Pad Control ==
> +
> +On Tegra SoCs a pad is a set of pins which are configured as a group.
> +The pin grouping is a fixed attribute of the hardware. The PMC can be
> +used to set pad power state and signaling voltage. A pad can be either
> +in active or power down mode. The support for power state and signaling
> +voltage configuration varies depending on the pad in question. 3.3 V and
> +1.8 V signaling voltages are supported on pins where software
> +controllable signaling voltage switching is available.
> +
> +The pad configuration state nodes are placed under the pmc node and they
> +are referred to by the pinctrl client properties. For more information
> +see Documentation/devicetree/bindings/pinctrl/pinctrl-bindings.txt.
> +The pad name should be used as the value of the pins property in pin
> +configuration nodes.
> +
> +Following pads are present on Tegra124 and Tegra132:
> +audio bb cam comp
> +csia csb cse dsi
> +dsib dsic dsid hdmi
> +hsic hv lvds mipi-bias
> +nand pex-bias pex-clk1 pex-clk2
> +pex-cntrl sdmmc1 sdmmc3 sdmmc4
> +sys_ddc uart usb0 usb1
> +usb2 usb_bias
> +
> +Following pads are present on Tegra210:
> +audio audio-hv cam csia
> +csib csic csid csie
> +csif dbg debug-nonao dmic
> +dp dsi dsib dsic
> +dsid emmc emmc2 gpio
> +hdmi hsic lvds mipi-bias
> +pex-bias pex-clk1 pex-clk2 pex-cntrl
> +sdmmc1 sdmmc3 spi spi-hv
> +uart usb0 usb1 usb2
> +usb3 usb-bias
What about chips prior to Tegra124?
Thierry
Attachment:
signature.asc
Description: PGP signature
