On 07/26/2018 10:47 AM, Stefan Agner wrote:
On 26.07.2018 15:56, Peter Geis wrote:
On 07/12/2018 03:39 AM, Stefan Agner wrote:
It seems that SD3.0 advertisement needs to be set for higher eMMC
speed modes (namely DDR52) as well. The TRM states that the SD3.0
advertisement bit should be set for all controller instances, even
for those not supporting UHS-I mode...
When specifying vqmmc-supply as a fixed 1.8V regulator on a Tegra
SD/MMC instance which is connected to a eMMC device, the stack
enables SD3.0. However, enabling it has consequences: If SDHCI 3.0
support is advertised the stack enables Auto-CMD23. Unfortunately
Auto-CMD23 seems not to work well with Tegra 3 currently. It leads
to regular warnings:
mmc2: Got command interrupt 0x00010000 even though no command operation was in progress.
It is not entirely clear why those errors happens. It seems that
a Linux 3.1 based downstream kernel which has Auto-CMD23 support
does not show those warnings.
Use quirk SDHCI_QUIRK2_ACMD23_BROKEN to prevent Auto-CMD23 being
used for now. With this the eMMC works stable on high-speed mode
while still announcing SD3.0.
This allows to use mmc-ddr-1_8v to enables DDR52 mode. In DDR52
mode read speed improves from about 42MiB/s to 72MiB/s on an
Apalis T30.
Signed-off-by: Stefan Agner <stefan@xxxxxxxx>
---
drivers/mmc/host/sdhci-tegra.c | 10 +++++++++-
1 file changed, 9 insertions(+), 1 deletion(-)
diff --git a/drivers/mmc/host/sdhci-tegra.c b/drivers/mmc/host/sdhci-tegra.c
index 888a1ad511db..11c0b2069c7c 100644
--- a/drivers/mmc/host/sdhci-tegra.c
+++ b/drivers/mmc/host/sdhci-tegra.c
@@ -336,7 +336,15 @@ static const struct sdhci_pltfm_data sdhci_tegra30_pdata = {
SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC |
SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN,
.quirks2 = SDHCI_QUIRK2_PRESET_VALUE_BROKEN |
- SDHCI_QUIRK2_BROKEN_HS200,
+ SDHCI_QUIRK2_BROKEN_HS200 |
+ /*
+ * Auto-CMD23 leads to "Got command interrupt 0x00010000 even
+ * though no command operation was in progress."
+ *
+ * The exact reason is unknown, as the same hardware seems
+ * to support Auto CMD23 on a downstream 3.1 kernel.
+ */
+ SDHCI_QUIRK2_ACMD23_BROKEN,
.ops = &tegra_sdhci_ops,
};
I finally got around to testing this on the Ouya (Tegra 3).
Thanks for testing!
I found that the "Got command interrupt 0x00010000 even though no
command operation was in progress." error occurred when the interface
is unstable.
I've had a lot of problems with sdmmc4 stability on the Ouya above 34
Mhz, probably due to the fact that they are using the internal cmd and
clock pull-up resistors, against the TRM's instruction.
At 39Mhz, I saw the error this patch corrects.
With the patch, the error went away, but the interface is still
unstable under load.
How does this instability manifest exactly?
At the very edge of stability, you see write errors under heavy load.
As clock rate increases, the write errors occur more frequently.
At a certain point, you start getting read errors.
Following that you get constant io errors during card probing.
Eventually the emmc will fail to initialize, with errors 87 or 110.
I've been tweaking the pull up/down values to try and improve the
stability, but without access to anything but the TRM it's a lot of
trial and error.
Lowering down to 32Mhz, without the patch there are no errors.
So the patch does not make it less stable right?
No, it did not affect stability.
Although I'd conduct some performance testing to check for degradation.
Of course I'm nowhere near the limits of the controller, so it is
doubtful I'd see a hit.
--
Stefan
--
To unsubscribe from this list: send the line "unsubscribe linux-tegra" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
