On Tue, Feb 06, 2018 at 06:34:08PM +0200, Peter De Schrijver wrote:
> Add new properties to configure the DFLL PWM regulator support. Also
> add an example and make the I2C clock only required when I2C support is
> used.
>
> Signed-off-by: Peter De Schrijver <pdeschrijver@xxxxxxxxxx>
> ---
> .../bindings/clock/nvidia,tegra124-dfll.txt | 76 +++++++++++++++++++++-
> 1 file changed, 74 insertions(+), 2 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt b/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt
> index dff236f..a4903f7 100644
> --- a/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt
> +++ b/Documentation/devicetree/bindings/clock/nvidia,tegra124-dfll.txt
> @@ -23,7 +23,8 @@ Required properties:
> - clock-names: Must include the following entries:
> - soc: Clock source for the DFLL control logic.
> - ref: The closed loop reference clock
> - - i2c: Clock source for the integrated I2C master.
> + - i2c: Clock source for the integrated I2C master (only required when
> + using I2C mode).
> - resets: Must contain an entry for each entry in reset-names.
> See ../reset/reset.txt for details.
> - reset-names: Must include the following entries:
> @@ -45,10 +46,28 @@ Required properties for the control loop parameters:
> Optional properties for the control loop parameters:
> - nvidia,cg-scale: Boolean value, see the field DFLL_PARAMS_CG_SCALE in the TRM.
>
> +Optional properties for mode selection:
> +- nvidia,pwm-to-pmic: Use PWM to control regulator rather then I2C.
> +
> Required properties for I2C mode:
> - nvidia,i2c-fs-rate: I2C transfer rate, if using full speed mode.
>
> -Example:
> +Required properties for PWM mode:
> +- nvidia,pwm-period: period of PWM square wave in us.
Add standard unit suffix.
> +- nvidia,init-uv: Regulator voltage in uV when PWM control is disabled.
> +- nvidia,align-offset-uv: Regulator voltage in uV when PWM control is enabled
> + and PWM output is low.
> +- nvidia,align-step-uv: Voltage increase in uV corresponding to a 1/33th
Use the standard unit suffix, not a custom one. See property-units.txt.
> + increase in duty cycle. Eg the voltage for 2/33th duty
> + cycle would be:
> + nvidia,align-offset-uv + nvidia,align-step-uv * 2.
> +- pinctrl-0: I/O pad configuration when PWM control is enabled.
> +- pinctrl-1: I/O pad configuration when PWM control is disabled.
> +- pinctrl-names: must include the following entries:
> + - dvfs_pwm_enable: I/O pad configuration when PWM control is enabled.
> + - dvfs_pwm_disable: I/O pad configuration when PWM control is disabled.
> +
> +Example for I2C:
>
> clock@70110000 {
> compatible = "nvidia,tegra124-dfll";
> @@ -76,3 +95,56 @@ clock@70110000 {
>
> nvidia,i2c-fs-rate = <400000>;
> };
> +
> +Example for PWM:
> +
> +clock@70110000 {
> + compatible = "nvidia,tegra124-dfll";
> + reg = <0 0x70110000 0 0x100>, /* DFLL control */
> + <0 0x70110000 0 0x100>, /* I2C output control */
> + <0 0x70110100 0 0x100>, /* Integrated I2C controller */
> + <0 0x70110200 0 0x100>; /* Look-up table RAM */
> + interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&tegra_car TEGRA210_CLK_DFLL_SOC>,
> + <&tegra_car TEGRA210_CLK_DFLL_REF>;
> + clock-names = "soc", "ref";
> + resets = <&tegra_car TEGRA124_RST_DFLL_DVCO>;
> + reset-names = "dvco";
> + #clock-cells = <0>;
> + clock-output-names = "dfllCPU_out";
> + nvidia,pwm-to-pmic;
> + nvidia,init-uv = <1000000>;
> + nvidia,align-step-uv = <19200>; /* 19.2mV */
> + nvidia,align-offset-uv = <708000>; /* 708mV */
> + nvidia,sample-rate = <25000>;
> + nvidia,droop-ctrl = <0x00000f00>;
> + nvidia,force-mode = <1>;
> + nvidia,cf = <6>;
> + nvidia,ci = <0>;
> + nvidia,cg = <2>;
> + nvidia,idle-override;
> + nvidia,one-shot-calibrate;
> + nvidia,pwm-period = <2500>; /* 2.5us */
> + pinctrl-names = "dvfs_pwm_enable", "dvfs_pwm_disable";
> + pinctrl-0 = <&dvfs_pwm_active_state>;
> + pinctrl-1 = <&dvfs_pwm_inactive_state>;
> +};
> +
> +/* pinmux nodes added for completeness. Binding doc can be found in:
> + * Documentation/devicetree/bindings/pinctrl/nvidia,tegra210-pinmux.txt
> + */
> +
> +pinmux: pinmux@700008d4 {
> + dvfs_pwm_active_state: dvfs_pwm_active {
> + dvfs_pwm_pbb1 {
> + nvidia,pins = "dvfs_pwm_pbb1";
> + nvidia,tristate = <TEGRA_PIN_DISABLE>;
> + };
> + };
> + dvfs_pwm_inactive_state: dvfs_pwm_inactive {
> + dvfs_pwm_pbb1 {
> + nvidia,pins = "dvfs_pwm_pbb1";
> + nvidia,tristate = <TEGRA_PIN_ENABLE>;
> + };
> + };
> +};
> --
> 1.9.1
>
--
To unsubscribe from this list: send the line "unsubscribe linux-tegra" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
