On 24.05.2017 08:44, Preetham Chandru wrote:
-----Original Message-----
From: Mikko Perttunen [mailto:cyndis@xxxxxxxx]
Sent: Sunday, May 14, 2017 4:49 PM
To: Preetham Chandru <pchandru@xxxxxxxxxx>; thierry.reding@xxxxxxxxx;
tj@xxxxxxxxxx
Cc: tegra@xxxxxxxxxxxxxxx; linux-ide@xxxxxxxxxxxxxxx; Laxman Dewangan
<ldewangan@xxxxxxxxxx>; preetham260@xxxxxxxxx; Venu Byravarasu
<vbyravarasu@xxxxxxxxxx>; Pavan Kunapuli <pkunapuli@xxxxxxxxxx>; linux-
tegra@xxxxxxxxxxxxxxx
Subject: Re: [PATCH V3 1/3] ata: ahci_tegra: Add AHCI support for tegra210
On 05/12/2017 12:55 PM, Preetham Chandru wrote:
+CC linux-tegra@xxxxxxxxxxxxxxx
-----Original Message-----
From: Preetham Chandru
Sent: Friday, May 12, 2017 3:04 PM
To: thierry.reding@xxxxxxxxx; tj@xxxxxxxxxx
Cc: tegra@xxxxxxxxxxxxxxx; linux-ide@xxxxxxxxxxxxxxx; Laxman Dewangan
<ldewangan@xxxxxxxxxx>; preetham260@xxxxxxxxx; Venu Byravarasu
<vbyravarasu@xxxxxxxxxx>; Pavan Kunapuli <pkunapuli@xxxxxxxxxx>;
Preetham Chandru <pchandru@xxxxxxxxxx>
Subject: [PATCH V3 1/3] ata: ahci_tegra: Add AHCI support for
tegra210
From: Preetham Chandru R <pchandru@xxxxxxxxxx>
1. Move tegra124 specifics to tegra124_ahci_init.
2. Separate the regulators needed for tegra124 and tegra210.
3. Disable DIPM and Devslp for t210 and t124 as there are known
issues
Signed-off-by: Preetham Chandru R <pchandru@xxxxxxxxxx>
---
v3:
* Remove inline functions for read/write and modify to SATA, SATA
Config and SATA Aux registers.
* Add code to disable DIPM and DevSlp for t210 and t124
v2:
* Fix indentation issues
* Move the change to disable DIPM, HIPM, DevSlp, partial, slumber
and NCQ into a separate patch
---
drivers/ata/ahci_tegra.c | 377
++++++++++++++++++++++++++++++++++++-------
----
1 file changed, 293 insertions(+), 84 deletions(-)
diff --git a/drivers/ata/ahci_tegra.c b/drivers/ata/ahci_tegra.c
index
3a62eb2..cd581a6 100644
--- a/drivers/ata/ahci_tegra.c
+++ b/drivers/ata/ahci_tegra.c
@@ -34,7 +34,8 @@
#define DRV_NAME "tegra-ahci"
#define SATA_CONFIGURATION_0 0x180
-#define SATA_CONFIGURATION_EN_FPCI BIT(0)
+#define SATA_CONFIGURATION_0_EN_FPCI BIT(0)
+#define SATA_CONFIGURATION_0_CLK_OVERRIDE BIT(31)
#define SCFG_OFFSET 0x1000
@@ -45,17 +46,55 @@
#define T_SATA0_CFG_1_SERR BIT(8)
#define T_SATA0_CFG_9 0x24
-#define T_SATA0_CFG_9_BASE_ADDRESS_SHIFT 13
+#define T_SATA0_CFG_9_BASE_ADDRESS 0x40020000
#define SATA_FPCI_BAR5 0x94
-#define SATA_FPCI_BAR5_START_SHIFT 4
+#define SATA_FPCI_BAR5_START_MASK (0xfffffff << 4)
+#define SATA_FPCI_BAR5_START (0x0040020 <<
4)
+#define SATA_FPCI_BAR5_ACCESS_TYPE (0x1)
#define SATA_INTR_MASK 0x188
#define SATA_INTR_MASK_IP_INT_MASK BIT(16)
+#define T_SATA0_CFG_35 0x94
+#define T_SATA0_CFG_35_IDP_INDEX_MASK (0x7ff
<< 2)
+#define T_SATA0_CFG_35_IDP_INDEX (0x2a << 2)
+
+#define T_SATA0_AHCI_IDP1 0x98
+#define T_SATA0_AHCI_IDP1_DATA (0x400040)
+
+#define T_SATA0_CFG_PHY_1 0x12c
+#define T_SATA0_CFG_PHY_1_PADS_IDDQ_EN BIT(23)
+#define T_SATA0_CFG_PHY_1_PAD_PLL_IDDQ_EN BIT(22)
+
+#define T_SATA0_NVOOB 0x114
+#define T_SATA0_NVOOB_COMMA_CNT_MASK (0xff << 16)
+#define T_SATA0_NVOOB_COMMA_CNT (0x07 << 16)
+#define T_SATA0_NVOOB_SQUELCH_FILTER_MODE_MASK (0x3 << 24)
+#define T_SATA0_NVOOB_SQUELCH_FILTER_MODE (0x1 << 24)
+#define T_SATA0_NVOOB_SQUELCH_FILTER_LENGTH_MASK (0x3 << 26)
+#define T_SATA0_NVOOB_SQUELCH_FILTER_LENGTH (0x3 << 26)
+
+#define T_SATA_CFG_PHY_0 0x120
+#define T_SATA_CFG_PHY_0_USE_7BIT_ALIGN_DET_FOR_SPD BIT(11)
+#define T_SATA_CFG_PHY_0_MASK_SQUELCH BIT(24)
+
+#define T_SATA0_CFG2NVOOB_2 0x134
+#define T_SATA0_CFG2NVOOB_2_COMWAKE_IDLE_CNT_LOW_MASK
(0x1ff
<< 18)
+#define T_SATA0_CFG2NVOOB_2_COMWAKE_IDLE_CNT_LOW (0xc <<
18)
+
#define T_SATA0_AHCI_HBA_CAP_BKDR 0x300
+#define T_SATA0_AHCI_HBA_CAP_BKDR_PARTIAL_ST_CAP BIT(13)
+#define T_SATA0_AHCI_HBA_CAP_BKDR_SLUMBER_ST_CAP BIT(14)
+#define T_SATA0_AHCI_HBA_CAP_BKDR_SALP BIT(26)
+#define T_SATA0_AHCI_HBA_CAP_BKDR_SUPP_PM BIT(17)
+#define T_SATA0_AHCI_HBA_CAP_BKDR_SNCQ BIT(30)
#define T_SATA0_BKDOOR_CC 0x4a4
+#define T_SATA0_BKDOOR_CC_CLASS_CODE_MASK (0xffff << 16)
+#define T_SATA0_BKDOOR_CC_CLASS_CODE
(0x0106 << 16)
+#define T_SATA0_BKDOOR_CC_PROG_IF_MASK (0xff <<
8)
+#define T_SATA0_BKDOOR_CC_PROG_IF (0x01 << 8)
#define T_SATA0_CFG_SATA 0x54c
#define T_SATA0_CFG_SATA_BACKDOOR_PROG_IF_EN BIT(12)
@@ -82,9 +121,35 @@
#define T_SATA0_CHX_PHY_CTRL11 0x6d0
#define T_SATA0_CHX_PHY_CTRL11_GEN2_RX_EQ (0x2800 << 16)
+#define T_SATA0_CHX_PHY_CTRL17_0 0x6e8
+#define T_SATA0_CHX_PHY_CTRL17_0_RX_EQ_CTRL_L_GEN1
0x55010000
+#define T_SATA0_CHX_PHY_CTRL18_0 0x6ec
+#define T_SATA0_CHX_PHY_CTRL18_0_RX_EQ_CTRL_L_GEN2
0x55010000
+#define T_SATA0_CHX_PHY_CTRL20_0 0x6f4
+#define T_SATA0_CHX_PHY_CTRL20_0_RX_EQ_CTRL_H_GEN1 0x1
+#define T_SATA0_CHX_PHY_CTRL21_0 0x6f8
+#define T_SATA0_CHX_PHY_CTRL21_0_RX_EQ_CTRL_H_GEN2 0x1
+
+/* AUX Registers */
+#define SATA_AUX_MISC_CNTL_1_0 0x8
+#define SATA_AUX_MISC_CNTL_1_0_DEVSLP_OVERRIDE BIT(17)
+#define SATA_AUX_MISC_CNTL_1_0_SDS_SUPPORT BIT(13)
+#define SATA_AUX_MISC_CNTL_1_0_DESO_SUPPORT BIT(15)
+
+#define SATA_AUX_RX_STAT_INT_0 0xc
+#define SATA_AUX_RX_STAT_INT_0_SATA_DEVSLP BIT(7)
+
+#define SATA_AUX_SPARE_CFG0_0 0x18
+#define SATA_AUX_SPARE_CFG0_0_MDAT_TIMER_AFTER_PG_VALID BIT(14)
+
#define FUSE_SATA_CALIB 0x124
#define FUSE_SATA_CALIB_MASK 0x3
+enum {
+ NO_DEVSLP = (1 << 0),
+ NO_DIPM = (1 << 1),
+};
+
struct sata_pad_calibration {
u8 gen1_tx_amp;
u8 gen1_tx_peak;
@@ -99,15 +164,89 @@ static const struct sata_pad_calibration
tegra124_pad_calibration[] = {
{0x14, 0x0e, 0x1a, 0x0e},
};
+struct tegra_ahci_ops {
+ int (*init)(struct ahci_host_priv *); };
+
+struct tegra_ahci_soc {
+ const char *const *supply_names;
+ u32 num_supplies;
+ u32 quirks;
+ struct tegra_ahci_ops ops;
+};
+
struct tegra_ahci_priv {
struct platform_device *pdev;
void __iomem *sata_regs;
+ void __iomem *sata_aux_regs;
struct reset_control *sata_rst;
struct reset_control *sata_oob_rst;
struct reset_control *sata_cold_rst;
/* Needs special handling, cannot use ahci_platform */
struct clk *sata_clk;
- struct regulator_bulk_data supplies[5];
+ struct regulator_bulk_data *supplies;
+ struct tegra_ahci_soc *soc_data;
+};
+
+static const char *const tegra124_supply_names[] = {
+ "avdd", "hvdd", "vddio", "target-5v", "target-12v"
+};
+
+static int tegra124_ahci_init(struct ahci_host_priv *hpriv) {
+ struct tegra_ahci_priv *tegra = hpriv->plat_data;
+ struct sata_pad_calibration calib;
+ int ret;
+ u32 val;
+
+ /* Pad calibration */
+ ret = tegra_fuse_readl(FUSE_SATA_CALIB, &val);
+ if (ret)
+ return ret;
+
+ calib = tegra124_pad_calibration[val & FUSE_SATA_CALIB_MASK];
+
+ writel(BIT(0), tegra->sata_regs + SCFG_OFFSET + T_SATA0_INDEX);
+
+ val = readl(tegra->sata_regs +
+ SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL1_GEN1);
+ val &= ~T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_MASK;
+ val &= ~T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_MASK;
+ val |= calib.gen1_tx_amp <<
T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_SHIFT;
+ val |= calib.gen1_tx_peak <<
T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_SHIFT;
+ writel(val, tegra->sata_regs + SCFG_OFFSET +
+ T_SATA0_CHX_PHY_CTRL1_GEN1);
+
+ val = readl(tegra->sata_regs +
+ SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL1_GEN2);
+ val &= ~T_SATA0_CHX_PHY_CTRL1_GEN2_TX_AMP_MASK;
+ val &= ~T_SATA0_CHX_PHY_CTRL1_GEN2_TX_PEAK_MASK;
+ val |= calib.gen2_tx_amp <<
T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_SHIFT;
+ val |= calib.gen2_tx_peak <<
T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_SHIFT;
+ writel(val, tegra->sata_regs + SCFG_OFFSET +
+ T_SATA0_CHX_PHY_CTRL1_GEN2);
+
+ writel(T_SATA0_CHX_PHY_CTRL11_GEN2_RX_EQ,
+ tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL11);
+ writel(T_SATA0_CHX_PHY_CTRL2_CDR_CNTL_GEN1,
+ tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL2);
+
+ writel(0, tegra->sata_regs + SCFG_OFFSET + T_SATA0_INDEX);
+
+ return 0;
+}
+
+static const struct tegra_ahci_soc tegra124_ahci_soc_data = {
+ .supply_names = tegra124_supply_names,
+ .num_supplies = ARRAY_SIZE(tegra124_supply_names),
+ .quirks = NO_DIPM | NO_DEVSLP,
+ .ops = {
+ .init = tegra124_ahci_init,
+ },
Indent this "}," one tab less (i.e. to same level as '.ops')
Okay.
+};
+
+static const struct tegra_ahci_soc tegra210_ahci_soc_data = {
+ .quirks = NO_DIPM | NO_DEVSLP,
};
static int tegra_ahci_power_on(struct ahci_host_priv *hpriv) @@
-115,7 +254,7 @@ static int tegra_ahci_power_on(struct ahci_host_priv
*hpriv)
struct tegra_ahci_priv *tegra = hpriv->plat_data;
int ret;
- ret = regulator_bulk_enable(ARRAY_SIZE(tegra->supplies),
+ ret = regulator_bulk_enable(tegra->soc_data->num_supplies,
tegra->supplies);
if (ret)
return ret;
@@ -144,8 +283,7 @@ static int tegra_ahci_power_on(struct
ahci_host_priv
*hpriv)
tegra_powergate_power_off(TEGRA_POWERGATE_SATA);
disable_regulators:
- regulator_bulk_disable(ARRAY_SIZE(tegra->supplies), tegra->supplies);
-
+ regulator_bulk_disable(tegra->soc_data->num_supplies,
+tegra->supplies);
Indent this.
This seems to be issue with my outlook. I don't see this issue
when I sent first using git send-email. Will take care of this.
return ret;
}
@@ -162,97 +300,137 @@ static void tegra_ahci_power_off(struct
ahci_host_priv *hpriv)
clk_disable_unprepare(tegra->sata_clk);
tegra_powergate_power_off(TEGRA_POWERGATE_SATA);
- regulator_bulk_disable(ARRAY_SIZE(tegra->supplies), tegra->supplies);
+ regulator_bulk_disable(tegra->soc_data->num_supplies,
+tegra->supplies);
And this
This again seems to be issue with my outlook. Will correct it.
}
static int tegra_ahci_controller_init(struct ahci_host_priv *hpriv) {
struct tegra_ahci_priv *tegra = hpriv->plat_data;
int ret;
- unsigned int val;
- struct sata_pad_calibration calib;
+ u32 val;
ret = tegra_ahci_power_on(hpriv);
- if (ret) {
- dev_err(&tegra->pdev->dev,
- "failed to power on AHCI controller: %d\n", ret);
+ if (ret)
return ret;
- }
+ /*
+ * Program the following SATA IPFS registers
Extra space between "following" and "SATA"
Okay, will correct it.
+ * to allow SW accesses to SATA's MMIO Register
Perhaps say "register range"
+ */
+ val = readl(tegra->sata_regs + SATA_FPCI_BAR5);
+ val &= ~(SATA_FPCI_BAR5_START_MASK |
SATA_FPCI_BAR5_ACCESS_TYPE);
+ val |= SATA_FPCI_BAR5_START | SATA_FPCI_BAR5_ACCESS_TYPE;
+ writel(val, tegra->sata_regs + SATA_FPCI_BAR5);
+
+ /* Program the following SATA IPFS register to enable the SATA */
val = readl(tegra->sata_regs + SATA_CONFIGURATION_0);
- val |= SATA_CONFIGURATION_EN_FPCI;
+ val |= SATA_CONFIGURATION_0_EN_FPCI;
writel(val, tegra->sata_regs + SATA_CONFIGURATION_0);
- /* Pad calibration */
-
- ret = tegra_fuse_readl(FUSE_SATA_CALIB, &val);
- if (ret) {
- dev_err(&tegra->pdev->dev,
- "failed to read calibration fuse: %d\n", ret);
- return ret;
- }
-
- calib = tegra124_pad_calibration[val & FUSE_SATA_CALIB_MASK];
-
- writel(BIT(0), tegra->sata_regs + SCFG_OFFSET + T_SATA0_INDEX);
-
- val = readl(tegra->sata_regs +
- SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL1_GEN1);
- val &= ~T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_MASK;
- val &= ~T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_MASK;
- val |= calib.gen1_tx_amp <<
- T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_SHIFT;
- val |= calib.gen1_tx_peak <<
- T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_SHIFT;
- writel(val, tegra->sata_regs + SCFG_OFFSET +
- T_SATA0_CHX_PHY_CTRL1_GEN1);
-
- val = readl(tegra->sata_regs +
- SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL1_GEN2);
- val &= ~T_SATA0_CHX_PHY_CTRL1_GEN2_TX_AMP_MASK;
- val &= ~T_SATA0_CHX_PHY_CTRL1_GEN2_TX_PEAK_MASK;
- val |= calib.gen2_tx_amp <<
- T_SATA0_CHX_PHY_CTRL1_GEN1_TX_AMP_SHIFT;
- val |= calib.gen2_tx_peak <<
- T_SATA0_CHX_PHY_CTRL1_GEN1_TX_PEAK_SHIFT;
- writel(val, tegra->sata_regs + SCFG_OFFSET +
- T_SATA0_CHX_PHY_CTRL1_GEN2);
-
- writel(T_SATA0_CHX_PHY_CTRL11_GEN2_RX_EQ,
- tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL11);
- writel(T_SATA0_CHX_PHY_CTRL2_CDR_CNTL_GEN1,
- tegra->sata_regs + SCFG_OFFSET + T_SATA0_CHX_PHY_CTRL2);
-
- writel(0, tegra->sata_regs + SCFG_OFFSET + T_SATA0_INDEX);
-
- /* Program controller device ID */
+ /* Electrical settings for better link stability */
+ val = T_SATA0_CHX_PHY_CTRL17_0_RX_EQ_CTRL_L_GEN1;
+ writel(val, tegra->sata_regs + SCFG_OFFSET +
T_SATA0_CHX_PHY_CTRL17_0);
+ val = T_SATA0_CHX_PHY_CTRL18_0_RX_EQ_CTRL_L_GEN2;
+ writel(val, tegra->sata_regs + SCFG_OFFSET +
T_SATA0_CHX_PHY_CTRL18_0);
+ val = T_SATA0_CHX_PHY_CTRL20_0_RX_EQ_CTRL_H_GEN1;
+ writel(val, tegra->sata_regs + SCFG_OFFSET +
T_SATA0_CHX_PHY_CTRL20_0);
+ val = T_SATA0_CHX_PHY_CTRL21_0_RX_EQ_CTRL_H_GEN2;
+ writel(val, tegra->sata_regs + SCFG_OFFSET +
+T_SATA0_CHX_PHY_CTRL21_0);
Indent
+
+ /* For SQUELCH Filter & Gen3 drive getting detected as Gen1 drive
+*/
+
+ val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA_CFG_PHY_0);
+ val |= T_SATA_CFG_PHY_0_MASK_SQUELCH;
+ val &= ~T_SATA_CFG_PHY_0_USE_7BIT_ALIGN_DET_FOR_SPD;
+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA_CFG_PHY_0);
+
+ val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_NVOOB);
+ val &= ~(T_SATA0_NVOOB_COMMA_CNT_MASK |
+ T_SATA0_NVOOB_SQUELCH_FILTER_LENGTH_MASK |
+ T_SATA0_NVOOB_SQUELCH_FILTER_MODE_MASK);
+ val |= (T_SATA0_NVOOB_COMMA_CNT |
+ T_SATA0_NVOOB_SQUELCH_FILTER_LENGTH |
+ T_SATA0_NVOOB_SQUELCH_FILTER_MODE);
+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_NVOOB);
+
+ /*
+ * Change CFG2NVOOB_2_COMWAKE_IDLE_CNT_LOW from 83.3 ns to
58.8ns
+ */
+ val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG2NVOOB_2);
+ val &= ~T_SATA0_CFG2NVOOB_2_COMWAKE_IDLE_CNT_LOW_MASK;
+ val |= T_SATA0_CFG2NVOOB_2_COMWAKE_IDLE_CNT_LOW;
+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG2NVOOB_2);
+
+ if (tegra->soc_data->ops.init)
+ tegra->soc_data->ops.init(hpriv);
+
+ /*
+ * Program the following SATA configuration registers
+ * to initialize SATA
+ */
+ val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_1);
+ val |= (T_SATA0_CFG_1_IO_SPACE | T_SATA0_CFG_1_MEMORY_SPACE |
+ T_SATA0_CFG_1_BUS_MASTER | T_SATA0_CFG_1_SERR);
+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_1);
+ val = T_SATA0_CFG_9_BASE_ADDRESS;
+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_9);
+ /* Program Class Code and Programming interface for SATA */
val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_SATA);
val |= T_SATA0_CFG_SATA_BACKDOOR_PROG_IF_EN;
writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_SATA);
- writel(0x01060100, tegra->sata_regs + SCFG_OFFSET +
T_SATA0_BKDOOR_CC);
+ val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_BKDOOR_CC);
+ val &=
+ ~(T_SATA0_BKDOOR_CC_CLASS_CODE_MASK |
+ T_SATA0_BKDOOR_CC_PROG_IF_MASK);
+ val |= T_SATA0_BKDOOR_CC_CLASS_CODE |
T_SATA0_BKDOOR_CC_PROG_IF;
+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_BKDOOR_CC);
val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_SATA);
val &= ~T_SATA0_CFG_SATA_BACKDOOR_PROG_IF_EN;
writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_SATA);
- /* Enable IO & memory access, bus master mode */
-
- val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_1);
- val |= T_SATA0_CFG_1_IO_SPACE | T_SATA0_CFG_1_MEMORY_SPACE |
- T_SATA0_CFG_1_BUS_MASTER | T_SATA0_CFG_1_SERR;
- writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_1);
-
- /* Program SATA MMIO */
-
- writel(0x10000 << SATA_FPCI_BAR5_START_SHIFT,
- tegra->sata_regs + SATA_FPCI_BAR5);
-
- writel(0x08000 << T_SATA0_CFG_9_BASE_ADDRESS_SHIFT,
- tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_9);
+ /* Enabling LPM capabilities through Backdoor Programming */
+ val = readl(tegra->sata_regs + SCFG_OFFSET +
T_SATA0_AHCI_HBA_CAP_BKDR);
+ val |= (T_SATA0_AHCI_HBA_CAP_BKDR_PARTIAL_ST_CAP |
+ T_SATA0_AHCI_HBA_CAP_BKDR_SLUMBER_ST_CAP |
+ T_SATA0_AHCI_HBA_CAP_BKDR_SALP |
+ T_SATA0_AHCI_HBA_CAP_BKDR_SUPP_PM);
+ writel(val, tegra->sata_regs + SCFG_OFFSET +
+T_SATA0_AHCI_HBA_CAP_BKDR);
+
+ /* SATA Second Level Clock Gating configuration
+ * Enabling Gating of Tx/Rx clocks and driving Pad IDDQ and Lane
+ * IDDQ Signals
+ */
+ val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_35);
+ val &= ~T_SATA0_CFG_35_IDP_INDEX_MASK;
+ val |= T_SATA0_CFG_35_IDP_INDEX;
+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_35);
+
+ val = T_SATA0_AHCI_IDP1_DATA;
+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_AHCI_IDP1);
+
+ val = readl(tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_PHY_1);
+ val |= (T_SATA0_CFG_PHY_1_PADS_IDDQ_EN |
+ T_SATA0_CFG_PHY_1_PAD_PLL_IDDQ_EN);
+ writel(val, tegra->sata_regs + SCFG_OFFSET + T_SATA0_CFG_PHY_1);
+
+ /*
+ * Indicate Sata only has the capability to enter DevSleep
Stray space in front
Okay, will correct it.
+ * from slumber link.
+ */
+
+ val = readl(tegra->sata_aux_regs + SATA_AUX_MISC_CNTL_1_0);
+ val |= SATA_AUX_MISC_CNTL_1_0_DESO_SUPPORT;
+ writel(val, tegra->sata_aux_regs + SATA_AUX_MISC_CNTL_1_0);
+
+ /* Enabling IPFS Clock Gating */
+ val = readl(tegra->sata_regs + SATA_CONFIGURATION_0);
+ val &= ~SATA_CONFIGURATION_0_CLK_OVERRIDE;
+ writel(val, tegra->sata_regs + SATA_CONFIGURATION_0);
- /* Unmask SATA interrupts */
+ tegra_ahci_handle_quirks(hpriv);
val = readl(tegra->sata_regs + SATA_INTR_MASK);
val |= SATA_INTR_MASK_IP_INT_MASK;
@@ -278,7 +456,7 @@ static struct ata_port_operations
ahci_tegra_port_ops = {
.host_stop = tegra_ahci_host_stop,
};
-static const struct ata_port_info ahci_tegra_port_info = {
+static struct ata_port_info ahci_tegra_port_info = {
.flags = AHCI_FLAG_COMMON,
.pio_mask = ATA_PIO4,
.udma_mask = ATA_UDMA6,
@@ -286,7 +464,14 @@ static const struct ata_port_info
ahci_tegra_port_info = { };
static const struct of_device_id tegra_ahci_of_match[] = {
- { .compatible = "nvidia,tegra124-ahci" },
+ {
+ .compatible = "nvidia,tegra124-ahci",
+ .data = &tegra124_ahci_soc_data
+ },
+ {
+ .compatible = "nvidia,tegra210-ahci",
+ .data = &tegra210_ahci_soc_data
+ },
{}
};
MODULE_DEVICE_TABLE(of, tegra_ahci_of_match); @@ -295,12 +480,27
@@
static struct scsi_host_template ahci_platform_sht = {
AHCI_SHT(DRV_NAME),
};
+static void tegra_ahci_handle_quirks(struct ahci_host_priv *hpriv) {
+ struct tegra_ahci_priv *tegra = hpriv->plat_data;
+ u32 val;
+
+ if (tegra->soc_data->quirks & NO_DEVSLP) {
+ val = readl(tegra->sata_aux_regs + SATA_AUX_MISC_CNTL_1_0);
+ val &= ~SATA_AUX_MISC_CNTL_1_0_SDS_SUPPORT;
+ writel(val, tegra->sata_aux_regs + SATA_AUX_MISC_CNTL_1_0);
+ } else if (tegra->soc_data->quirks & NO_DIPM) {
I don't think this should be 'else if', but just two separate regular 'if's?
Okay, will correct it.
+ ahci_tegra_port_info.flags |= ATA_FLAG_NO_DIPM;
Looking at the downstream device trees, it looks like DIPM and DEVSLP are still
disabled for Tegra186 - so why don't we just hardcode these quirks, by always
writing the MISC_CNTL_1_0 register and just adding ATA_FLAG_NO_DIPM to
ahci_tegra_port_info's static definition.
For Tegra186 the devslp pin is shared with PCIE clk req pin.
In downstream PCIe driver by default assumes that CLKREQ is present and it owns it.
So by default devslp is disabled. We verify devslp by making sure that pcie does not
own this pin. This issue will be fixed in future chips.
Ok. How about DIPM, can we hardcode that? If not, or if it is fixed in
Xavier, I think it would be cleaner to have two static port_info structs
and select between then based on the quirk, so that we don't need to
mutate the static data.
+ }
+}
+
static int tegra_ahci_probe(struct platform_device *pdev) {
struct ahci_host_priv *hpriv;
struct tegra_ahci_priv *tegra;
struct resource *res;
int ret;
+ unsigned int i;
hpriv = ahci_platform_get_resources(pdev);
if (IS_ERR(hpriv))
@@ -311,13 +511,18 @@ static int tegra_ahci_probe(struct
platform_device
*pdev)
return -ENOMEM;
hpriv->plat_data = tegra;
-
tegra->pdev = pdev;
+ tegra->soc_data =
+ (struct tegra_ahci_soc *)of_device_get_match_data(&pdev->dev);
res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
tegra->sata_regs = devm_ioremap_resource(&pdev->dev, res);
if (IS_ERR(tegra->sata_regs))
return PTR_ERR(tegra->sata_regs);
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 2);
+ tegra->sata_aux_regs = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(tegra->sata_aux_regs))
+ return PTR_ERR(tegra->sata_aux_regs);
Requiring aux_regs would break backwards compatibility for Tegra124 device
trees. We will have to keep aux_regs optional for Tegra124, and skip writes to
them if they are not available.
As explained in the other patch, In current driver changes we are touching the
devslp register to disable DevSlp which is a part of AUX for both t124 and t210.
By default the devslp is enabled for T124 and T210. (Reset value is 1).
I will add this aux register in T124 node as well.
According to device tree stability, the kernel must work with older
device trees that had support for the device. So for T124, we need to
continue to support older device trees without the aux_regs property.
tegra->sata_rst = devm_reset_control_get(&pdev->dev, "sata");
if (IS_ERR(tegra->sata_rst)) {
@@ -343,13 +548,17 @@ static int tegra_ahci_probe(struct
platform_device
*pdev)
return PTR_ERR(tegra->sata_clk);
}
- tegra->supplies[0].supply = "avdd";
- tegra->supplies[1].supply = "hvdd";
- tegra->supplies[2].supply = "vddio";
- tegra->supplies[3].supply = "target-5v";
- tegra->supplies[4].supply = "target-12v";
+ tegra->supplies = devm_kcalloc(&pdev->dev,
+ tegra->soc_data->num_supplies,
+ sizeof(*tegra->supplies), GFP_KERNEL);
+ if (!tegra->supplies)
+ return -ENOMEM;
+
+ for (i = 0; i < tegra->soc_data->num_supplies; i++)
+ tegra->supplies[i].supply = tegra->soc_data->supply_names[i];
- ret = devm_regulator_bulk_get(&pdev->dev, ARRAY_SIZE(tegra-
supplies),
+ ret = devm_regulator_bulk_get(&pdev->dev,
+ tegra->soc_data->num_supplies,
tegra->supplies);
if (ret) {
dev_err(&pdev->dev, "Failed to get regulators\n"); @@ -385,5
+594,5 @@ static struct platform_driver tegra_ahci_driver = {
module_platform_driver(tegra_ahci_driver);
MODULE_AUTHOR("Mikko Perttunen <mperttunen@xxxxxxxxxx>");
-MODULE_DESCRIPTION("Tegra124 AHCI SATA driver");
+MODULE_DESCRIPTION("Tegra AHCI SATA driver");
MODULE_LICENSE("GPL v2");
--
2.1.4
--
To unsubscribe from this list: send the line "unsubscribe linux-tegra"
in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo
info at http://vger.kernel.org/majordomo-info.html
Thanks for posting!
Mikko
--
To unsubscribe from this list: send the line "unsubscribe linux-tegra" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
--
To unsubscribe from this list: send the line "unsubscribe linux-tegra" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
