I get a hang with Linux on the TX1 developer kit and 4.9.0-rc8.
One of the last lines I see is:
> tegra-mc 70019000.memory-controller: gpuswr: write @0x00000003fffffff0: Page fault (SMMU translation error [--S])
When I remove all GPU modules from the disk (/lib/modules/.../kernel/drivers/gpu)
the system boot successfully.
I've attached the boot log.
--
Martin Michlmayr
http://www.cyrius.com/
U-Boot 2016.09+dfsg1-2 (Oct 24 2016 - 02:36:36 +0000)
TEGRA210
Model: NVIDIA P2371-2180
Board: NVIDIA P2371-2180
DRAM: 3.5 GiB
MMC: Tegra SD/MMC: 0, Tegra SD/MMC: 1
In: serial
Out: serial
Err: serial
Net: No ethernet found.
Hit any key to stop autoboot: 2 1 0
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:1...
Found U-Boot script /boot.scr
2176 bytes read in 78 ms (26.4 KiB/s)
## Executing script at 90000000
13558272 bytes read in 919 ms (14.1 MiB/s)
51409 bytes read in 108 ms (464.8 KiB/s)
16399539 bytes read in 1077 ms (14.5 MiB/s)
Booting Debian 4.9.0-rc8-arm64 from mmc 1:1...
## Flattened Device Tree blob at 82000000
Booting using the fdt blob at 0x82000000
Using Device Tree in place at 0000000082000000, end 000000008200f8d0
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Linux version 4.9.0-rc8-arm64 (debian-kernel@xxxxxxxxxxxxxxxx) (gcc version 6.2.1 20161124 (Debian 6.2.1-5) ) #1 SMP Debian 4.9~rc8-1~exp1 (2016-12-05)
[ 0.000000] Boot CPU: AArch64 Processor [411fd071]
[ 0.000000] efi: Getting EFI parameters from FDT:
[ 0.000000] efi: UEFI not found.
[ 0.000000] /cpus/cpu@1: missing enable-method property
[ 0.000000] /cpus/cpu@2: missing enable-method property
[ 0.000000] /cpus/cpu@3: missing enable-method property
[ 0.000000] percpu: Embedded 22 pages/cpu @ffff8000fff8a000 s50072 r8192 d31848 u90112
[ 0.000000] Detected PIPT I-cache on CPU0
[ 0.000000] CPU features: enabling workaround for ARM erratum 832075
[ 0.000000] CPU features: enabling workaround for ARM erratum 834220
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 903168
[ 0.000000] Kernel command line:
[ 0.000000] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000] software IO TLB [mem 0xdbfff000-0xdffff000] (64MB) mapped at [ffff80005bfff000-ffff80005fffefff]
[ 0.000000] Memory: 3501920K/3670016K available (6780K kernel code, 1016K rwdata, 2156K rodata, 3264K init, 626K bss, 168096K reserved, 0K cma-reserved)
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] modules : 0xffff000000000000 - 0xffff000008000000 ( 128 MB)
[ 0.000000] vmalloc : 0xffff000008000000 - 0xffff7dffbfff0000 (129022 GB)
[ 0.000000] .text : 0xffff000008080000 - 0xffff000008720000 ( 6784 KB)
[ 0.000000] .rodata : 0xffff000008720000 - 0xffff000008940000 ( 2176 KB)
[ 0.000000] .init : 0xffff000008940000 - 0xffff000008c70000 ( 3264 KB)
[ 0.000000] .data : 0xffff000008c70000 - 0xffff000008d6e200 ( 1017 KB)
[ 0.000000] .bss : 0xffff000008d6e200 - 0xffff000008e0ac34 ( 627 KB)
[ 0.000000] fixed : 0xffff7dfffe7fd000 - 0xffff7dfffec00000 ( 4108 KB)
[ 0.000000] PCI I/O : 0xffff7dfffee00000 - 0xffff7dffffe00000 ( 16 MB)
[ 0.000000] vmemmap : 0xffff7e0000000000 - 0xffff800000000000 ( 2048 GB maximum)
[ 0.000000] 0xffff7e0000000000 - 0xffff7e0004000000 ( 64 MB actual)
[ 0.000000] memory : 0xffff800000000000 - 0xffff800100000000 ( 4096 MB)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] Build-time adjustment of leaf fanout to 64.
[ 0.000000] RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=1.
[ 0.000000] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=1
[ 0.000000] NR_IRQS:64 nr_irqs:64 0
[ 0.000000] GIC: Using split EOI/Deactivate mode
[ 0.000000] /interrupt-controller@60004000: 192 interrupts forwarded to /interrupt-controller@50041000
[ 0.000000] PLL_MB already enabled. Postponing set full defaults
[ 0.000000] PLL_U already enabled. Postponing set full defaults
[ 0.000000] PLL_P already enabled. Postponing set full defaults
[ 0.000000] PLL_X already enabled. Postponing set full defaults
[ 0.000000] boot misc1 0x0: expected 0x20
[ 0.000000] (comparison mask = 0xffffff)
[ 0.000000] arm_arch_timer: Architected cp15 timer(s) running at 19.20MHz (phys).
[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[ 0.000003] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[ 0.000258] Console: colour dummy device 80x25
[ 0.000722] console [tty0] enabled
[ 0.000743] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=76800)
[ 0.000767] pid_max: default: 32768 minimum: 301
[ 0.000890] Security Framework initialized
[ 0.000905] Yama: disabled by default; enable with sysctl kernel.yama.*
[ 0.000929] AppArmor: AppArmor disabled by boot time parameter
[ 0.000975] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.000990] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.001613] ftrace: allocating 24565 entries in 96 pages
[ 0.041431] ASID allocator initialised with 65536 entries
[ 0.043065] Speedo Revision 4
[ 0.043097] Tegra Revision: A02 SKU: 23 CPU Process: 0 SoC Process: -22
[ 0.043720] EFI services will not be available.
[ 0.043865] Brought up 1 CPUs
[ 0.043879] SMP: Total of 1 processors activated.
[ 0.043896] CPU features: detected feature: 32-bit EL0 Support
[ 0.043914] CPU: All CPU(s) started at EL2
[ 0.043933] alternatives: patching kernel code
[ 0.045053] devtmpfs: initialized
[ 0.055076] DMI not present or invalid.
[ 0.055256] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.055347] pinctrl core: initialized pinctrl subsystem
[ 0.056231] NET: Registered protocol family 16
[ 0.056880] cpuidle: using governor ladder
[ 0.056894] cpuidle: using governor menu
[ 0.056929] vdso: 2 pages (1 code @ ffff000008727000, 1 data @ ffff000008c75000)
[ 0.056954] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.057091] DMA: preallocated 256 KiB pool for atomic allocations
[ 0.058062] Serial: AMBA PL011 UART driver
[ 0.068577] tegra-mc 70019000.memory-controller: no memory timings for RAM code 0 registered
[ 0.074024] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.074720] ACPI: Interpreter disabled.
[ 0.074963] vgaarb: loaded
[ 0.075132] dmi: Firmware registration failed.
[ 0.075696] clocksource: Switched to clocksource arch_sys_counter
[ 0.097478] VFS: Disk quotas dquot_6.6.0
[ 0.097543] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.097721] pnp: PnP ACPI: disabled
[ 0.104167] NET: Registered protocol family 2
[ 0.104572] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.104712] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[ 0.104935] TCP: Hash tables configured (established 32768 bind 32768)
[ 0.104992] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.105030] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[ 0.105180] NET: Registered protocol family 1
[ 0.105353] Unpacking initramfs...
[ 0.867685] Freeing initrd memory: 16012K (ffff800002100000 - ffff8000030a3000)
[ 0.867955] kvm [1]: 8-bit VMID
[ 0.867970] kvm [1]: IDMAP page: 8070b000
[ 0.867983] kvm [1]: HYP VA range: 800000000000:ffffffffffff
[ 0.868517] kvm [1]: Hyp mode initialized successfully
[ 0.868556] kvm [1]: vgic-v2@50044000
[ 0.868608] kvm [1]: vgic interrupt IRQ1
[ 0.868629] kvm [1]: virtual timer IRQ4
[ 0.869746] futex hash table entries: 256 (order: 3, 32768 bytes)
[ 0.869807] audit: initializing netlink subsys (disabled)
[ 0.869866] audit: type=2000 audit(0.835:1): initialized
[ 0.870174] Initialise system trusted keyrings
[ 0.870357] workingset: timestamp_bits=46 max_order=20 bucket_order=0
[ 0.870425] zbud: loaded
[ 0.977471] Key type asymmetric registered
[ 0.977486] Asymmetric key parser 'x509' registered
[ 0.977549] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[ 0.977633] io scheduler noop registered
[ 0.977646] io scheduler deadline registered
[ 0.977674] io scheduler cfq registered (default)
[ 0.985732] tegra-apbdma 60020000.dma: Tegra20 APB DMA driver register 32 channels
[ 0.986183] tegra-pmc 7000e400.pmc: i2c-thermtrip node not found, emergency thermal reset disabled.
[ 0.986440] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.987610] 70006000.serial: ttyS0 at MMIO 0x70006000 (irq = 316, base_baud = 25500000) is a Tegra
[ 1.682209] console [ttyS0] enabled
[ 1.685967] Serial: AMBA driver
[ 1.689221] msm_serial: driver initialized
[ 1.693429] Unable to detect cache hierarchy from DT for CPU 0
[ 1.699568] mousedev: PS/2 mouse device common for all mice
[ 1.705595] tegra_rtc 7000e000.rtc: rtc core: registered 7000e000.rtc as rtc1
[ 1.712778] tegra_rtc 7000e000.rtc: Tegra internal Real Time Clock
[ 1.719749] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when cpu reaches 102500 mC
[ 1.729236] tegra_soctherm 700e2000.thermal-sensor: throttrip: will throttle when cpu reaches 98500 mC
[ 1.738603] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when gpu reaches 103000 mC
[ 1.748085] tegra_soctherm 700e2000.thermal-sensor: throttrip: will throttle when gpu reaches 100000 mC
[ 1.757542] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when pll reaches 103000 mC
[ 1.767022] tegra_soctherm 700e2000.thermal-sensor: throttrip: pll: missing hot temperature
[ 1.775417] tegra_soctherm 700e2000.thermal-sensor: thermtrip: will shut down when mem reaches 103000 mC
[ 1.784896] tegra_soctherm 700e2000.thermal-sensor: throttrip: mem: missing hot temperature
[ 1.793496] ledtrig-cpu: registered to indicate activity on CPUs
[ 1.799507] dmi-sysfs: dmi entry is absent.
[ 1.803981] NET: Registered protocol family 10
[ 1.808939] mip6: Mobile IPv6
[ 1.811936] NET: Registered protocol family 17
[ 1.816390] mpls_gso: MPLS GSO support
[ 1.820532] registered taskstats version 1
[ 1.824640] Loading compiled-in X.509 certificates
[ 1.833452] alg: No test for pkcs1pad(rsa,sha256) (pkcs1pad(rsa-generic,sha256))
[ 1.841537] Loaded X.509 cert 'Debian Project: Ben Hutchings: 008a018dca80932630'
[ 1.849117] zswap: loaded using pool lzo/zbud
[ 1.858916] hctosys: unable to open rtc device (rtc0)
[ 1.866532] Freeing unused kernel memory: 3264K (ffff800000940000 - ffff800000c70000)
Loading, please wait...
starting version 232
[ 1.908787] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 1.917872] random: udevadm: uninitialized urandom read (16 bytes read)
[ 1.924817] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 1.932098] random: udevadm: uninitialized urandom read (16 bytes read)
[ 1.938779] random: systemd-udevd: uninitialized urandom read (16 bytes read)
[ 1.946387] random: udevadm: uninitialized urandom read (16 bytes read)
[ 1.955082] random: udevadm: uninitialized urandom read (16 bytes read)
[ 1.961938] random: udevadm: uninitialized urandom read (16 bytes read)
[ 1.968811] random: udevadm: uninitialized urandom read (16 bytes read)
[ 1.975639] random: udevadm: uninitialized urandom read (16 bytes read)
[ 2.091330] i2c_tegra: module verification failed: signature and/or required key missing - tainting kernel
[ 2.120780] sdhci: Secure Digital Host Controller Interface driver
[ 2.126986] sdhci: Copyright(c) Pierre Ossman
[ 2.137750] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.167845] usb2-0 supply vbus not found, using dummy regulator
[ 2.180978] usbcore: registered new interface driver usbfs
[ 2.200450] tegra-xusb-padctl 7009f000.padctl: failed to setup XUSB ports: -517
[ 2.213798] usbcore: registered new interface driver hub
[ 2.238287] usb2-0 supply vbus not found, using dummy regulator
[ 2.244341] sdhci-tegra 700b0000.sdhci: Got CD GPIO
[ 2.249366] usbcore: registered new device driver usb
[ 2.261860] 0-0074 supply vcc not found, using dummy regulator
[ 2.276326] tegra-xusb-padctl 7009f000.padctl: failed to setup XUSB ports: -517
[ 2.292921] mmc0: Unknown controller version (3). You may experience problems.
[ 2.324467] sdhci-tegra 700b0000.sdhci: Got CD GPIO
[ 2.339253] usb2-0 supply vbus not found, using dummy regulator
[ 2.352725] tegra-xusb-padctl 7009f000.padctl: failed to setup XUSB ports: -517
[ 2.363725] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] using ADMA 64-bit
[ 2.373357] sdhci-tegra 700b0000.sdhci: Got CD GPIO
[ 2.378465] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe
[ 2.407856] usb2-0 supply vbus not found, using dummy regulator
[ 2.415118] tegra-xusb 70090000.usb: Failed to get supply 'dvddio-pex': -517
[ 2.422176] tegra-xusb 70090000.usb: failed to get regulators: -517
[ 2.431723] tegra-xusb-padctl 7009f000.padctl: failed to setup XUSB ports: -517
[ 2.446111] max77620 1-003c: PMIC Version OTP:0x35 and ES:0x8
[ 2.458672] sdhci-tegra 700b0000.sdhci: Got CD GPIO
[ 2.465692] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe
[ 2.480646] mmc0: new high speed MMC card at address 0001
[ 2.492767] usb2-0 supply vbus not found, using dummy regulator
[ 2.499678] mmcblk0: mmc0:0001 016G32 14.7 GiB
[ 2.504487] tegra-xusb-padctl 7009f000.padctl: failed to setup XUSB ports: -517
[ 2.512033] mmcblk0boot0: mmc0:0001 016G32 partition 1 4.00 MiB
[ 2.523415] mmcblk0boot1: mmc0:0001 016G32 partition 2 4.00 MiB
[ 2.529644] mmcblk0rpmb: mmc0:0001 016G32 partition 3 4.00 MiB
[ 2.535537] VDD_5V0_SYS: supplied by VDD_SYS_MUX
[ 2.541554] RTL_5V: supplied by VDD_5V0_SYS
[ 2.546088] USB_VBUS_EN1: supplied by VDD_5V0_SYS
[ 2.551002] VDD_HDMI_5V0: supplied by VDD_5V0_SYS
[ 2.555835] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 p18
[ 2.564796] VDD_3V3_SYS: supplied by VDD_SYS_MUX
[ 2.574164] random: fast init done
[ 2.579346] VDD_3V3_SD: supplied by VDD_3V3_SYS
[ 2.589755] VDD_DIS_3V3_LCD: supplied by VDD_3V3_SYS
[ 2.595261] sdhci-tegra 700b0000.sdhci: Got CD GPIO
[ 2.600945] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe
[ 2.620670] usb2-0 supply vbus not found, using dummy regulator
[ 2.627050] usb2-3 supply vbus not found, using dummy regulator
[ 2.633166] usb3-0 supply vbus not found, using dummy regulator
[ 2.639462] usb3-1 supply vbus not found, using dummy regulator
[ 2.645906] max77686-rtc max77620-rtc: rtc core: registered max77620-rtc as rtc0
[ 2.690986] VDD_LCD_1V8_DIS: supplied by VDD_1V8
[ 2.707565] AVDD_DSI_CSI_1V2: supplied by AVDD_SYS_1V2
[ 2.715926] 70090000.usb supply dvdd-pex-pll not found, using dummy regulator
[ 2.724206] 70090000.usb supply hvdd-pex-pll-e not found, using dummy regulator
[ 2.732248] VDD_CAM_HV: Bringing 3100000uV into 2800000-2800000uV
[ 2.739776] tegra-xusb 70090000.usb: firmware: direct-loading firmware nvidia/tegra210/xusb.bin
[ 2.749656] VDD_RTC: Bringing 1000000uV into 850000-850000uV
[ 2.757234] VDD_TS_HV: Bringing 3100000uV into 3300000-3300000uV
[ 2.764813] VDD_TS_1V8: Bringing 2800000uV into 1800000-1800000uV
[ 2.808414] tegra-xusb 70090000.usb: Firmware timestamp: 2015-08-10 09:47:54 UTC
[ 2.829014] tegra-xusb 70090000.usb: xHCI Host Controller
[ 2.834851] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 1
[ 2.843593] tegra-xusb 70090000.usb: hcc params 0x0184f525 hci version 0x100 quirks 0x00010010
[ 2.852337] tegra-xusb 70090000.usb: irq 322, io mem 0x70090000
[ 2.858471] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 2.865278] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.872506] usb usb1: Product: xHCI Host Controller
[ 2.877387] usb usb1: Manufacturer: Linux 4.9.0-rc8-arm64 xhci-hcd
[ 2.883571] usb usb1: SerialNumber: 70090000.usb
[ 2.944289] hub 1-0:1.0: USB hub found
[ 2.948669] hub 1-0:1.0: 5 ports detected
[ 2.953596] tegra-xusb 70090000.usb: xHCI Host Controller
[ 2.959280] tegra-xusb 70090000.usb: new USB bus registered, assigned bus number 2
[ 2.967352] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 2.976039] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003
[ 2.982853] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 2.990082] usb usb2: Product: xHCI Host Controller
[ 2.994962] usb usb2: Manufacturer: Linux 4.9.0-rc8-arm64 xhci-hcd
[ 3.001143] usb usb2: SerialNumber: 70090000.usb
[ 3.008543] hub 2-0:1.0: USB hub found
[ 3.012630] hub 2-0:1.0: 4 ports detected
[ 3.017944] sdhci-tegra 700b0000.sdhci: Got CD GPIO
[ 3.023595] mmc1: Unknown controller version (3). You may experience problems.
Begin: Loading essential drivers ... [ 3.084129] mmc1: SDHCI controller on 700b0000.sdhci [700b0000.sdhci] using ADMA 64-bit
[ 3.096124] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe
done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
Begin: Waiting for root file system ... [ 3.161108] mmc1: host does not support reading read-only switch, assuming write-enable
[ 3.173569] mmc1: new high speed SDHC card at address aaaa
[ 3.181761] mmcblk1: mmc1:aaaa SS32G 29.7 GiB
[ 3.193330] mmcblk1: p1 p2 p3 p4
[ 3.199088] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe
[ 3.280151] usb 1-2: new high-speed USB device number 2 using tegra-xusb
[ 3.475725] usb 1-3: new high-speed USB device number 3 using tegra-xusb
[ 3.636485] usb 1-3: New USB device found, idVendor=0b95, idProduct=7720
[ 3.643201] usb 1-3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 3.650336] usb 1-3: Product: AX88x72A
[ 3.654090] usb 1-3: Manufacturer: ASIX Elec. Corp.
[ 3.658970] usb 1-3: SerialNumber: 136926
[ 3.666296] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe
[ 3.939709] usb 1-2: new high-speed USB device number 4 using tegra-xusb
[ 4.084531] usb 1-2: New USB device found, idVendor=0955, idProduct=09ff
[ 4.091238] usb 1-2: New USB device strings: Mfr=1, Product=2, SerialNumber=6
[ 4.098373] usb 1-2: Product: USB 10/100/1000 LAN
[ 4.103079] usb 1-2: Manufacturer: Nvidia
[ 4.107092] usb 1-2: SerialNumber: 000001000000
[ 4.113636] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe
Begin: Running /scripts/local-block ... done.
done.
Begin: Will now check root file system ... fsck from util-linux 2.29
fsck: error 2 (No such file or directory) while executing fsck.ext4 for /dev/mmcblk1p2
fsck exited with status code 8
done.
Warning: File system check failed but did not detect errors
[ 9.298724] EXT4-fs (mmcblk1p2): mounted filesystem with ordered data mode. Opts: (null)
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
[ 9.758318] systemd[1]: System time before build time, advancing clock.
[ 9.859421] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 9.898109] systemd[1]: systemd 232 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD +IDN)
[ 9.916424] systemd[1]: Detected architecture arm64.
Welcome to [1mDebian GNU/Linux stretch/sid[0m!
[ 9.936596] systemd[1]: Set hostname to <tx1>.
[ 10.231371] systemd[1]: Listening on udev Kernel Socket.
[[0;32m OK [0m] Listening on udev Kernel Socket.
[ 10.247975] systemd[1]: Listening on Journal Audit Socket.
[[0;32m OK [0m] Listening on Journal Audit Socket.
[ 10.264189] systemd[1]: Created slice User and Session Slice.
[[0;32m OK [0m] Created slice User and Session Slice.
[ 10.283766] systemd[1]: Reached target Remote File Systems.
[[0;32m OK [0m] Reached target Remote File Systems.
[ 10.299871] systemd[1]: Listening on Journal Socket.
[[0;32m OK [0m] Listening on Journal Socket.
[ 10.315834] systemd[1]: Listening on /dev/initctl Compatibility Named Pipe.
[[0;32m OK [0m] Listening on /dev/initctl Compatibility Named Pipe.
[ 10.336090] systemd[1]: Created slice System Slice.
[[0;32m OK [0m] Created slice System Slice.
Mounting Huge Pages File System...
Starting Load Kernel Modules...
[[0;32m OK [0m] Created slice system-getty.slice.
Starting Create list of required st…ce nodes for the current kernel...
Mounting Debug File System...
[[0;32m OK [0m] Created slice system-serial\x2dgetty.slice.
[[0;32m OK [0m] Set up automount Arbitrary Executab…rmats File System Automount Point.
[[0;32m OK [0m] Created slice system-systemd\x2dfsck.slice.
[[0;32m OK [0m] Started Forward Password Requests to Wall Directory Watch.
[[0;32m OK [0m] Listening on Syslog Socket.
[[0;32m OK [0m] Listening on fsck to fsckd communication Socket.
Starting File System Check on Root Device...
[[0;32m OK [0m] Listening on udev Control Socket.
[[0;32m OK [0m] Started Dispatch Password Requests to Console Directory Watch.
[[0;32m OK [0m] Reached target Paths.
[[0;32m OK [0m] Reached target Encrypted Volumes.
[[0;32m OK [0m] Reached target Slices.
Mounting POSIX Message Queue File System...
[[0;32m OK [0m] Listening on Journal Socket (/dev/log).
Starting Journal Service...
[[0;32m OK [0m] Mounted POSIX Message Queue File System.
[[0;32m OK [0m] Mounted Debug File System.
[[0;32m OK [0m] Mounted Huge Pages File System.
[[0;32m OK [0m] Started Load Kernel Modules.
[[0;32m OK [0m] Started Create list of required sta…vice nodes for the current kernel.
[[0;32m OK [0m] Started File System Check Daemon to report status.
Starting Create Static Device Nodes in /dev...
Checking in progress on 1 disk (0.0% complete)
Starting Apply Kernel Variables...
[[0;32m OK [0m] Started Journal Service.
[[0;32m OK [0m] Started Apply Kernel Variables.
[[0;32m OK [0m] Started Create Static Device Nodes in /dev.
Starting udev Kernel Device Manager...
Checking in progress on 1 disk (0.9% complete)
[[0;32m OK [0m] Started udev Kernel Device Manager.
Checking in progress on 1 disk (1.9% complete)
Checking in progress on 1 disk (14.9% complete)
Checking in progress on 1 disk (15.9% complete)
Checking in progress on 1 disk (29.9% complete)
Checking in progress on 1 disk (30.8% complete)
Checking in progress on 1 disk (44.8% complete)
Checking in progress on 1 disk (45.7% complete)
Checking in progress on 1 disk (70.0% complete)
Checking in progress on 1 disk (70.0% complete)
Checking in progress on 1 disk (70.1% complete)
Checking in progress on 1 disk (70.4% complete)
Checking in progress on 1 disk (70.6% complete)
Checking in progress on 1 disk (70.9% complete)
Checking in progress on 1 disk (71.5% complete)
Checking in progress on 1 disk (71.6% complete)
Checking in progress on 1 disk (72.1% complete)
Checking in progress on 1 disk (72.4% complete)
Checking in progress on 1 disk (72.9% complete)
Checking in progress on 1 disk (73.2% complete)
Checking in progress on 1 disk (73.6% complete)
Checking in progress on 1 disk (73.8% complete)
Checking in progress on 1 disk (74.2% complete)
Checking in progress on 1 disk (74.6% complete)
Checking in progress on 1 disk (75.3% complete)
Checking in progress on 1 disk (76.0% complete)
Checking in progress on 1 disk (76.0% complete)
Checking in progress on 1 disk (76.0% complete)
Checking in progress on 1 disk (76.3% complete)
Checking in progress on 1 disk (76.6% complete)
Checking in progress on 1 disk (77.1% complete)
Checking in progress on 1 disk (77.4% complete)
Checking in progress on 1 disk (77.8% complete)
Checking in progress on 1 disk (78.1% complete)
Checking in progress on 1 disk (78.5% complete)
Checking in progress on 1 disk (79.0% complete)
Checking in progress on 1 disk (79.3% complete)
Checking in progress on 1 disk (79.7% complete)
Checking in progress on 1 disk (80.0% complete)
Checking in progress on 1 disk (80.1% complete)
Checking in progress on 1 disk (80.6% complete)
Checking in progress on 1 disk (80.6% complete)
Checking in progress on 1 disk (81.1% complete)
Checking in progress on 1 disk (81.5% complete)
Checking in progress on 1 disk (81.8% complete)
Checking in progress on 1 disk (82.2% complete)
Checking in progress on 1 disk (82.5% complete)
Checking in progress on 1 disk (83.0% complete)
Checking in progress on 1 disk (83.3% complete)
Checking in progress on 1 disk (83.6% complete)
Checking in progress on 1 disk (83.9% complete)
Checking in progress on 1 disk (84.3% complete)
Checking in progress on 1 disk (84.6% complete)
Checking in progress on 1 disk (84.8% complete)
Checking in progress on 1 disk (85.1% complete)
Checking in progress on 1 disk (85.1% complete)
Checking in progress on 1 disk (85.4% complete)
Checking in progress on 1 disk (85.9% complete)
Checking in progress on 1 disk (86.6% complete)
Checking in progress on 1 disk (87.2% complete)
Checking in progress on 1 disk (87.5% complete)
Checking in progress on 1 disk (87.7% complete)
Checking in progress on 1 disk (88.1% complete)
Checking in progress on 1 disk (88.2% complete)
Checking in progress on 1 disk (88.7% complete)
Checking in progress on 1 disk (89.0% complete)
Checking in progress on 1 disk (89.4% complete)
Checking in progress on 1 disk (89.5% complete)
Checking in progress on 1 disk (89.7% complete)
Checking in progress on 1 disk (89.9% complete)
Checking in progress on 1 disk (90.1% complete)
Checking in progress on 1 disk (90.3% complete)
Checking in progress on 1 disk (90.4% complete)
Checking in progress on 1 disk (90.6% complete)
Checking in progress on 1 disk (90.8% complete)
Checking in progress on 1 disk (90.9% complete)
Checking in progress on 1 disk (91.1% complete)
Checking in progress on 1 disk (91.3% complete)
Checking in progress on 1 disk (91.4% complete)
Checking in progress on 1 disk (91.6% complete)
Checking in progress on 1 disk (91.8% complete)
Checking in progress on 1 disk (91.9% complete)
Checking in progress on 1 disk (92.6% complete)
Checking in progress on 1 disk (93.6% complete)
Checking in progress on 1 disk (94.6% complete)
Checking in progress on 1 disk (96.6% complete)
Checking in progress on 1 disk (97.5% complete)
Checking in progress on 1 disk (100.0% complete)
Checking in progress on 0 disks (100.0% complete)
[[0;32m OK [0m] Started File System Check on Root Device.
Starting Remount Root and Kernel File Systems...
[ 12.588657] EXT4-fs (mmcblk1p2): re-mounted. Opts: errors=remount-ro
[[0;32m OK [0m] Started Remount Root and Kernel File Systems.
[[0;32m OK [0m] Reached target Local File Systems (Pre).
Starting Load/Save Random Seed...
Starting udev Coldplug all Devices...
Starting Flush Journal to Persistent Storage...
[[0;32m OK [0m] Started Load/Save Random Seed.
[ 12.695677] systemd-journald[186]: Received request to flush runtime journal from PID 1
[[0;32m OK [0m] Started Flush Journal to Persistent Storage.
[ 12.973592] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe
[[0;32m OK [0m] Started udev Coldplug all Devices.
[[0;32m OK [0m] Found device /dev/ttyS0.
[ 13.099280] 0-002c supply power not found, using dummy regulator
[ 13.120275] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe
[ 13.144235] [drm] Initialized
[ 13.156912] lp855x 0-002c: failed to read 0x00
[ 13.161383] lp855x 0-002c: pre init device err: -121
[ 13.166359] lp855x 0-002c: device config err: -121
[ 13.247809] lp855x: probe of 0-002c failed with error -121
[ 13.294459] tegra-i2c 7000c700.i2c: could not find pctldev for node /host1x@50000000/dpaux@54040000/pinmux-i2c, deferring probe
[ 13.307581] 54040000.dpaux supply vdd not found, using dummy regulator
[ 13.332329] tegra-sor 54580000.sor: failed to probe output: -517
[ 13.367740] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 13.374368] [drm] No driver support for vblank timestamp query.
[ 13.447475] drm drm: No connectors reported connected with modes
[ 13.463272] [drm] Cannot find any crtc or sizes - going 1024x768
[ 13.507394] drm drm: fb0: frame buffer device
[ 13.559928] [drm] Initialized tegra 0.0.0 20120330 on minor 0
[ 13.589237] usbcore: registered new interface driver r8152
[ 13.633884] usbcore: registered new interface driver cdc_ether
[[0;32m OK [0m] Found device /dev/disk/by-uuid/98a72b13-a480-4b9a-8627-04fd7dc8ff7d.
[ 13.728119] usb 1-2: reset high-speed USB device number 4 using tegra-xusb
[ 13.876813] 57000000.gpu supply vdd not found, using dummy regulator
[[0;32m OK [0m] Found device /dev/disk/by-uuid/eac8dd58-c636-472d-89e5-79272fd02d9e.
[[0;32m OK [0m] Found device /dev/disk/by-uuid/b2b4d279-7f34-4d03-b42a-b75c63d70f62.
[ 13.914076] tegra-mc 70019000.memory-controller: gpuswr: write @0x00000003fffffff0: Page fault (SMMU translation error [--S])
[[0;32m OK [0m] Found device /dev/mmcblk1p3.
[ 13.965144] alg: No test for __ecb-aes-ce (__driver-ecb-aes-ce)
[ 13.981054] asix 1-3:1.0 eth0: register 'asix' at usb-70090000.usb-3, ASIX AX88772 USB 2.0 Ethernet, 00:50:b6:13:69:26
[ 14.025201] r8152 1-2:1.0 eth1: v1.08.6
