On Fri, May 13, 2016 at 5:06 PM, Marcel Ziswiler <marcel.ziswiler@xxxxxxxxxxx> wrote: > On Thu, 2016-04-21 at 00:51 +0800, Dong Aisheng wrote: >> Currently if mmc_select_hs200 mode switch fails, MMC core >> can only use legacy mode to run the card. >> Let's retry HS speed mode if HS200 fails. >> >> Before the fix: >> mmc0: mmc_select_hs200 failed, error -74 >> : switch to mmc0 failed >> mmc0: new MMC card at address 0001 >> mmcblk0: mmc0:0001 Q2J55L 7.12 GiB >> mmcblk0boot0: mmc0:0001 Q2J55L partition 1 2.00 MiB >> mmcblk0boot1: mmc0:0001 Q2J55L partition 2 2.00 MiB >> mmcblk0rpmb: mmc0:0001 Q2J55L partition 3 4.00 MiB >> mmcblk0: p1 p2 >> >> After the fix: >> mmc0: mmc_select_hs200 failed, error -74 >> mmc0: new DDR MMC card at address 0001 >> mmcblk0: mmc0:0001 Q2J55L 7.12 GiB >> mmcblk0boot0: mmc0:0001 Q2J55L partition 1 2.00 MiB >> mmcblk0boot1: mmc0:0001 Q2J55L partition 2 2.00 MiB >> mmcblk0rpmb: mmc0:0001 Q2J55L partition 3 4.00 MiB >> mmcblk0: p1 p2 >> >> Signed-off-by: Dong Aisheng <aisheng.dong@xxxxxxx> >> --- >> drivers/mmc/core/mmc.c | 3 ++- >> 1 file changed, 2 insertions(+), 1 deletion(-) >> >> diff --git a/drivers/mmc/core/mmc.c b/drivers/mmc/core/mmc.c >> index 55c8201..b573dc7 100644 >> --- a/drivers/mmc/core/mmc.c >> +++ b/drivers/mmc/core/mmc.c >> @@ -1315,7 +1315,8 @@ static int mmc_select_timing(struct mmc_card >> *card) >> >> if (card->mmc_avail_type & EXT_CSD_CARD_TYPE_HS200) >> err = mmc_select_hs200(card); >> - else if (card->mmc_avail_type & EXT_CSD_CARD_TYPE_HS) >> + >> + if (err && (card->mmc_avail_type & EXT_CSD_CARD_TYPE_HS)) >> err = mmc_select_hs(card); >> >> if (err && err != -EBADMSG) > > > This seems to break on TK1 where eMMC so far was detected as an 8-bit > high speed MMC card. With this patch it reverts to detecting a 1-bit only > MMC card! This has been observed both on a NVIDIA's Jetson TK1 as well as > our new Toradex Apalis TK1 (CC Tegra mailing list, Jon Hunter and Lucas > Stach as well). So far T30 is not affected as there we are still doing > full HS200 with whatever issues that has. > Oh, sorry, just found there's a logic error in the patch. It may wrongly bypass the HS mode select for non hs200 mode eMMCs due to the 'err' condition. Will send a fixed version. Regards Dong Aisheng > Before: > [ 3.726894] sdhci: Secure Digital Host Controller Interface driver > [ 3.733081] sdhci: Copyright(c) Pierre Ossman > [ 3.737462] sdhci-pltfm: SDHCI platform and OF driver helper > [ 3.753411] mmc0: Unknown controller version (3). You may experience > problems. > [ 3.768345] mmc0: Invalid maximum block size, assuming 512 bytes > [ 3.814896] mmc0: SDHCI controller on 700b0600.sdhci [700b0600.sdhci] > using ADMA 64-bit > [ 3.892088] mmc0: new high speed MMC card at address 0001 > [ 3.899194] mmcblk0: mmc0:0001 SEM16G 14.7 GiB > [ 3.904217] mmcblk0boot0: mmc0:0001 SEM16G partition 1 4.00 MiB > [ 3.910645] mmcblk0boot1: mmc0:0001 SEM16G partition 2 4.00 MiB > [ 3.917119] mmcblk0rpmb: mmc0:0001 SEM16G partition 3 4.00 MiB > [ 3.926006] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 > root@jetson_tk1:~# cat /sys/kernel/debug/mmc0/ios > clock: 52000000 Hz > actual clock: 51000000 Hz > vdd: 21 (3.3 ~ 3.4 V) > bus mode: 2 (push-pull) > chip select: 0 (don't care) > power mode: 2 (on) > bus width: 3 (8 bits) > timing spec: 1 (mmc high-speed) > signal voltage: 0 (3.30 V) > driver type: 0 (driver type B) > > After: > [ 3.899918] mmc0: new MMC card at address 0001 > root@jetson_tk1:~# cat /sys/kernel/debug/mmc0/ios > clock: 25000000 Hz > actual clock: 24727273 Hz > vdd: 21 (3.3 ~ 3.4 V) > bus mode: 2 (push-pull) > chip select: 0 (don't care) > power mode: 2 (on) > bus width: 0 (1 bits) > timing spec: 0 (legacy) > signal voltage: 0 (3.30 V) > driver type: 0 (driver type B) > -- To unsubscribe from this list: send the line "unsubscribe linux-tegra" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
