On 12/05/16 13:21, Laxman Dewangan wrote:
> The IO pins of Tegra SoCs are grouped for common control of IO
> interface like setting voltage signal levels and power state of
> the interface. The group is generally referred as IO pads. The
> power state and voltage control of IO pins can be done at IO pads
> level.
>
> Tegra generation SoC supports the power down of IO pads when it
> is not used even in the active state of system. This saves power
> from that IO interface. Also it supports multiple voltage level
> in IO pins for interfacing on some of pads. The IO pad voltage is
> automatically detected till T124, hence SW need not to configure
> this. But from T210, the automatically detection logic has been
> removed, hence SW need to explicitly set the IO pad voltage into
> IO pad configuration registers.
>
> Add support to set the power states and voltage level of the IO pads
> from client driver. The implementation for the APIs are in generic
> which is applicable for all generation os Tegra SoC.
>
> IO pads ID and information of bit field for power state and voltage
> level controls are added for Tegra124, Tegra132 and Tegra210. The SOR
> driver is modified to use the new APIs.
>
> Signed-off-by: Laxman Dewangan <ldewangan@xxxxxxxxxx>
>
> ---
> Changes from V1:
> This is reworked on earlier path to have separation between IO rails and
> io pads and add power state and voltage control APIs in single call.
>
> Changes from V2:
> - Remove the tegra_io_rail_power_off/on() apis and change client (sor) driver
> to use the new APIs for IO pad power.
> - Remove the TEGRA_IO_RAIL_ macros.
>
> Changes from V3:
> - Make all pad_id/io_pad_id to id.
> - tegra_io_pad_ -> tegra_io_pads
> - dpd_bit -> bit, pwr_mask/bit to mask/bit.
> - Rename function to tegra_io_pads_{set,get}_voltage_config
> - Make the io pad tables common for all SoC.
> - Make io_pads enums.
> - Add enums for voltage.
>
> Changes from V4:
> - IO_PAD->IO_PADS
> - TEGRA_IO_PADS_POWER_SOURCE_ -> TEGRA_IO_PADS_VCONF_
> ---
> drivers/gpu/drm/tegra/sor.c | 8 +-
> drivers/soc/tegra/pmc.c | 221 ++++++++++++++++++++++++++++++++++++++------
> include/soc/tegra/pmc.h | 132 ++++++++++++++++++--------
> 3 files changed, 294 insertions(+), 67 deletions(-)
[snip]
> +static int tegra_io_pads_to_voltage_bit(const struct tegra_pmc_soc *soc,
> + enum tegra_io_pads id)
> +{
> + /* T210 only supports io-pad voltage config bit */
> + if (soc->io_pads_soc_mask != TEGRA_IO_PADS_T210)
> return -EINVAL;
If this is only supported for Tegra210, should these voltage functions
be dependent on CONFIG_ARCH_TEGRA_210_SOC? If so, then I am also
wondering if we should bother having the massive look-up table and just
have a smaller table to translate the ID to bit for voltage as you had
in your initial patch? Seems there are few io-pads that support the
voltage configuration.
+#define TEGRA_IO_RAIL_VOLTAGE(_io_rail, _pos) \
+{ \
+ .io_rail_id = TEGRA_IO_RAIL_##_io_rail, \
+ .bit_position = _pos, \
+}
+
+static struct tegra_io_rail_voltage_bit_info
tegra210_io_rail_voltage_info[] = {
+ TEGRA_IO_RAIL_VOLTAGE(SDMMC1, 12),
+ TEGRA_IO_RAIL_VOLTAGE(SDMMC3, 13),
+ TEGRA_IO_RAIL_VOLTAGE(AUDIO_HV, 18),
+ TEGRA_IO_RAIL_VOLTAGE(DMIC, 20),
+ TEGRA_IO_RAIL_VOLTAGE(GPIO, 21),
+ TEGRA_IO_RAIL_VOLTAGE(SPI_HV, 23),
+};
Otherwise, looks fine to me.
Cheers
Jon
--
nvpublic
--
To unsubscribe from this list: send the line "unsubscribe linux-tegra" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
