Hi Jon,
On 04/05/16 17:25, Jon Hunter wrote:
> Setting the interrupt type for private peripheral interrupts (PPIs) may
> not be supported by a given GIC because it is IMPLEMENTATION DEFINED
> whether this is allowed. There is no way to know if setting the type is
> supported for a given GIC and so the value written is read back to
> verify it matches the desired configuration. If it does not match then
> an error is return.
>
> There are cases where the interrupt configuration read from firmware
> (such as a device-tree blob), has been incorrect and hence
> gic_configure_irq() has returned an error. This error has gone
> undetected because the error code returned was ignored but the interrupt
> still worked fine because the configuration for the interrupt could not
> be overwritten.
>
> Given that this has done undetected and that failing to set the
> configuration for a PPI may not be a catastrophic, don't return an error
> but WARN if we fail to configure a PPI. This will allows us to fix up
> any places in the kernel where we should be checking the return status
> and maintain backward compatibility with firmware images that may have
> incorrect PPI configurations.
>
> Signed-off-by: Jon Hunter <jonathanh@xxxxxxxxxx>
> Acked-by: Marc Zyngier <marc.zyngier@xxxxxxx>
> ---
> drivers/irqchip/irq-gic-common.c | 11 +++++++----
> 1 file changed, 7 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/irqchip/irq-gic-common.c b/drivers/irqchip/irq-gic-common.c
> index ffff5a45f1e3..9fa92a17225c 100644
> --- a/drivers/irqchip/irq-gic-common.c
> +++ b/drivers/irqchip/irq-gic-common.c
> @@ -56,12 +56,15 @@ int gic_configure_irq(unsigned int irq, unsigned int type,
>
> /*
> * Write back the new configuration, and possibly re-enable
> - * the interrupt. If we fail to write a new configuration,
> - * return an error.
> + * the interrupt. WARN if we fail to write a new configuration
> + * and return an error if we failed to write the configuration
> + * for an SPI. If we fail to write the configuration for a PPI
> + * this is most likely because the GIC does not allow us to set
> + * the configuration and so it is not a catastrophic failure.
> */
> writel_relaxed(val, base + GIC_DIST_CONFIG + confoff);
> - if (readl_relaxed(base + GIC_DIST_CONFIG + confoff) != val)
> - ret = -EINVAL;
> + if (WARN_ON(readl_relaxed(base + GIC_DIST_CONFIG + confoff) != val))
> + ret = irq < 32 ? 0 : -EINVAL;
>
> if (sync_access)
> sync_access();
>
I'm going to slightly backpedal on that one:
When running in non-secure mode, you can reconfigure secure interrupts
(for obvious reasons). But you don't know which mode you're running in
either. A typical example is the arch timer, which requests both secure
and non-secure interrupts, because we cannot know which side of the CPU
we're running on. In the non-secure case, we end-up with a splat that
is rather undeserved.
So I'm tempted to tone down the splat in the PPI case like this:
diff --git a/drivers/irqchip/irq-gic-common.c b/drivers/irqchip/irq-gic-common.c
index 083c303..1605e42 100644
--- a/drivers/irqchip/irq-gic-common.c
+++ b/drivers/irqchip/irq-gic-common.c
@@ -63,8 +63,17 @@ int gic_configure_irq(unsigned int irq, unsigned int type,
* the configuration and so it is not a catastrophic failure.
*/
writel_relaxed(val, base + GIC_DIST_CONFIG + confoff);
- if (WARN_ON(readl_relaxed(base + GIC_DIST_CONFIG + confoff) != val))
- ret = irq < 32 ? 0 : -EINVAL;
+ oldval = readl_relaxed(base + GIC_DIST_CONFIG + confoff);
+ if (oldval != val) {
+ if (irq < 32) {
+ pr_warn("GIC: PPI%d is either secure or misconfigured\n",
+ irq - 16);
+ ret = 0;
+ } else {
+ WARN_ON(1);
+ ret = -EINVAL;
+ }
+ }
if (sync_access)
sync_access();
Thoughts?
M.
--
Jazz is not dead. It just smells funny...
--
To unsubscribe from this list: send the line "unsubscribe linux-tegra" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
