On 12/04/16 15:56, Laxman Dewangan wrote:
> NVIDIA Tegra210 supports the IO pads which can operate at 1.8V
> or 3.3V I/O voltage levels. Also IO pads can be configured for
> power down state if it is not in used. SW needs to configure the
> voltage level of IO pads based on IO rail voltage and its power
> state based on platform usage.
>
> Add DT binding document for detailing the DT properties for
> configuring IO pads voltage levels and its power state.
>
> Signed-off-by: Laxman Dewangan <ldewangan@xxxxxxxxxx>
> ---
> .../bindings/pinctrl/nvidia,tegra210-io-pad.txt | 102 +++++++++++++++++++++
> .../dt-bindings/pinctrl/pinctrl-tegra210-io-pad.h | 24 +++++
> 2 files changed, 126 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/pinctrl/nvidia,tegra210-io-pad.txt
> create mode 100644 include/dt-bindings/pinctrl/pinctrl-tegra210-io-pad.h
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra210-io-pad.txt b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra210-io-pad.txt
> new file mode 100644
> index 0000000..97cdd4f
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra210-io-pad.txt
> @@ -0,0 +1,102 @@
> +NVIDIA Tegra210 PMC IO pad controller
> +
> +NVIDIA Tegra210 supports IO pads which can operate at 1.8V or 3.3V I/O
> +power rail voltages. SW needs to configure the voltage level of IO pads
> +based on platform specific power tree.
> +
> +The voltage configurations of IO pads should be done in boot if it is not
> +going to change other wise dynamically based on IO rail voltage on that
> +IO pads.
> +
> +The node for the Tegra210 io-pad driver must be sub node of pmc@0,7000e400.
This should be 'pmc@7000e400'. We were incorrectly adding the '0,'
previously.
> +
> +Required properties:
> +- compatible: "nvidia,tegra210-io-pad"
I think you have have "Must be ..." here. I am also wondering if the
pinctrl device should be registered by the pmc driver and so not a
separate driver to the PMC driver. In other words, the PMC driver calls
pinctrl_register() directly.
> +Please refer to <pinctrl-bindings.txt> in this directory for details of the
> +common pinctrl bindings used by client devices, including the meaning of the
> +phrase "pin configuration node".
> +
> +Tegra's pin configuration nodes act as a container for an arbitrary number of
> +subnodes. Each of these subnodes represents some desired configuration for an
> +IO pads, or a list of IO pads. This configuration can include the voltage and
> +power enable/disable control
> +
> +The name of each subnode is not important; all subnodes should be enumerated
> +and processed purely based on their content. Each subnode only affects those
> +parameters that are explicitly listed. Unspecified is represented as an absent
> +property,
> +
> +See the TRM to determine which properties and values apply to each IO pads.
> +Macro values for property values are defined in
> +<dt-bindings/pinctrl/pinctrl-tegra210-io-pad.h>
> +
> +The voltage supported on the pads are 1.8V and 3.3V. The enums are defined as:
> + For 1.8V, use TEGRA210_IO_RAIL_1800000UV
> + For 3.3V, use TEGRA210_IO_RAIL_3300000UV
You may consider just using integer values here like we do for regulators.
> +
> +Required subnode-properties:
> +==========================
> +- pins : An array of strings. Each string contains the name of an IO pads. Valid
> + values for these names are listed below.
Why are they not listed here? Array of strings sounds odd. Array/list of
pin names seems more appropriate.
> +Optional subnode-properties:
> +==========================
> +-nvidia,io-rail-voltage: Integer. The voltage level of IO pads. The
> + valid values are 1.8V and 3.3V. Macros are
> + defined for these voltage levels in
> + <dt-bindings/pinctrl/pinctrl-tegra210-io-pad.h>
> + Use TEGRA210_IO_RAIL_1800000UV for 1.8V
> + Use TEGRA210_IO_RAIL_3300000UV for 3.3V
> +
> +-nvidia,io-pad-deep-power-down: Integer, representing the deep power down state
> + of the IO pads. If this is enable then IO pads
> + will be in power down state and interface is not
> + enabled for any transaction. This is power
> + saving mode of the IO pads. The macros are
> + defined for enable/disable in
> + <dt-bindings/pinctrl/pinctrl-tegra210-io-pad.h>
> + TEGRA210_IO_PAD_DEEP_POWER_DOWN_DISABLE for
> + disable.
> + TEGRA210_IO_PAD_DEEP_POWER_DOWN_ENABLE for
> + enable.
Sounds like a boolean parameter. So may consider that if the property
'nvidia,io-pad-deep-power-down' is present then it means enable
deep-power-down and if not present then don't. Then you do not need to
assign a value to it.
> +Valid values for pin are:
> + audio, audio-hv, cam, csia, csib, csic, csid, csie, csif,
> + dbg, debug-nonao, dmic, dp, dsi, dsib, dsic, dsid, emmc, emmc2,
> + gpio, hdmi, hsic, lvds, mipi-bias, pex-bias, pex-clk1, pex-clk2,
> + pex-ctrl, sdmmc1, sdmmc3, spi, spi-hv, uart, usb-bias, usb0,
> + usb1, usb2, usb3.
> +
> +All IO pads do not support the 1.8V/3.3V configurations. Valid values for
> +nvidia,io-rail-voltage are:
> + audio-hv, dmic, gpio, sdmmc1, sdmmc3, spi-hv.
May be this should be moved under the nvidia,io-rail-voltage description?
> +All above IO pads supports the deep power down state.
May be this should be moved under the nvidia,io-pad-deep-power-down
description?
> +Example:
> + #include <dt-bindings/pinctrl/pinctrl-tegra210-io-pad.h>
> + pmc@0,7000e400 {
> + pmc-pad-control {
> + compatible = "nvidia,tegra210-io-pad";
> + pinctrl-names = "default";
> + pinctrl-0 = <&tegra_io_pad_volt_default>;
> + tegra_io_pad_volt_default: common {
> + audio {
> + pins = "audio";
> + nvidia,io-pad-deep-power-down = <TEGRA210_IO_PAD_DEEP_POWER_DOWN_DISABLE>;
> + };
> + audio-hv {
> + pins = "audio-hv";
> + nvidia,io-rail-voltage = <TEGRA210_IO_RAIL_1800000UV>;
> + };
> + gpio {
> + pins = "gpio";
> + nvidia,io-rail-voltage = <TEGRA210_IO_RAIL_1800000UV>;
> + };
> + rest {
> + pins = "dmic", "sdmmc1", "sdmmc3";
> + nvidia,io-rail-voltage = <TEGRA210_IO_RAIL_1800000UV>;
> + };
I know this is an example, but it does not make sense to me why audio-hv
and gpio and separated from 'rest' when they have the same configuration.
Cheers
Jon
--
To unsubscribe from this list: send the line "unsubscribe linux-tegra" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
