On 01/23/2015 10:34 AM, Mark Rutland wrote:
On Fri, Jan 23, 2015 at 04:57:19PM +0000, Stephen Warren wrote:
On 01/23/2015 04:31 AM, Paul Walmsley wrote:
+ Arto, Terje for comments on the host1x section
+ Stephen Warren for comments on the serial DT data
On Wed, 21 Jan 2015, Mark Rutland wrote:
As mentioned in my reply to the DT list patch [1], there are a couple of
bits I'd like to see cleaned up first, but in the meantime I have some
comments from my first pass of the dtsi below. Some of these may equally
apply to existing dts(i) files.
I see a few undocumented compatible strings (at least when comparing
against mainline). If there are other series or trees I should be
looking at, any pointers would be appreciated. If not, documentation
updates would be nice (checkpatch should complain otherwise).
On Fri, Jan 16, 2015 at 11:45:29AM +0000, Paul Walmsley wrote:
Add an initial device tree file for the Tegra132 SoC. The DT file is
based on arch/arm/boot/dts/tegra124.dtsi and
arch/arm/boot/dts/tegra114.dtsi, with the following significant
changes:
- Tegra132 uses a Denver CPU cluster rather than an ARMv7 CPU cluster
- Devices are arranged by bus, rather than in a flat topology
- No polling delays have been defined for the thermal zones. I don't
believe that this is a property of the SoC hardware, but rather of a
given use-case.
diff --git a/arch/arm64/boot/dts/tegra/tegra132.dtsi b/arch/arm64/boot/dts/tegra/tegra132.dtsi
+ /*
+ * There are two serial drivers: an 8250 based simple
+ * serial driver and an APB DMA based serial driver
+ * for higher baudrate and performance. To enable the
+ * 8250 based driver, the compatible string is
+ * "nvidia,tegra132-uart", "nvidia,tegra124-uart",
+ * "nvidia,tegra20-uart" and to enable the APB DMA
+ * based serial driver, the compatible string is
+ * "nvidia,tegra132-hsuart", "nvidia,tegra124-hsuart",
+ * "nvidia,tegra30-hsuart".
+ */
Is there any reason to continue with this split?
Surely if the only difference is DMA, the presence of dmas and dma-names
should be sufficient to get the driver to do the right thing, and if you
need to disable DMA for debugging that could be a command-line option.
I vaguely recall asking for the DMA support to be integrated into the
regular 8250 driver instead when the separate DMA-capable driver was
first added. I /think/ there was resistance to this because adding lots
of different SoC-specific ways to do DMA into the existing 8250 driver
would complicate it even more, and hence be unmaintainable.
I assume that reasoning is still valid.
Perhaps what we need is more fine-grained driver selection, not just
based on compatible value. Something like:
if compatible == nvidia,tegra20-uart:
if node.has_prop("enable-dma"):
driver = Tegra-specfic DMA capable UART driver
else:
driver = Common 8250 driver
Surely we should assume that if the DMAs are listed (and not disabled)
they are usable?
I would assume so, yes.
> I'm not sure I see the point in an additional property
to force Linux-internal driver selection in this way.
I think it comes down to whether you want to use DMA for that UART or
not. I don't recall the exact reason why this might be important.
Perhaps it's one/more of:
- The Tegra-specific DMA-capable driver can't be used for early debug
but the core 8250 driver can. I don't know if this is true though.
- There are a limited number of DMA channels on Tegra. If all ports
blindly used DMA simply because the dmas property was included, then
we'd risk running out of DMA channels for cases where it absolutely had
to be used; e.g. a low-volume debug console might prevent a high-volume
MODEM or BT UART from using DMA if they probed in the "wrong" order.
Laxman might be able to shed more light on this.
What happens if we have a driver for a particular string, but fail to
probe? Can we fall back to a more generic driver?
At least in this case, I'd assume so, yes.
Is that something that of_serial.c could/should be enhanced to do? That
said, the whole reasoning behind separate compatible properties before
was that compatible is supposed to "drive" driver selection. At least,
that's what I was told then.
The compatible string is meant to describe the programming interface the
device is compatible with. The kernel should then choose the most
appropriate driver it knows can handle that HW programming interface.
Considering it as a way to choose the driver is backwards. I'd expect
the device node to have both strings (with the DMA capable string first)
unless it really doesn't have any DMAs.
That's a subtly different interpretation of DT compatible usage than was
given (I think it was by Mitch Bradley???) when this driver was
introduced. In the conversation then, it was asserted that using
different compatible values to describe that SW should use a different
interface to the HW (non-DMA vs. DMA) was exactly in line with the
semantic concept of compatible.
--
To unsubscribe from this list: send the line "unsubscribe linux-tegra" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
