On Fri, Oct 31, 2014 at 9:41 AM, Andrew Bresticker
<abrestic@xxxxxxxxxxxx> wrote:
> On Fri, Oct 31, 2014 at 4:32 AM, Thierry Reding
> <thierry.reding@xxxxxxxxx> wrote:
>> On Thu, Oct 30, 2014 at 10:26:47AM -0700, Andrew Bresticker wrote:
>>> On Thu, Oct 30, 2014 at 10:24 AM, Thierry Reding
>>> <thierry.reding@xxxxxxxxx> wrote:
>>> > On Thu, Oct 30, 2014 at 10:19:21AM -0700, Andrew Bresticker wrote:
>>> >> On Thu, Oct 30, 2014 at 6:55 AM, Thierry Reding
>>> >> <thierry.reding@xxxxxxxxx> wrote:
>>> >> > On Wed, Oct 29, 2014 at 09:37:14AM -0700, Andrew Bresticker wrote:
>>> >> >> On Wed, Oct 29, 2014 at 2:43 AM, Thierry Reding
>>> >> >> <thierry.reding@xxxxxxxxx> wrote:
>>> >> >> > On Tue, Oct 28, 2014 at 03:27:50PM -0700, Andrew Bresticker wrote:
>>> >> >> > [...]
>>> >> >> >> diff --git a/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-xusb-padctl.txt b/Documentation/devicetree/bindings/pinctrl/nvidia,tegra124-xusb-padctl.txt
>>> >> >> > [...]
>>> >> >> >> +Optional properties:
>>> >> >> >> +-------------------
>>> >> >> >> +- vbus-{0,1,2}-supply: VBUS regulator for the corresponding UTMI pad.
>>> >> >> >> +- vddio-hsic-supply: VDDIO regulator for the HSIC pads.
>>> >> >> >> +- nvidia,usb3-port-{0,1}-lane: PCIe/SATA lane to which the corresponding USB3
>>> >> >> >> + port is mapped. See <dt-bindings/pinctrl/pinctrl-tegra-xusb.h> for the list
>>> >> >> >> + of valid values.
>>> >> >> >
>>> >> >> > I dislike how we now need to provide a list of all pins in the header
>>> >> >> > file, where previously we used strings for this. This could become very
>>> >> >> > ugly if the set of pins changes in future generations of this IP block.
>>> >> >> >
>>> >> >> > Could we instead derive this from the pinmux nodes? For example you have
>>> >> >> > this in the example below:
>>> >> >> >
>>> >> >> > usb3p0 {
>>> >> >> > nvidia,lanes = "pcie-0";
>>> >> >> > ...
>>> >> >> > };
>>> >> >> >
>>> >> >> > Perhaps what we need is to either key off the node name or add another
>>> >> >> > property, such as:
>>> >> >> >
>>> >> >> > nvidia,usb3-port = <0>;
>>> >> >> >
>>> >> >> > This would match the nvidia,usb2-port property that you've added below.
>>> >> >>
>>> >> >> That is actually how I described the USB3 port to SS lane mapping
>>> >> >> originally, but in review of an earlier version of this series,
>>> >> >> Stephen suggested that I make it a separate, not pinconfig property
>>> >> >> since it wasn't a value written directly to the hardware. I'm fine
>>> >> >> with changing it back as the pinconfig property makes more sense to me
>>> >> >> as well.
>>> >> >
>>> >> > Hmm... I had considered it a mux option of the specific lane. If the
>>> >> > function is usb3, it'd still need to be muxed to one of the ports. So
>>> >> > it's additional information associated with the usb3 function.
>>> >> >
>>> >> > I did look through the driver changes and can't really make out which
>>> >> > part of the code actually performs this assignment. Can you point me to
>>> >> > it?
>>> >>
>>> >> There's not really an assignment. The property is used to map between
>>> >> a lane (e.g. PCIe-0 or SATA) and the USB3.0 port it's mapped to. For
>>> >> an example of where it's used, take a look at usb3_phy_power_on().
>>> >> There are certain per-lane registers which need to be programmed in
>>> >> addition to the per-USB3.0 port pad registers. This mapping is used
>>> >> to determine which lane needs to be programmed.
>>> >
>>> > Are you saying the mapping of lane to USB port is fixed? That is, PCIe-0
>>> > lane is always used for USB port X and SATA always for USB port Y?
>>>
>>> No, sorry if that was unclear, it's not fixed - it's a board specific
>>> property.
>>
>> Okay, but there's no register that contains the mapping of the port to a
>> lane, similar to what's done for the functions, right?
>
> Correct.
>
>> I mean the driver only uses the lane to find out which register to write.
>> Doesn't that imply that two lanes (or more) could be mapped to the same
>> USB 3.0 port?
>
> I guess? Not sure how that would work in hardware to have two
> SuperSpeed lanes wired up to a single port.
>
>> I'm not sure I'm being clear here, so let me try another way. In order
>> to establish a mapping between USB port and lane, I would've expected
>> one of the following to happen:
>>
>> - A value derived from the lane number is written to a register
>> belonging to a given port.
>>
>> - A value derived from the port number is written to a register
>> belonging to a given lane.
>>
>> I can't see the code do either of the above, which to me implies that
>> there's a fixed mapping between lanes and ports. What am I missing?
>
> It's fixed in that it's not a software-modifiable property. It's
> describing an electrical connection between lane and port. For
> example, it's possible that one board has PCIe lane 1 wired up to
> SuperSpeed port 1 and on another board for the SATA lane to be wired
> up to SuperSpeed port 1. Does that make sense?
So what's the verdict here?
--
To unsubscribe from this list: send the line "unsubscribe linux-tegra" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
