On Mon, Sep 15, 2014 at 11:09 AM, Stephen Warren <swarren@xxxxxxxxxxxxx> wrote: > On 09/15/2014 11:06 AM, Andrew Bresticker wrote: >> >> On Mon, Sep 15, 2014 at 12:00 AM, Tomeu Vizoso <tomeu@xxxxxxxxxxxxxxx> >> wrote: >>> >>> On 12 September 2014 18:37, Andrew Bresticker <abrestic@xxxxxxxxxxxx> >>> wrote: >>>> >>>> On Tue, Sep 9, 2014 at 1:21 AM, Tomeu Vizoso <tomeu@xxxxxxxxxxxxxxx> >>>> wrote: >>>>> >>>>> On 8 September 2014 18:22, Andrew Bresticker <abrestic@xxxxxxxxxxxx> >>>>> wrote: >>>>>> >>>>>> On Mon, Sep 8, 2014 at 8:34 AM, Tomeu Vizoso <tomeu@xxxxxxxxxxxxxxx> >>>>>> wrote: >>>>>>> >>>>>>> On 2 September 2014 23:34, Andrew Bresticker <abrestic@xxxxxxxxxxxx> >>>>>>> wrote: >>>>>>>> >>>>>>>> >>>>>>>> Tested on Venice2, Jetson TK1, and Big with a variety of USB2.0 and >>>>>>>> USB3.0 memory sticks and ethernet dongles using controller firmware >>>>>>>> recently posted by Andrew Chew [2]. >>>>>>> >>>>>>> >>>>>>> I have had mixed results when testing this on a Jetson TK1 board. Of >>>>>>> 8 >>>>>>> USB devices I tested with, about half where probed correctly, but the >>>>>>> other half repeatedly fail in hub_port_init because in the GET_STATUS >>>>>>> right after the reset, the C_PORT_CONNECTION bit is set. >>>>>>> >>>>>>> I don't see any correlation between the failure and the kind of usb >>>>>>> device, but I don't have much experience with USB implementations >>>>>>> either. >>>>>> >>>>>> >>>>>> Hmm... I haven't seen that before. Which particular devices were you >>>>>> using? >>>>> >>>>> >>>>> Here they are: >>>>> >>>>> work: >>>>> >>>>> Genius keyboard: 05d5:6782 >>>>> Logitech mouse: 046d:c06a >>>>> Denver MP3 player: 10d6:1100 >>>>> Atheros Bluetooth dongle: 0cf3:3005 >>>>> >>>>> don't work: >>>>> >>>>> MCS7830 ethernet dongle: 9710:7830 >>>>> Genesys Logic hub: 05e3:0608 >>>> >>>> >>>> I tried the hub and it works just fine for me... Have you tried this >>>> on any other boards like Big or Blaze? >>> >>> >>> I have a Blaze here, but haven't been able to get the external ports >>> to power up. I don't have schematics nor a strong interest to get that >>> fixed myself, as I can test my code just fine with the Blaze's >>> internal camera and the devices that do work on the Jetson. >> >> >> Ok, since Blaze has been announced, hopefully we can post a >> device-tree for it soon. >> >>> I'm using the firmware file that was posted recently: >>> >>> xhci-tegra 70090000.usb: Firmware timestamp: 2014-05-02 02:22:50 UTC, >>> Falcon state 0x20 >> >> >> Yup, I'm using the same firmware. >> >>> If things work for you with the same sources, .config and firmware, I >>> can only think of the hw being different (other hw revision?). >> >> >> That, or perhaps bootloader differences? I'm using mainline U-Boot. >> >> Stephen, Thierry, have either of you had a chance to test this series? > > > I haven't had a chance to yet. I just went to try it out, and found that it > depends on a whole slew of other patches that I don't have. Is there a git > branch somewhere to save me having to track down all the dependencies? Yes, Tomeu has the branch he used for testing here: http://cgit.collabora.com/git/user/tomeu/linux.git/log/?h=3.17rc4-xhci You'll also need the firmware Andrew Chew posted: https://patchwork.ozlabs.org/patch/384013/ -- To unsubscribe from this list: send the line "unsubscribe linux-tegra" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
