On Fri, Feb 28, 2014 at 9:28 AM, Lucas Stach <l.stach@xxxxxxxxxxxxxx> wrote:
> The glue around the core designware IP is
> significantly different between the Exynos and
> i.MX, which is reflected in the DT bindings.
>
> Note that this patch doesn't change any bindings,
> but just alters the documentation to match reality
> of deployed DTs and kernels.
>
> Signed-off-by: Lucas Stach <l.stach@xxxxxxxxxxxxxx>
> ---
> .../devicetree/bindings/pci/designware-pcie.txt | 69 +--------------------
> .../devicetree/bindings/pci/fsl,imx6q-pcie.txt | 48 +++++++++++++++
> .../bindings/pci/samsung,exynos5440-pcie.txt | 70 ++++++++++++++++++++++
> 3 files changed, 119 insertions(+), 68 deletions(-)
> create mode 100644 Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
> create mode 100644 Documentation/devicetree/bindings/pci/samsung,exynos5440-pcie.txt
>
> diff --git a/Documentation/devicetree/bindings/pci/designware-pcie.txt b/Documentation/devicetree/bindings/pci/designware-pcie.txt
> index d6fae13ff062..8274c80fe874 100644
> --- a/Documentation/devicetree/bindings/pci/designware-pcie.txt
> +++ b/Documentation/devicetree/bindings/pci/designware-pcie.txt
> @@ -1,15 +1,7 @@
> * Synopsys Designware PCIe interface
>
> Required properties:
> -- compatible: should contain "snps,dw-pcie" to identify the
> - core, plus an identifier for the specific instance, such
> - as "samsung,exynos5440-pcie" or "fsl,imx6q-pcie".
> -- reg: base addresses and lengths of the pcie controller,
> - the phy controller, additional register for the phy controller.
> -- interrupts: interrupt values for level interrupt,
> - pulse interrupt, special interrupt.
> -- clocks: from common clock binding: handle to pci clock.
> -- clock-names: from common clock binding: should be "pcie" and "pcie_bus".
> +- compatible: should contain "snps,dw-pcie" to identify the core.
> - #address-cells: set to <3>
> - #size-cells: set to <2>
> - device_type: set to "pci"
> @@ -22,62 +14,3 @@ Required properties:
>
> Optional properties:
> - reset-gpio: gpio pin number of power good signal
> -
> -Optional properties for fsl,imx6q-pcie
> -- power-on-gpio: gpio pin number of power-enable signal
> -- wake-up-gpio: gpio pin number of incoming wakeup signal
> -- disable-gpio: gpio pin number of outgoing rfkill/endpoint disable signal
> -
> -Example:
> -
> -SoC specific DT Entry:
> -
> - pcie@290000 {
> - compatible = "samsung,exynos5440-pcie", "snps,dw-pcie";
> - reg = <0x290000 0x1000
> - 0x270000 0x1000
> - 0x271000 0x40>;
> - interrupts = <0 20 0>, <0 21 0>, <0 22 0>;
> - clocks = <&clock 28>, <&clock 27>;
> - clock-names = "pcie", "pcie_bus";
> - #address-cells = <3>;
> - #size-cells = <2>;
> - device_type = "pci";
> - ranges = <0x00000800 0 0x40000000 0x40000000 0 0x00001000 /* configuration space */
> - 0x81000000 0 0 0x40001000 0 0x00010000 /* downstream I/O */
> - 0x82000000 0 0x40011000 0x40011000 0 0x1ffef000>; /* non-prefetchable memory */
> - #interrupt-cells = <1>;
> - interrupt-map-mask = <0 0 0 0>;
> - interrupt-map = <0x0 0 &gic 53>;
> - num-lanes = <4>;
> - };
> -
> - pcie@2a0000 {
> - compatible = "samsung,exynos5440-pcie", "snps,dw-pcie";
> - reg = <0x2a0000 0x1000
> - 0x272000 0x1000
> - 0x271040 0x40>;
> - interrupts = <0 23 0>, <0 24 0>, <0 25 0>;
> - clocks = <&clock 29>, <&clock 27>;
> - clock-names = "pcie", "pcie_bus";
> - #address-cells = <3>;
> - #size-cells = <2>;
> - device_type = "pci";
> - ranges = <0x00000800 0 0x60000000 0x60000000 0 0x00001000 /* configuration space */
> - 0x81000000 0 0 0x60001000 0 0x00010000 /* downstream I/O */
> - 0x82000000 0 0x60011000 0x60011000 0 0x1ffef000>; /* non-prefetchable memory */
> - #interrupt-cells = <1>;
> - interrupt-map-mask = <0 0 0 0>;
> - interrupt-map = <0x0 0 &gic 56>;
> - num-lanes = <4>;
> - };
> -
> -Board specific DT Entry:
> -
> - pcie@290000 {
> - reset-gpio = <&pin_ctrl 5 0>;
> - };
> -
> - pcie@2a0000 {
> - reset-gpio = <&pin_ctrl 22 0>;
> - };
> diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
> new file mode 100644
> index 000000000000..93fbfd62f13c
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
> @@ -0,0 +1,48 @@
> +* Freescale i.MX6 PCIe interface
> +
> +This PCIe host controller is based on the Synopsis Designware PCIe IP
> +and thus inherits all the common properties defined in designware-pcie.txt.
> +
> +Required properties:
> +- compatible: "fsl,imx6q-pcie"
> +- reg: base addresse and length of the pcie controller
> +- interrupts: First entry must contain interrupt handle for controller
> + INTA output.
> +- clocks: Must contain an entry for each entry in clock-names.
> + See ../clocks/clock-bindings.txt for details.
> +- clock-names: Must include the following entries:
> + - "pcie_ref_125m"
> + - "sata_ref_100m"
> + - "lvds_gate"
> + - "pcie_axi"
> +
> +Optional properties:
> +- power-on-gpio: gpio pin number of power-enable signal
> +- wake-up-gpio: gpio pin number of incoming wakeup signal
> +- disable-gpio: gpio pin number of outgoing rfkill/endpoint disable signal
> +
> +Example:
> +
> + pcie@0x01000000 {
> + compatible = "fsl,imx6q-pcie", "snps,dw-pcie";
> + reg = <0x01ffc000 0x4000>;
> + #address-cells = <3>;
> + #size-cells = <2>;
> + device_type = "pci";
> + ranges = <0x00000800 0 0x01f00000 0x01f00000 0 0x00080000
> + 0x81000000 0 0 0x01f80000 0 0x00010000
> + 0x82000000 0 0x01000000 0x01000000 0 0x00f00000>;
> + num-lanes = <1>;
> +
> + interrupts = <0 123 0x04>;
Lucas,
I'm still trying to understand DT interrupt specification and mapping.
Should this be:
interrupts = <0 123 IRQ_TYPE_LEVEL_HIGH>
It seems there is a lot of mixed use of numbers vs defines from
linux/include/dt-bindings in dts files for both gpio and interrupt
levels.
Thanks,
Tim
> +
> + #interrupt-cells = <1>;
> + interrupt-map-mask = <0 0 0 0x7>;
> + interrupt-map = <0 0 0 1 &intc GIC_SPI 123 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 2 &intc GIC_SPI 122 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 3 &intc GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>,
> + <0 0 0 4 &intc GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>;
> +
> + clocks = <&clks 189>, <&clks 187>, <&clks 206>, <&clks 144>;
> + clock-names = "pcie_ref_125m", "sata_ref_100m", "lvds_gate", "pcie_axi";
> + };
> diff --git a/Documentation/devicetree/bindings/pci/samsung,exynos5440-pcie.txt b/Documentation/devicetree/bindings/pci/samsung,exynos5440-pcie.txt
> new file mode 100644
> index 000000000000..0b4de1014876
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pci/samsung,exynos5440-pcie.txt
> @@ -0,0 +1,70 @@
> +* Samsung Exynos 5440 PCIe interface
> +
> +This PCIe host controller is based on the Synopsis Designware PCIe IP
> +and thus inherits all the common properties defined in designware-pcie.txt.
> +
> +Required properties:
> +- compatible: "samsung,exynos5440-pcie"
> +- reg: base addresses and lengths of the pcie controller,
> + the phy controller, additional register for the phy controller.
> +- interrupts: A list of interrupt outputs for level interrupt,
> + pulse interrupt, special interrupt.
> +- clocks: Must contain an entry for each entry in clock-names.
> + See ../clocks/clock-bindings.txt for details.
> +- clock-names: Must include the following entries:
> + - "pcie"
> + - "pcie_bus"
> +
> +Example:
> +
> +SoC specific DT Entry:
> +
> + pcie@290000 {
> + compatible = "samsung,exynos5440-pcie", "snps,dw-pcie";
> + reg = <0x290000 0x1000
> + 0x270000 0x1000
> + 0x271000 0x40>;
> + interrupts = <0 20 0>, <0 21 0>, <0 22 0>;
> + clocks = <&clock 28>, <&clock 27>;
> + clock-names = "pcie", "pcie_bus";
> + #address-cells = <3>;
> + #size-cells = <2>;
> + device_type = "pci";
> + ranges = <0x00000800 0 0x40000000 0x40000000 0 0x00001000 /* configuration space */
> + 0x81000000 0 0 0x40001000 0 0x00010000 /* downstream I/O */
> + 0x82000000 0 0x40011000 0x40011000 0 0x1ffef000>; /* non-prefetchable memory */
> + #interrupt-cells = <1>;
> + interrupt-map-mask = <0 0 0 0>;
> + interrupt-map = <0 0 0 0 &gic GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
> + num-lanes = <4>;
> + };
> +
> + pcie@2a0000 {
> + compatible = "samsung,exynos5440-pcie", "snps,dw-pcie";
> + reg = <0x2a0000 0x1000
> + 0x272000 0x1000
> + 0x271040 0x40>;
> + interrupts = <0 23 0>, <0 24 0>, <0 25 0>;
> + clocks = <&clock 29>, <&clock 27>;
> + clock-names = "pcie", "pcie_bus";
> + #address-cells = <3>;
> + #size-cells = <2>;
> + device_type = "pci";
> + ranges = <0x00000800 0 0x60000000 0x60000000 0 0x00001000 /* configuration space */
> + 0x81000000 0 0 0x60001000 0 0x00010000 /* downstream I/O */
> + 0x82000000 0 0x60011000 0x60011000 0 0x1ffef000>; /* non-prefetchable memory */
> + #interrupt-cells = <1>;
> + interrupt-map-mask = <0 0 0 0>;
> + interrupt-map = <0 0 0 0 &gic GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>;
> + num-lanes = <4>;
> + };
> +
> +Board specific DT Entry:
> +
> + pcie@290000 {
> + reset-gpio = <&pin_ctrl 5 0>;
> + };
> +
> + pcie@2a0000 {
> + reset-gpio = <&pin_ctrl 22 0>;
> + };
> --
> 1.8.5.3
>
--
To unsubscribe from this list: send the line "unsubscribe linux-tegra" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
