On Mon, Jul 15, 2013 at 06:57:27PM +0200, Jean Delvare wrote:
> Hi Wei, Guenter,
>
> On Fri, 12 Jul 2013 15:48:05 +0800, Wei Ni wrote:
> > Add bit defines for the status register.
>
> Regarding the subject: for me these are constants, not macros. AFAIK
> the term "macro" refers to defines with parameters only.
>
> > Signed-off-by: Wei Ni <wni@xxxxxxxxxx>
> > ---
> > drivers/hwmon/lm90.c | 72 ++++++++++++++++++++++++++++++++++----------------
> > 1 file changed, 49 insertions(+), 23 deletions(-)
> >
> > diff --git a/drivers/hwmon/lm90.c b/drivers/hwmon/lm90.c
> > index 5f30f90..c90037f 100644
> > --- a/drivers/hwmon/lm90.c
> > +++ b/drivers/hwmon/lm90.c
> > @@ -179,6 +179,19 @@ enum chips { lm90, adm1032, lm99, lm86, max6657, max6659, adt7461, max6680,
> > #define LM90_HAVE_TEMP3 (1 << 6) /* 3rd temperature sensor */
> > #define LM90_HAVE_BROKEN_ALERT (1 << 7) /* Broken alert */
> >
> > +/* LM90 status */
> > +#define LM90_STATUS_LTHRM (1 << 0) /* local THERM limit tripped */
> > +#define LM90_STATUS_RTHRM (1 << 1) /* remote THERM limit tripped */
> > +#define LM90_STATUS_OPEN (1 << 2) /* remote is an open circuit */
> > +#define LM90_STATUS_RLOW (1 << 3) /* remote low temp limit tripped */
> > +#define LM90_STATUS_RHIGH (1 << 4) /* remote high temp limit tripped */
> > +#define LM90_STATUS_LLOW (1 << 5) /* local low temp limit tripped */
> > +#define LM90_STATUS_LHIGH (1 << 6) /* local high temp limit tripped */
> > +#define LM90_STATUS_BUSY (1 << 7) /* ADC is converting */
>
> LM90_STATUS_BUSY is never used anywhere so please don't define it.
>
> > +
> > +#define MAX6696_STATUS2_RLOW (1 << 3) /* remote2 low temp limit tripped */
> > +#define MAX6696_STATUS2_RHIGH (1 << 4) /* remote2 high temp limit tripped */
> > +
> > /*
> > * Driver data (common to all clients)
> > */
> > @@ -1417,6 +1430,36 @@ static void lm90_init_client(struct i2c_client *client)
> > i2c_smbus_write_byte_data(client, LM90_REG_W_CONFIG1, config);
> > }
> >
> > +static bool lm90_is_tripped(struct i2c_client *client)
> > +{
> > + struct lm90_data *data = i2c_get_clientdata(client);
> > + u8 status, status2 = 0;
> > +
> > + lm90_read_reg(client, LM90_REG_R_STATUS, &status);
> > +
> > + if (data->kind == max6696)
> > + lm90_read_reg(client, MAX6696_REG_R_STATUS2, &status2);
> > +
> > + if ((status & 0x7f) == 0 && (status2 & 0xfe) == 0)
> > + return false;
>
> It's a bit disappointing to not use the freshly introduced constants.
> That being said I agree it would make the code hard to read, so you can
> leave it as is.
>
> Unrelated to this patch, but Guenter, I am worried about the MAX6696
> handling here. I realize that I am the one who accepted your code, but
> now it looks wrong. Specifically:
> * We check for (status2 & 0xfe) i.e. 7 alarm bits, but the code below
> only reports 2 alarms bits. So if any of the 5 other alarm bits in
> STATUS2 are, we may return true (chip is tripped) but not print the
> cause.
> * At least bits 1 and 2 of STATUS 2 fit totally fine in the driver as
> it currently exists, so I can't think of any reason for not handling
> them. Why are we not? Ideally we should print a message for every
> alarm bit so that we never return "true" without printing a message.
> Even though OT2 limits aren't handled by the driver...
> * If you think this piece of code shouldn't deal with OT/THERM limits
> because they do not trigger an SMBus alarm, this can be discussed,
> but all chips should be handled the same in this respect then.
> * Why in the first place is max6696's data->alert_alarms set to 0x187c
> and not 0x1c7c? Including 1OPEN but not 2OPEN makes no sense.
>
I am about to leave for vacation, so this will have to wait for a couple of
weeks. I'll look at it after I am back.
Guenter
> > +
> > + if (status & (LM90_STATUS_LLOW | LM90_STATUS_LHIGH | LM90_STATUS_LTHRM))
> > + dev_warn(&client->dev,
> > + "temp%d out of range, please check!\n", 1);
> > + if (status & (LM90_STATUS_RLOW | LM90_STATUS_RHIGH | LM90_STATUS_RTHRM))
> > + dev_warn(&client->dev,
> > + "temp%d out of range, please check!\n", 2);
> > + if (status & LM90_STATUS_OPEN)
> > + dev_warn(&client->dev,
> > + "temp%d diode open, please check!\n", 2);
> > +
> > + if (status2 & (MAX6696_STATUS2_RLOW | MAX6696_STATUS2_RHIGH))
> > + dev_warn(&client->dev,
> > + "temp%d out of range, please check!\n", 3);
> > +
> > + return true;
> > +}
> > +
> > static int lm90_probe(struct i2c_client *client,
> > const struct i2c_device_id *id)
> > {
> > @@ -1515,36 +1558,19 @@ static int lm90_remove(struct i2c_client *client)
> >
> > static void lm90_alert(struct i2c_client *client, unsigned int flag)
> > {
> > - struct lm90_data *data = i2c_get_clientdata(client);
> > - u8 config, alarms, alarms2 = 0;
> > -
> > - lm90_read_reg(client, LM90_REG_R_STATUS, &alarms);
> > -
> > - if (data->kind == max6696)
> > - lm90_read_reg(client, MAX6696_REG_R_STATUS2, &alarms2);
> > -
> > - if ((alarms & 0x7f) == 0 && (alarms2 & 0xfe) == 0) {
> > + if (!lm90_is_tripped(client)) {
>
> You could swap the success and failure cases to avoid this negation.
>
> > dev_info(&client->dev, "Everything OK\n");
> > } else {
> > - if (alarms & 0x61)
> > - dev_warn(&client->dev,
> > - "temp%d out of range, please check!\n", 1);
> > - if (alarms & 0x1a)
> > - dev_warn(&client->dev,
> > - "temp%d out of range, please check!\n", 2);
> > - if (alarms & 0x04)
> > - dev_warn(&client->dev,
> > - "temp%d diode open, please check!\n", 2);
> > -
> > - if (alarms2 & 0x18)
> > - dev_warn(&client->dev,
> > - "temp%d out of range, please check!\n", 3);
> > -
> > /*
> > * Disable ALERT# output, because these chips don't implement
> > * SMBus alert correctly; they should only hold the alert line
> > * low briefly.
> > */
> > + struct lm90_data *data = i2c_get_clientdata(client);
> > + u8 config, alarms;
> > +
> > + lm90_read_reg(client, LM90_REG_R_STATUS, &alarms);
>
> You end up reading LM90_REG_R_STATUS, which is not OK. This register
> contains self-clearing bits, so there is no guarantee that the second
> read will return the same value as the first read. You'll have to come
> up with a different approach that reads LM90_REG_R_STATUS only once.
>
> > +
> > if ((data->flags & LM90_HAVE_BROKEN_ALERT)
> > && (alarms & data->alert_alarms)) {
> > dev_dbg(&client->dev, "Disabling ALERT#\n");
>
>
> --
> Jean Delvare
>
--
To unsubscribe from this list: send the line "unsubscribe linux-tegra" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
