On 10/11/2012 03:15 AM, Joseph Lo wrote:
> On Wed, 2012-10-10 at 06:38 +0800, Stephen Warren wrote:
>> On 10/08/2012 04:26 AM, Joseph Lo wrote:
>>> This supports power-gated (LP2) idle on secondary CPUs for Tegra30.
>>> The secondary CPUs can go into LP2 state independently. When CPU goes
>>> into LP2 state, it saves it's state and puts itself to flow controlled
>>> WFI state. After that, it will been power gated.
>>
>>> diff --git a/arch/arm/mach-tegra/cpuidle-tegra30.c b/arch/arm/mach-tegra/cpuidle-tegra30.c
>>
>>> static struct cpuidle_driver tegra_idle_driver = {
>>> .name = "tegra_idle",
>>> .owner = THIS_MODULE,
>>> .en_core_tk_irqen = 1,
>>> - .state_count = 1,
>>> + .state_count = 2,
>>
>> Doesn't that assignment need to be ifdef'd just like the array entry
>> setup below:
>>
>>> .states = {
>>> [0] = ARM_CPUIDLE_WFI_STATE_PWR(600),
>>> +#ifdef CONFIG_PM_SLEEP
>>> + [1] = {
>>> + .enter = tegra30_idle_lp2,
>>> + .exit_latency = 2000,
>>> + .target_residency = 2200,
>>> + .power_usage = 0,
>>> + .flags = CPUIDLE_FLAG_TIME_VALID,
>>> + .name = "LP2",
>>> + .desc = "CPU power-gate",
>>> + },
>>> +#endif
>>> },
>>> };
>>
>>> @@ -41,6 +114,10 @@ int __init tegra30_cpuidle_init(void)
>>> struct cpuidle_device *dev;
>>> struct cpuidle_driver *drv = &tegra_idle_driver;
>>>
>>> +#ifndef CONFIG_PM_SLEEP
>>> + drv->state_count = 1; /* support clockgating only */
>>> +#endif
>>
>> Oh, I see it's done here. Just fixing the static initialization seems a
>> lot simpler?
>>
> OK. Will do.
>
>>> diff --git a/arch/arm/mach-tegra/pm.c b/arch/arm/mach-tegra/pm.c
>>
>>> +void __cpuinit tegra_clear_cpu_in_lp2(int cpu)
>>> +{
>>> + spin_lock(&tegra_lp2_lock);
>>> + BUG_ON(!cpumask_test_cpu(cpu, &tegra_in_lp2));
>>> + cpumask_clear_cpu(cpu, &tegra_in_lp2);
>>> +
>>> + /*
>>> + * Update the IRAM copy used by the reset handler. The IRAM copy
>>> + * can't use used directly by cpumask_clear_cpu() because it uses
>>> + * LDREX/STREX which requires the addressed location to be inner
>>> + * cacheable and sharable which IRAM isn't.
>>> + */
>>> + writel(tegra_in_lp2.bits[0], tegra_cpu_lp2_mask);
>>> + dsb();
>>
>> Why not /just/ store the data in IRAM, and read/write directly to it,
>> rather than maintaining an SDRAM-based copy of it?
>>
>> Then, wouldn't the body of this function be simply:
>>
>> spin_lock();
>> BUG_ON(!(tegra_cpu_lp2_mask & BIT(cpu)));
>> tegra_cpu_lp2_mask |= BIT(cpu);
>> spin_unlock();
>>
>
> It may not simple like this. To maintain it identical to a cpumask. It
> may look likes below. Because I need to compare it with cpu_online_mask.
Oh, the comparison against cpu_online_mask() is what I was missing. I
guess that offline CPUs don't go into LP2, so you can't just check that
tegra_cpu_lp2_mask == (1 << num_cpus()) - 1.
One way to avoid that might be to maintain a cpu_in_lp2_count variable
alongside the mask, and simply compare that against num_online_cpus()
rather than comparing the two masks. At least that would avoid the
following line:
>>> + writel(tegra_in_lp2.bits[0], tegra_cpu_lp2_mask);
... making use of knowledge of the internal structure of the struct
cpumask type.
However, given the comparison requirement, either way is probably fine.
--
To unsubscribe from this list: send the line "unsubscribe linux-tegra" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
