Re: [RFC][PATCH v3 1/3] runtime interpreted power sequences

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 07/31/2012 06:13 PM, Thierry Reding wrote:
I don't see any need for microseconds myself - anybody sees use for
finer-grained delays?

Btw, I noticed I was using mdelay instead of msleep - caught and fixed that.

You might want to take a look at Documentation/timers/timers-howto.txt.
msleep() isn't very accurate for periods shorter than 20 ms.

Ok, looks like usleep_range is the way to go here. In that case it would probably not hurt to specify delays in microseconds in the DT and platform data as well.

+Device tree
+-----------
+All the same, power sequences can be encoded as device tree nodes. The following
+properties and nodes are equivalent to the platform data defined previously:
+
+               power-supply = <&mydevice_reg>;
+               enable-gpio = <&gpio 6 0>;
+
+               power-on-sequence {
+                       regulator@0 {
+                               id = "power";

Is there a reason not to put the phandle here, like:

                                    id = <&mydevice_reg>;

(or maybe 'device' instead of id?)

There is one reason, but it might be a bad one. On Tegra, PWM
phandle uses an extra cell to encode the duty-cycle the PWM should
have when we call get_pwm().

This is not only the case on Tegra, but it is the default unless a
driver specifically overrides it. The second cell specifies the index of
the PWM device within the PWM chip.  The third cell doesn't specify the
duty cycle but the period of the PWM.

Then I think there is a mistake in Documentation/devicetree/bindings/pwm/nvidia,tegra20-pwm.txt:

"the second cell is the duty cycle in nanoseconds."

This makes it possible to address the
same PWM with different phandles (and different duty cycles),

How so? A phandle will always refer to a PWM chip. Paired with the
second cell, of_pwm_request() will resolve that into the correct PWM
device.

For tegra, we can only address PWMs this way IIRC:

pwm = <&pwm 2 5000000>;

If we had <&pwm 2>, I agree that there would be no problem. But here the period of the PWM is also given - and in practice, we can request the same PWM using different phandles. For instance, if the above property was part of the power-on sequence, and the following

pwm = <&pwm 2 0>;

was part of power-off, how can I know that these two different phandles refer to the same PWM without calling pwm_get a second time and getting -EBUSY?

Of course if the same period is specified for both, I will not have this issue as the phandles will be identical, but the possibility remains open that we are given a faulty tree here.

More generally speaking, wouldn't it make more sense to have the period/duty cycle of a PWM encoded into separate properties when needed and have the phandle just reference the PWM instance? This also seems to stand from an API point of view, since the period is not specified when invoking pwm_request or pwm_get, but set by its own pwm_set_period function?

On an unrelated note, I also don't understand why the period is also a parameter of pwm_config and why pwm_set_period does not do anything beyond setting a struct member that is returned by pwm_get_period (but maybe I am missing something here).

Alex.

--
To unsubscribe from this list: send the line "unsubscribe linux-tegra" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html


[Index of Archives]     [ARM Kernel]     [Linux ARM]     [Linux ARM MSM]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]

  Powered by Linux