On Tue, Sep 23, 2014 at 1:31 AM, 席智勇 <xizhiyong18@xxxxxxx> wrote: > > in tgt, i found that, when a lun is created or destroyed, ASC_REPORTED_LUNS_DATA_HAS_CHANGED was add to I_T by > ua_sense_add(), except for command REPORT LUN, > in IET, i do not find the same program logic, > is this the reason why i met the problem when i using tgt, but not when IET? That is very likely and probably why you see this. It is odd that your initiator appears to temporarily drop the capacity to 0 on this >>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.752462] sdd: detected capacity change from 1073807360 to 0 until it has re-issued a new READCAPACITY to re-learn the correct capacity again. I would have imagined that an initiator would have kept the old data until the point it could verify whether the device had actually changed or not. But maybe they have reason for this? But it sounds somewhat odd initiator behaviour. For device startup, when you start tgtd and there are ways to stop the initiator from being able to access any LUNs at all until you have finished setting up everything in TGTD. If you use tgtadm to set up the target and all the LUNs, then if you change your scripts so that you create all the LUNs and all the configuration before allowing any initiators to connect, then I think your initiators will not see these unit attentions. I.e. change the scripts to wait doing this line at the very end when LUN creation has finished : # Allow ALL initiators to connect to this target tgtadm --lld iscsi --mode target --op bind --tid 1 --initiator-address ALL I do not know the corresponding way to do this with tgt-admin since I never use that tool :-( If this only happens when you start the tgt service and you use /etc/init.d/ scripts from your system, you can check in which order the script does these things. I never use the scripts that come from the distros so I don;t know the exact details in which order they do things. regards ronnie sahlberg > > > At 2014-09-22 20:23:27, "席智勇" <xizhiyong18@xxxxxxx> wrote: >>may you give some advise to me about the problem report by me. >> >>-------- Forwarding messages -------- >>From: "席智勇" <xizhiyong18@xxxxxxx> >>Date: 2014-09-22 03:29:51 >>To: "席智勇" <xizhiyong18@xxxxxxx> >>Cc: "ronnie sahlberg" <ronniesahlberg@xxxxxxxxx>,stgt@xxxxxxxxxxxxxxx >>Subject: Reply:Reply:Re: attached devices exported by tgt not oprational >>from the syslog of the initiator side, it seams the sd_revalide_disk was trigged more >>than once, and it succeed first time, when logged "sd 7:0:0:4: [sdf] Attached SCSI disk", >>i don't when and where the sd_revalidate was called again, and it failed when send SCSI >>command TEST_UNIT_READ and RRAD_CAPACITY. >> >> >> >>At 2014-09-11 11:35:57, "席智勇" <xizhiyong18@xxxxxxx> wrote: >>>first of all, thanks for your reply. >>>in my program, it will use 128 LUNS at the most each target, so LUNS id will >>>not outnumber 255. >>> >>>here is some syslog when the problem occur. you can search [sdf] to find some >>>info, like "[sdf] READ CAPACITY(16) failed" or "[sdf] Unit Not Ready", and "sdf: detected capacity change from 9664266240 to 0", >>>"Sense Key : Illegal Request [current]", "Add. Sense: Logical unit not supported" >>>------------------------------------------------------------------------------------------ >>> >>>#:~/tgt_debug$ cat syslog |grep -C 1 -e "sdf\|sd 7:0:0:4" >>> >>>Aug 26 16:02:25 10-120-120-35 kernel: [1144399.426520] sd 7:0:0:4: [sdf] 18875520 512-byte logical blocks: (9.66 GB/9.00 GiB) >>>Aug 26 16:02:25 10-120-120-35 kernel: [1144399.426629] sd 7:0:0:3: [sdd] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA >>>-- >>>Aug 26 16:02:25 10-120-120-35 kernel: [1144399.427236] sd 7:0:0:5: Attached scsi generic sg12 type 0 >>>Aug 26 16:02:25 10-120-120-35 kernel: [1144399.427409] sd 7:0:0:4: [sdf] Write Protect is off >>>Aug 26 16:02:25 10-120-120-35 kernel: [1144399.427414] sd 7:0:0:4: [sdf] Mode Sense: 69 00 00 08 >>>Aug 26 16:02:25 10-120-120-35 kernel: [1144399.427545] sd 7:0:0:5: [sdg] 2097280 512-byte logical blocks: (1.07 GB/1.00 GiB) >>>Aug 26 16:02:25 10-120-120-35 kernel: [1144399.427875] sd 7:0:0:4: [sdf] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA >>>Aug 26 16:02:25 10-120-120-35 kernel: [1144399.427926] scsi 7:0:0:7: Direct-Access IET VIRTUAL-DISK 0001 PQ: 0 ANSI: 5 >>>-- >>>Aug 26 16:02:25 10-120-120-35 kernel: [1144399.443681] sd 7:0:0:5: [sdg] Attached SCSI disk >>>Aug 26 16:02:25 10-120-120-35 kernel: [1144399.458714] sdf: unknown partition table >>>Aug 26 16:02:25 10-120-120-35 kernel: [1144399.460786] sd 7:0:0:4: [sdf] Attached SCSI disk >>>Aug 26 16:02:25 10-120-120-35 kernel: [1144399.476316] sdh: unknown partition table >>>-- >>>Aug 26 16:02:25 10-120-120-35 kernel: [1144399.701790] Add. Sense: Reported luns data has changed >>>Aug 26 16:02:25 10-120-120-35 kernel: [1144399.703810] sd 7:0:0:4: [sdf] Unit Not Ready >>>Aug 26 16:02:25 10-120-120-35 kernel: [1144399.703814] sd 7:0:0:4: [sdf] >>>Aug 26 16:02:25 10-120-120-35 kernel: [1144399.703815] Sense Key : Unit Attention [current] >>>Aug 26 16:02:25 10-120-120-35 kernel: [1144399.703818] sd 7:0:0:4: [sdf] >>>Aug 26 16:02:25 10-120-120-35 kernel: [1144399.703821] Add. Sense: Reported luns data has changed >>>-- >>>Aug 26 16:02:26 10-120-120-35 kernel: [1144400.336478] Add. Sense: Reported luns data has changed >>>Aug 26 16:02:26 10-120-120-35 kernel: [1144400.338547] sd 7:0:0:4: [sdf] Unit Not Ready >>>Aug 26 16:02:26 10-120-120-35 kernel: [1144400.338552] sd 7:0:0:4: [sdf] >>>Aug 26 16:02:26 10-120-120-35 kernel: [1144400.338554] Sense Key : Unit Attention [current] >>>Aug 26 16:02:26 10-120-120-35 kernel: [1144400.338558] sd 7:0:0:4: [sdf] >>>Aug 26 16:02:26 10-120-120-35 kernel: [1144400.338561] Add. Sense: Reported luns data has changed >>>-- >>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.752462] sdd: detected capacity change from 1073807360 to 0 >>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.752987] sd 7:0:0:4: [sdf] Unit Not Ready >>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.752990] sd 7:0:0:4: [sdf] >>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.752991] Sense Key : Unit Attention [current] >>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.752994] sd 7:0:0:4: [sdf] >>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.752997] Add. Sense: Reported luns data has changed >>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.753254] sd 7:0:0:4: Warning! Received an indication that the LUN assignments on this target have changed. The Linux SCSI layer does not automatically remap LUN assignments. >>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.753472] sd 7:0:0:4: Warning! Received an indication that the LUN assignments on this target have changed. The Linux SCSI layer does not automatically remap LUN assignments. >>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.753655] sd 7:0:0:4: Warning! Received an indication that the LUN assignments on this target have changed. The Linux SCSI layer does not automatically remap LUN assignments. >>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.753666] sd 7:0:0:4: [sdf] READ CAPACITY(16) failed >>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.753672] sd 7:0:0:4: [sdf] >>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.753674] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE >>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.753676] sd 7:0:0:4: [sdf] >>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.753677] Sense Key : Unit Attention [current] >>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.753680] sd 7:0:0:4: [sdf] >>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.753682] Add. Sense: Reported luns data has changed >>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.753883] sd 7:0:0:4: Warning! Received an indication that the LUN assignments on this target have changed. The Linux SCSI layer does not automatically remap LUN assignments. >>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.754075] sd 7:0:0:4: Warning! Received an indication that the LUN assignments on this target have changed. The Linux SCSI layer does not automatically remap LUN assignments. >>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.754275] sd 7:0:0:4: Warning! Received an indication that the LUN assignments on this target have changed. The Linux SCSI layer does not automatically remap LUN assignments. >>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.754286] sd 7:0:0:4: [sdf] READ CAPACITY failed >>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.754291] sd 7:0:0:4: [sdf] >>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.754292] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE >>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.754295] sd 7:0:0:4: [sdf] >>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.754296] Sense Key : Unit Attention [current] >>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.754299] sd 7:0:0:4: [sdf] >>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.754301] Add. Sense: Reported luns data has changed >>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.756150] sdf: detected capacity change from 9664266240 to 0 >>>Aug 26 16:02:28 10-120-120-35 kernel: [1144402.756639] sd 7:0:0:5: [sdg] Unit Not Ready >>>-- >>>Aug 26 16:02:29 10-120-120-35 kernel: [1144402.925588] scsi 3:0:0:21: Direct-Access IET VIRTUAL-DISK 0001 PQ: 0 ANSI: 5 >>>Aug 26 16:02:29 10-120-120-35 kernel: [1144402.925959] sd 7:0:0:4: [sdf] 18875520 512-byte logical blocks: (9.66 GB/9.00 GiB) >>>Aug 26 16:02:29 10-120-120-35 kernel: [1144402.926000] sd 3:0:0:21: Attached scsi generic sg59 type 0 >>>-- >>>Aug 26 16:02:29 10-120-120-35 kernel: [1144402.927749] sd 3:0:0:22: [sdbc] 18875520 512-byte logical blocks: (9.66 GB/9.00 GiB) >>>Aug 26 16:02:29 10-120-120-35 kernel: [1144402.927762] sdf: detected capacity change from 0 to 9664266240 >>>Aug 26 16:02:29 10-120-120-35 kernel: [1144402.927843] scsi 3:0:0:23: Direct-Access IET VIRTUAL-DISK 0001 PQ: 0 ANSI: 5 >>>-- >>>Aug 26 16:02:29 10-120-120-35 kernel: [1144403.191743] Add. Sense: Reported luns data has changed >>>Aug 26 16:02:29 10-120-120-35 kernel: [1144403.195776] sd 7:0:0:4: [sdf] Unit Not Ready >>>Aug 26 16:02:29 10-120-120-35 kernel: [1144403.195779] sd 7:0:0:4: [sdf] >>>Aug 26 16:02:29 10-120-120-35 kernel: [1144403.195780] Sense Key : Unit Attention [current] >>>Aug 26 16:02:29 10-120-120-35 kernel: [1144403.195784] sd 7:0:0:4: [sdf] >>>Aug 26 16:02:29 10-120-120-35 kernel: [1144403.195786] Add. Sense: Reported luns data has changed >>>-- >>>Aug 26 16:02:29 10-120-120-35 kernel: [1144403.592427] sd 7:0:0:39: [sdbx] Mode Sense: 69 00 00 08 >>>Aug 26 16:02:29 10-120-120-35 kernel: [1144403.592809] sd 7:0:0:40: Attached scsi generic sg82 type 0 >>>Aug 26 16:02:29 10-120-120-35 kernel: [1144403.594486] sd 7:0:0:39: [sdbx] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA >>>Aug 26 16:02:29 10-120-120-35 kernel: [1144403.594696] sd 7:0:0:40: [sdby] 18875520 512-byte logical blocks: (9.66 GB/9.00 GiB) >>>Aug 26 16:02:29 10-120-120-35 kernel: [1144403.595825] sd 7:0:0:40: [sdby] Write Protect is off >>>Aug 26 16:02:29 10-120-120-35 kernel: [1144403.595831] sd 7:0:0:40: [sdby] Mode Sense: 69 00 00 08 >>>Aug 26 16:02:29 10-120-120-35 kernel: [1144403.596261] sd 7:0:0:40: [sdby] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA >>>Aug 26 16:02:29 10-120-120-35 kernel: [1144403.605687] sdbx: unknown partition table >>>-- >>>Aug 26 16:02:29 10-120-120-35 kernel: [1144403.610455] sd 7:0:0:39: [sdbx] Attached SCSI disk >>>Aug 26 16:02:29 10-120-120-35 kernel: [1144403.613057] sd 7:0:0:40: [sdby] Attached SCSI disk >>>Aug 26 16:02:29 10-120-120-35 kernel: [1144403.617631] sd 3:0:0:13: [sdaf] Warning! Received an indication that the LUN assignments on this target have changed. The Linux SCSI layer does not automatically remap LUN assignments. >>>-- >>>Aug 26 16:02:33 10-120-120-35 kernel: [1144407.432518] md113: unknown partition table >>>Aug 26 16:02:33 10-120-120-35 kernel: [1144407.662356] sd 7:0:0:4: [sdf] Synchronizing SCSI cache >>>Aug 26 16:02:33 10-120-120-35 kernel: [1144407.663163] sd 7:0:0:4: [sdf] >>>Aug 26 16:02:33 10-120-120-35 kernel: [1144407.663167] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE >>>Aug 26 16:02:33 10-120-120-35 kernel: [1144407.663170] sd 7:0:0:4: [sdf] >>>Aug 26 16:02:33 10-120-120-35 kernel: [1144407.663172] Sense Key : Illegal Request [current] >>>Aug 26 16:02:33 10-120-120-35 kernel: [1144407.663175] sd 7:0:0:4: [sdf] >>>Aug 26 16:02:33 10-120-120-35 kernel: [1144407.663178] Add. Sense: Logical unit not supported >>> >>> >>>At 2014-09-11 02:21:59, "ronnie sahlberg" <ronniesahlberg@xxxxxxxxx> wrote: >>>>When you say "many devices" exactly how many are you referring to? >>>>Can you check if this problem you have only occur when you go from 255 >>>>LUNs to something higher? >>>> >>>> >>>>The default LUN addressing scheme only allows LUNs numbered 0 to 255. >>>>To go to higher LUN numbers, which TGTD supports, doe require that you >>>>switch to a different addressing format >>>>and it may be that your initiator can not handle those other modes. >>>> >>>>Often it might look like you have LUNs 0-255 and then there is a jump >>>>to the next LUN which has the number 16640 if the initiator can not >>>>handle addressing modes properly. >>>> >>>> >>>>I do not know how IET does the LUN numbering. >>>> >>>>If you can collect a wireshark trace of iscsiadm --login from both >>>>STGT and IET then I can take a quick look and see if that is the issue >>>>you are facing. >>>> >>>> >>>> >>>>regards >>>>ronnie sahlberg >>>> >>>> >>>>On Mon, Sep 1, 2014 at 11:00 PM, 席智勇 <xizhiyong18@xxxxxxx> wrote: >>>>> >>>>> when i export many block device by tgt , in one single target , this means many exported lun in one target, to another >>>>> machine by iscsi。 >>>>> >>>>> in another machine , attach the devices by open-iscsi。when i wait the >>>>> size of the device attached change from 0 to correct size, i create raid1 with two devices by mdadm。at this time, mdadm report like >>>>> "/dev/sdem is not suitable for this array.", i read the code of mdadm ,that because it cannot open the device。sometime it even report >>>>> "failed to open /dev/** after earlier success - aborting "。 >>>>> >>>>> i do not know whether it's because i used the device when it's not ready yet, or the problem of tgt。 >>>>> >>>>> all the above said happened when many target lun(tgt) created at the same >>>>> time concurrently。it do not happen in nomal time. when i change tgt to iet, it >>>>> do not happen either。 >>>>> >>>>> >>>>> >>>>> tgt version: 1.0.48 >>>>> >>>>> open-iscsi version:iscsiadm version 2.0-873 >>>>> >>>>> linux system: Linux 3.10.40-amd64 GNU/Linux >>>>> >>>>> >>>>> >>>>> >>>>> >>>>> ------------- >>>>> >>>>> Zhiyong Xi -- To unsubscribe from this list: send the line "unsubscribe stgt" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html