Hi Maurits,
That's good to know about scst. I'm going to try stgt a bit more since of course its convenient to use packages in the main distro. Btw, you were asking about how to pass parameters in Pacemaker, its pretty easy. Here's my current resource for this iSCSI target.
primitive res_iSCSILogicalUnit_dfsroots ocf:heartbeat:iSCSILogicalUnit \
params target_iqn="iqn.1999-06.com.myplace:dfs.dfsroots01" lun="1" path="/dev/drbd0" scsi_id="B69577CC4DC049DEBA086217F0F58DA1" scsi_sn="dfsroots01" vendor_id="STGT" product_id="VirtualHD" \
operations $id="res_iSCSILogicalUnit_dfsroots-operations" \
op start interval="0" timeout="10" \
op stop interval="0" timeout="10" \
op monitor interval="10" timeout="10" start-delay="0" \
meta target-role="started"
Regards,
Doug
On May 2, 2013, at 11:59 PM, Maurits van de Lande <M.vandeLande@xxxxxxxxxxxxxxxx> wrote:
> Hello Doug,
>
> Yesterday I switched over to the scst iSCSI target. http://scst.sourceforge.net/ The packages needed to be build from source. I requested ElRepo to add the packages. (there's a kernel module involved)
>
> This is my request:
> http://elrepo.org/bugs/view.php?id=378
>
> I also found some OCF resource agents for pacemaker at:
> http://think-brick.blogspot.nl/2012/03/scst-iscsi-resource-agents-for.html
> I'll test those next week.
>
> Scst works great! I already added the iscsi disk to a Microsoft Failover cluster.
>
>> I just asked the exact same question. I have the same setup and am looking to use this for Microsoft Failover >Clustering. I haven't gotten any responses or seen any other emails on the mailing list thought, I'm wondering if this list is no longer used
>
> I noticed at the drbd users list that if nobody knows the answer then there's no reply at all.
>
> Regards,
>
> Maurits
>
> -----Oorspronkelijk bericht-----
> Van: Doug Clow [mailto:doug.clow@xxxxxxxxxxx]
> Verzonden: vrijdag 3 mei 2013 8:17
> Aan: Maurits van de Lande
> CC: 'stgt@xxxxxxxxxxxxxxx'
> Onderwerp: Re: how to set VPD page 83 (Device Identification) using pacemaker
>
> Hi Maurits,
>
> I just asked the exact same question. I have the same setup and am looking to use this for Microsoft Failover Clustering. I haven't gotten any responses or seen any other emails on the mailing list thought, I'm wondering if this list is no longer used.
>
> Regards,
> Doug
>
>
>
> On May 2, 2013, at 5:27 AM, Maurits van de Lande <M.vandeLande@xxxxxxxxxxxxxxxx> wrote:
>
>> Hello,
>>
>> I have setup an iSCSI target using Centos6 and tgt. I would like to use this target with Microsoft Failover Clustering. Therefore I need to set the VPD page 83 (Device Identification).
>>
>> How can I set this parameter using iscsiadm?
>> And how can I set this parameter with pacemaker?
>>
>> Thanks,
>>
>> Maurits van de Lande
>>
>>
>>
>> --
>> To unsubscribe from this list: send the line "unsubscribe stgt" in the
>> body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at
>> http://vger.kernel.org/majordomo-info.html
>
>
>
--
To unsubscribe from this list: send the line "unsubscribe stgt" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
