Re: [PATCH] clocking-wizard: fix a schedule during spin lock acquisition

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Sun, Sep 18, 2022 at 02:43:20AM +0000, flyingpeng(彭浩) wrote:
> when the interrupt is disabled and the spin lock is acquired,
> calling read_poll_timeout will trigger the schedule, which should
> be replaced by read_poll_timeout_atomic.
> 
> Signed-off-by: Peng Hao <flyingpeng@xxxxxxxxxxx>
> ---
>  drivers/staging/clocking-wizard/clk-xlnx-clock-wizard.c | 4 ++--
>  1 file changed, 2 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/staging/clocking-wizard/clk-xlnx-clock-wizard.c b/drivers/staging/clocking-wizard/clk-xlnx-clock-wizard.c
> index 39367712ef54..986af03b31c9 100644
> --- a/drivers/staging/clocking-wizard/clk-xlnx-clock-wizard.c
> +++ b/drivers/staging/clocking-wizard/clk-xlnx-clock-wizard.c
> @@ -157,7 +157,7 @@ static int clk_wzrd_dynamic_reconfig(struct clk_hw *hw, unsigned long rate,
>         writel(0x00, div_addr + WZRD_DR_DIV_TO_PHASE_OFFSET);
> 
>         /* Check status register */
> -       err = readl_poll_timeout(divider->base + WZRD_DR_STATUS_REG_OFFSET,
> +       err = readl_poll_timeout_atomic(divider->base + WZRD_DR_STATUS_REG_OFFSET,
>                                  value, value & WZRD_DR_LOCK_BIT_MASK,
>                                  WZRD_USEC_POLL, WZRD_TIMEOUT_POLL);
>         if (err)
> @@ -168,7 +168,7 @@ static int clk_wzrd_dynamic_reconfig(struct clk_hw *hw, unsigned long rate,
>                divider->base + WZRD_DR_INIT_REG_OFFSET);
> 
>         /* Check status register */
> -       err = readl_poll_timeout(divider->base + WZRD_DR_STATUS_REG_OFFSET,
> +       err = readl_poll_timeout_atomic(divider->base + WZRD_DR_STATUS_REG_OFFSET,
>                                  value, value & WZRD_DR_LOCK_BIT_MASK,
>                                  WZRD_USEC_POLL, WZRD_TIMEOUT_POLL);
>  err_reconfig:
> --
> 2.27.0
> 

Hi,

This is the friendly patch-bot of Greg Kroah-Hartman.  You have sent him
a patch that has triggered this response.  He used to manually respond
to these common problems, but in order to save his sanity (he kept
writing the same thing over and over, yet to different people), I was
created.  Hopefully you will not take offence and will fix the problem
in your patch and resubmit it so that it can be accepted into the Linux
kernel tree.

You are receiving this message because of the following common error(s)
as indicated below:

- Your patch is malformed (tabs converted to spaces, linewrapped, etc.)
  and can not be applied.  Please read the file,
  Documentation/email-clients.txt in order to fix this.

If you wish to discuss this problem further, or you have questions about
how to resolve this issue, please feel free to respond to this email and
Greg will reply once he has dug out from the pending patches received
from other developers.

thanks,

greg k-h's patch email bot




[Index of Archives]     [Linux Driver Development]     [Linux Driver Backports]     [DMA Engine]     [Linux GPIO]     [Linux SPI]     [Video for Linux]     [Linux USB Devel]     [Linux Coverity]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Yosemite Backpacking]
  Powered by Linux