Re: [PATCH] staging: r8188eu: txpktbuf_bndy does not depend on wifi_spec

[Philipp Hortmann <philipp.g.hortmann@xxxxxxxxx>]

On 8/6/22 21:43, Martin Kaiser wrote:
> Remove the if clause that sets txpktbuf_bndy. Both branches set the same
> value.
>
> Signed-off-by: Martin Kaiser <martin@xxxxxxxxx>
> ---
>   drivers/staging/r8188eu/hal/usb_halinit.c      | 12 ++----------
>   drivers/staging/r8188eu/include/rtl8188e_hal.h |  6 ------
>   2 files changed, 2 insertions(+), 16 deletions(-)
>
> diff --git a/drivers/staging/r8188eu/hal/usb_halinit.c b/drivers/staging/r8188eu/hal/usb_halinit.c
> index efb529bb4c8a..8b36fb56076e 100644
> --- a/drivers/staging/r8188eu/hal/usb_halinit.c
> +++ b/drivers/staging/r8188eu/hal/usb_halinit.c
> @@ -567,7 +567,6 @@ u32 rtl8188eu_hal_init(struct adapter *Adapter)
>   {
>   	u8 value8 = 0;
>   	u16  value16;
> -	u8 txpktbuf_bndy;
>   	u32 status = _SUCCESS;
>   	int res;
>   	struct hal_data_8188e *haldata = &Adapter->haldata;
> @@ -600,13 +599,6 @@ u32 rtl8188eu_hal_init(struct adapter *Adapter)
>   	/*  HW GPIO pin. Before PHY_RFConfig8192C. */
>   	/*  2010/08/26 MH If Efuse does not support sective suspend then disable the function. */
>   
> -	if (!pregistrypriv->wifi_spec) {
> -		txpktbuf_bndy = TX_PAGE_BOUNDARY_88E;
> -	} else {
> -		/*  for WMM */
> -		txpktbuf_bndy = WMM_NORMAL_TX_PAGE_BOUNDARY_88E;
> -	}
> -
>   	_InitQueueReservedPage(Adapter);
>   	_InitQueuePriority(Adapter);
>   	_InitPageBoundary(Adapter);
> @@ -647,9 +639,9 @@ u32 rtl8188eu_hal_init(struct adapter *Adapter)
>   	if (status == _FAIL)
>   		goto exit;
>   
> -	_InitTxBufferBoundary(Adapter, txpktbuf_bndy);
> +	_InitTxBufferBoundary(Adapter, TX_PAGE_BOUNDARY_88E);
>   
> -	status =  InitLLTTable(Adapter, txpktbuf_bndy);
> +	status =  InitLLTTable(Adapter, TX_PAGE_BOUNDARY_88E);
>   	if (status == _FAIL)
>   		goto exit;
>   
> diff --git a/drivers/staging/r8188eu/include/rtl8188e_hal.h b/drivers/staging/r8188eu/include/rtl8188e_hal.h
> index 5cd62b216720..fdc187f4deaa 100644
> --- a/drivers/staging/r8188eu/include/rtl8188e_hal.h
> +++ b/drivers/staging/r8188eu/include/rtl8188e_hal.h
> @@ -51,12 +51,6 @@
>   
>   #define TX_PAGE_BOUNDARY_88E (TX_TOTAL_PAGE_NUMBER_88E + 1)
>   
> -/* Note: For Normal Chip Setting ,modify later */
> -#define WMM_NORMAL_TX_TOTAL_PAGE_NUMBER			\
> -	TX_TOTAL_PAGE_NUMBER_88E  /* 0xA9 , 0xb0=>176=>22k */
> -#define WMM_NORMAL_TX_PAGE_BOUNDARY_88E			\
> -	(WMM_NORMAL_TX_TOTAL_PAGE_NUMBER + 1) /* 0xA9 */
> -
>   #include "HalVerDef.h"
>   #include "hal_com.h"
>   

Tested-by: Philipp Hortmann <philipp.g.hortmann@xxxxxxxxx> # Edimax N150