[PATCH v3 4/6] staging: media: wave5: Add TODO file

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Add a TODO file listing all that is need for destaging.

Signed-off-by: Robert Beckett <bob.beckett@xxxxxxxxxxxxx>
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@xxxxxxxxxxxxx>
---
 drivers/staging/media/wave5/TODO | 59 ++++++++++++++++++++++++++++++++
 1 file changed, 59 insertions(+)
 create mode 100644 drivers/staging/media/wave5/TODO

diff --git a/drivers/staging/media/wave5/TODO b/drivers/staging/media/wave5/TODO
new file mode 100644
index 000000000000..98dc3b923ad6
--- /dev/null
+++ b/drivers/staging/media/wave5/TODO
@@ -0,0 +1,59 @@
+* Test on real silicon once available
+
+  This driver has so far been tested on pre-silicon FPGA and on the beta BeagleV
+  board which uses the StarFive JH7100 beta SoC.
+
+  Testing on FPGA shows it working fine, though the FPGA uses polled interrupts
+  and copied buffers between the host and it's on board RAM.
+
+  Testing on BeagleV shows buffer corruption that is currently attributed to a
+  known silicon issue in the SoC that makes the cache coherent interconnect not
+  so coherent.
+  This can likely be solved when the riscv non-coherent dma support lands and
+  provide optional v4l2 non-contiguous allocator, though it remains to be seen
+  whether support non-coherent use cases will be useful in real world hw.
+
+  Until we can test and resolve any issues on final silicon (due 2H 2021)
+  this driver should remain in staging.
+
+* Handle interrupts better
+
+  Currently the interrupt handling uses an unusual design employing a kfifo to
+  transfer irq status to irq thread. This was done as a work around for dropped
+  interrupts seen with IRQF_ONESHOT based handling.
+
+  This needs further investigation and fixing properly, with the aid of
+  C&M and StarFive engineers.
+
+* Fix early end of stream handling
+
+  When using a gstreamer pipeline like this:
+  gst-launch-1.0 filesrc location=<file> ! parsebin ! h264parse ! v4l2h264dec ! jpegenc ! identity eos-after=3 !  multifilesink location=%05d.jpeg
+  i.e. forced eos after 3 buffers
+  the pipeline stalls on exit waiting for end of job.
+  We need to add some form of early exit detection, instead of the current
+  behaviour of only considering a job finish on PIC_END.
+
+* Support more formats
+
+  The current frontend v4l2 layer only supports V4L2_PIX_FMT_HEVC and
+  V4L2_PIX_FMT_H264.
+  The backend logic supports other formats, so we should wire up the support
+  for further bitsream formats.
+
+* appropreate error handling:
+allocation failure, mutex acquire failure etc.
+
+* remove all unused struct fields
+
+* change struct fields to 'bool' type or bitfield when appropreate
+Likely good candidates are fields named '*_enable' , '*_on'
+
+* handle vdi_allocate_dma_memory failure , each function has to clean after itself
+
+* make sure that 'u32', 's32' etc. are only used when reading/writing hw
+and change s32 to u32 when s32 is not required
+
+* power management handling - add (runtime_)suspen/resume cb where the clock is enabled
+
+* fix checkpatch issues (mostly fixes , only left to fix MACRO_ARG_REUSE, LONG_LINE)
-- 
2.17.1





[Index of Archives]     [Linux Driver Development]     [Linux Driver Backports]     [DMA Engine]     [Linux GPIO]     [Linux SPI]     [Video for Linux]     [Linux USB Devel]     [Linux Coverity]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [Yosemite Backpacking]
  Powered by Linux