On Fri, May 14, 2021 at 04:05:32PM +0200, Greg KH wrote:
> On Fri, May 14, 2021 at 07:18:38PM +0530, Shreyansh Chouhan wrote:
> > On Fri, May 14, 2021 at 03:36:25PM +0200, Greg KH wrote:
> > > On Fri, May 14, 2021 at 07:00:39PM +0530, Shreyansh Chouhan wrote:
> > > > The gb_loopback_stats_attrs macro, (defined in loopback.c,) is a
> > > > multiline macro whose statements were not enclosed in a do while
> > > > loop.
> > > >
> > > > This patch adds a do while loop around the statements of the said
> > > > macro.
> > > >
> > > > Signed-off-by: Shreyansh Chouhan <chouhan.shreyansh630@xxxxxxxxx>
> > > > ---
> > > > drivers/staging/greybus/loopback.c | 10 ++++++----
> > > > 1 file changed, 6 insertions(+), 4 deletions(-)
> > > >
> > > > diff --git a/drivers/staging/greybus/loopback.c b/drivers/staging/greybus/loopback.c
> > > > index 2471448ba42a..c88ef3e894fa 100644
> > > > --- a/drivers/staging/greybus/loopback.c
> > > > +++ b/drivers/staging/greybus/loopback.c
> > > > @@ -162,10 +162,12 @@ static ssize_t name##_avg_show(struct device *dev, \
> > > > } \
> > > > static DEVICE_ATTR_RO(name##_avg)
> > > >
> > > > -#define gb_loopback_stats_attrs(field) \
> > > > - gb_loopback_ro_stats_attr(field, min, u); \
> > > > - gb_loopback_ro_stats_attr(field, max, u); \
> > > > - gb_loopback_ro_avg_attr(field)
> > > > +#define gb_loopback_stats_attrs(field) \
> > > > + do { \
> > > > + gb_loopback_ro_stats_attr(field, min, u); \
> > > > + gb_loopback_ro_stats_attr(field, max, u); \
> > > > + gb_loopback_ro_avg_attr(field); \
> > > > + } while (0)
> > > >
> > > > #define gb_loopback_attr(field, type) \
> > > > static ssize_t field##_show(struct device *dev, \
> > > > --
> > > > 2.31.1
> > > >
> > > >
> > >
> > > Did you test build this change?
> >
> > I built the module using make -C . M=drivers/staging/greybus to test
> > build it. I didn't get any errors.
>
> Really? Can you provide the full build output for this file with your
> change? I don't think you really built this file for the obvious
> reasons...
I ran make -C . M=drivers/staging/greybus
I got a three line output saying:
make: Entering directory '/work/linux'
MODPOST drivers/staging/greybus//Module.symvers
make: Leaving directory '/work/linux'
I just tried rebuilding the kernel with CONFIG_GREYBUS=m, and now I can
see what you are talking about. Why weren't these errors reported when I
ran the previous make command? Does that too check for the config
variables even when I specifically asked it to build a module?
Also sorry about this. I will be more careful next time.
>
> thanks,
>
> greg k-h
Regards,
Shreyansh Chouhan
