[PATCH v6 15/17] doc: iio: ad4695: add SPI offload support

[David Lechner <dlechner@xxxxxxxxxxxx>]

Document SPI offload support for the ad4695 driver.

Signed-off-by: David Lechner <dlechner@xxxxxxxxxxxx>
---

v6 changes:
* Fixed double "all"
* Don't abbreviate "sampling_frequency" attribute names for clarity.

v5 changes: new patch in v5
---
 Documentation/iio/ad4695.rst | 68 ++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 68 insertions(+)

diff --git a/Documentation/iio/ad4695.rst b/Documentation/iio/ad4695.rst
index 9ec8bf466c15bf94cbae2ebdb61875f66af1264f..ead0faadff4b5aede2a34bac52e103e375da6f21 100644
--- a/Documentation/iio/ad4695.rst
+++ b/Documentation/iio/ad4695.rst
@@ -47,6 +47,36 @@ In this mode, CNV and CS are tied together and there is a single SDO line.
 To use this mode, in the device tree, omit the ``cnv-gpios`` and
 ``spi-rx-bus-width`` properties.
 
+SPI offload wiring
+^^^^^^^^^^^^^^^^^^
+
+When used with a SPI offload, the supported wiring configuration is:
+
+.. code-block::
+
+    +-------------+         +-------------+
+    |    GP0/BUSY |-------->| TRIGGER     |
+    |          CS |<--------| CS          |
+    |             |         |             |
+    |     ADC     |         |     SPI     |
+    |             |         |             |
+    |         SDI |<--------| SDO         |
+    |         SDO |-------->| SDI         |
+    |        SCLK |<--------| SCLK        |
+    |             |         |             |
+    |             |         +-------------+
+    |         CNV |<-----+--| PWM         |
+    |             |      +--| GPIO        |
+    +-------------+         +-------------+
+
+In this case, both the ``cnv-gpios`` and  ``pwms`` properties are required.
+The ``#trigger-source-cells = <2>`` property is also required to connect back
+to the SPI offload. The SPI offload will have ``trigger-sources`` property
+with cells to indicate the busy signal and which GPx pin is used, e.g
+``<&ad4695 AD4695_TRIGGER_EVENT_BUSY AD4695_TRIGGER_PIN_GP0>``.
+
+.. seealso:: `SPI offload support`_
+
 Channel configuration
 ---------------------
 
@@ -158,6 +188,27 @@ Unimplemented features
 - GPIO support
 - CRC support
 
+SPI offload support
+===================
+
+To be able to achieve the maximum sample rate, the driver can be used with the
+`AXI SPI Engine`_ to provide SPI offload support.
+
+.. _AXI SPI Engine: http://analogdevicesinc.github.io/hdl/projects/ad469x_fmc/index.html
+
+.. seealso:: `SPI offload wiring`_
+
+When SPI offload is being used, some attributes will be different.
+
+* ``trigger`` directory is removed.
+* ``in_voltage0_sampling_frequency`` attributes are added for setting the sample
+  rate.
+* ``in_voltage0_sampling_frequency_available`` attributes are added for querying
+  the max sample rate.
+* ``timestamp`` channel is removed.
+* Buffer data format may be different compared to when offload is not used,
+  e.g. the ``buffer0/in_voltage0_type`` attribute.
+
 Device buffers
 ==============
 
@@ -165,3 +216,20 @@ This driver supports hardware triggered buffers. This uses the "advanced
 sequencer" feature of the chip to trigger a burst of conversions.
 
 Also see :doc:`iio_devbuf` for more general information.
+
+Effective sample rate for buffered reads
+----------------------------------------
+
+When SPI offload is not used, the sample rate is determined by the trigger that
+is manually configured in userspace. All enabled channels will be read in a
+burst when the trigger is received.
+
+When SPI offload is used, the sample rate is configured per channel. All
+channels will have the same rate, so only one ``in_voltageY_sampling_frequency``
+attribute needs to be set. Since this rate determines the delay between each
+individual conversion, the effective sample rate for each sample is actually
+the sum of the periods of each enabled channel in a buffered read. In other
+words, it is the value of the ``in_voltageY_sampling_frequency`` attribute
+divided by the number of enabled channels. So if 4 channels are enabled, with
+the ``in_voltageY_sampling_frequency`` attributes set to 1 MHz, the effective
+sample rate is 250 kHz.

-- 
2.43.0