Re: [PATCH v1 1/7] dt-bindings: i2c: qcom,i2c-geni: Document DT properties for QUP firmware loading

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, Dec 04, 2024 at 08:33:20PM +0530, Viken Dadhaniya wrote:
> Document the 'qcom,load-firmware' and 'qcom,xfer-mode' properties to
> support SE(Serial Engine) firmware loading from the protocol driver and to
> select the data transfer mode, either GPI DMA (Generic Packet Interface)
> or non-GPI mode (PIO/CPU DMA).
> 
> I2C controller can operate in one of two modes based on the
> 'qcom,xfer-mode' property, and the firmware is loaded accordingly.
> 
> Co-developed-by: Mukesh Kumar Savaliya <quic_msavaliy@xxxxxxxxxxx>
> Signed-off-by: Mukesh Kumar Savaliya <quic_msavaliy@xxxxxxxxxxx>
> Signed-off-by: Viken Dadhaniya <quic_vdadhani@xxxxxxxxxxx>
> ---
>  .../devicetree/bindings/i2c/qcom,i2c-geni-qcom.yaml   | 11 +++++++++++
>  1 file changed, 11 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/i2c/qcom,i2c-geni-qcom.yaml b/Documentation/devicetree/bindings/i2c/qcom,i2c-geni-qcom.yaml
> index 9f66a3bb1f80..a26f34fce1bb 100644
> --- a/Documentation/devicetree/bindings/i2c/qcom,i2c-geni-qcom.yaml
> +++ b/Documentation/devicetree/bindings/i2c/qcom,i2c-geni-qcom.yaml
> @@ -66,6 +66,15 @@ properties:
>    required-opps:
>      maxItems: 1
>  
> +  qcom,load-firmware:
> +    type: boolean
> +    description: Optional property to load SE (serial engine) Firmware from protocol driver.
> +
> +  qcom,xfer-mode:
> +    description: Value 1,2 and 3 represents FIFO, CPU DMA and GSI DMA mode respectively.
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    enum: [1, 2, 3]
> +
>  required:
>    - compatible
>    - interrupts
> @@ -142,5 +151,7 @@ examples:
>          interconnect-names = "qup-core", "qup-config", "qup-memory";
>          power-domains = <&rpmhpd SC7180_CX>;
>          required-opps = <&rpmhpd_opp_low_svs>;
> +        qcom,load-firmware;

please use instead:
firmware-name = "qcom/sc7180/qupv3.elf"

> +        qcom,xfer-mode = <1>;
>      };
>  ...
> -- 
> 2.34.1
> 

-- 
With best wishes
Dmitry




[Index of Archives]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux