[PATCH 15/24] spi: zynq-qspi: Support per spi-mem operation frequency switches

[Miquel Raynal <miquel.raynal@xxxxxxxxxxx>]

Every ->exec_op() call correctly configures the spi bus speed to the
maximum allowed frequency for the memory using the constant spi default
parameter. Since we can now have per-operation constraints, let's use
the value that comes from the spi-mem operation structure instead. In
case there is no specific limitation for this operation, the default spi
device value will be given anyway.

The per-operation frequency capability is thus advertised to the spi-mem
core.

Cc: Heiko Stuebner <heiko@xxxxxxxxx>
Signed-off-by: Miquel Raynal <miquel.raynal@xxxxxxxxxxx>
---
 drivers/spi/spi-zynq-qspi.c | 13 ++++++++++---
 1 file changed, 10 insertions(+), 3 deletions(-)

diff --git a/drivers/spi/spi-zynq-qspi.c b/drivers/spi/spi-zynq-qspi.c
index d6325c6be3d4..ee9555b46d06 100644
--- a/drivers/spi/spi-zynq-qspi.c
+++ b/drivers/spi/spi-zynq-qspi.c
@@ -318,6 +318,7 @@ static void zynq_qspi_chipselect(struct spi_device *spi, bool assert)
  * zynq_qspi_config_op - Configure QSPI controller for specified transfer
  * @xqspi:	Pointer to the zynq_qspi structure
  * @spi:	Pointer to the spi_device structure
+ * @op:		The memory operation to execute
  *
  * Sets the operational mode of QSPI controller for the next QSPI transfer and
  * sets the requested clock frequency.
@@ -331,7 +332,8 @@ static void zynq_qspi_chipselect(struct spi_device *spi, bool assert)
  * controller the driver will set the highest or lowest frequency supported by
  * controller.
  */
-static int zynq_qspi_config_op(struct zynq_qspi *xqspi, struct spi_device *spi)
+static int zynq_qspi_config_op(struct zynq_qspi *xqspi, struct spi_device *spi,
+			       const struct spi_mem_op *op)
 {
 	u32 config_reg, baud_rate_val = 0;
 
@@ -346,7 +348,7 @@ static int zynq_qspi_config_op(struct zynq_qspi *xqspi, struct spi_device *spi)
 	 */
 	while ((baud_rate_val < ZYNQ_QSPI_CONFIG_BAUD_DIV_MAX)  &&
 	       (clk_get_rate(xqspi->refclk) / (2 << baud_rate_val)) >
-		spi->max_speed_hz)
+		op->max_freq)
 		baud_rate_val++;
 
 	config_reg = zynq_qspi_read(xqspi, ZYNQ_QSPI_CONFIG_OFFSET);
@@ -534,7 +536,7 @@ static int zynq_qspi_exec_mem_op(struct spi_mem *mem,
 		op->dummy.buswidth, op->data.buswidth);
 
 	zynq_qspi_chipselect(mem->spi, true);
-	zynq_qspi_config_op(xqspi, mem->spi);
+	zynq_qspi_config_op(xqspi, mem->spi, op);
 
 	if (op->cmd.opcode) {
 		reinit_completion(&xqspi->data_completion);
@@ -620,6 +622,10 @@ static const struct spi_controller_mem_ops zynq_qspi_mem_ops = {
 	.exec_op = zynq_qspi_exec_mem_op,
 };
 
+static const struct spi_controller_mem_caps zynq_qspi_mem_caps = {
+	.per_op_freq = true,
+};
+
 /**
  * zynq_qspi_probe - Probe method for the QSPI driver
  * @pdev:	Pointer to the platform_device structure
@@ -706,6 +712,7 @@ static int zynq_qspi_probe(struct platform_device *pdev)
 	ctlr->mode_bits =  SPI_RX_DUAL | SPI_RX_QUAD |
 			    SPI_TX_DUAL | SPI_TX_QUAD;
 	ctlr->mem_ops = &zynq_qspi_mem_ops;
+	ctlr->mem_caps = &zynq_qspi_mem_caps;
 	ctlr->setup = zynq_qspi_setup_op;
 	ctlr->max_speed_hz = clk_get_rate(xqspi->refclk) / 2;
 	ctlr->dev.of_node = np;
-- 
2.43.0