[PATCH 0/4] Add bridged amplifiers to cs42l43

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On some cs42l43 systems a couple of cs35l56 amplifiers are attached
to the cs42l43's SPI and I2S. On Windows the cs42l43 is controlled
by a SDCA class driver and these two amplifiers are controlled by
firmware running on the cs42l43. However, under Linux the decision
was made to interact with the cs42l43 directly, affording the user
greater control over the audio system. However, this has resulted
in an issue where these two bridged cs35l56 amplifiers are not
populated in ACPI and must be added manually. There is at least an
SDCA extension unit DT entry we can key off.

The process of adding this is handled using a software node, firstly the
ability to add native chip selects to software nodes must be added.
Secondly, an additional flag for naming the SPI devices is added this
allows the machine driver to key to the correct amplifier. Then finally,
the cs42l43 SPI driver adds the two amplifiers directly onto its SPI
bus.

An additional series will follow soon to add the audio machine driver
parts (in the sof-sdw driver), however that is fairly orthogonal to
this part of the process, getting the actual amplifiers registered.

Thanks,
Charles

Series changes since v4:
 - Remove extraneous fwnode_handle_puts in driver/spi/spi-cs42l43.c
 - Make Kconfig for swnode undef gpios not user visible
 - Add some missing headers
 - Add patch to update handling in spi_dev_set_name
 - Remove stray blank line
 - Use ACPI_HANDLE_FWNODE

Series changes since v3:
 - Add Kconfig to make swnode conditionally built
 - Add define for swnode name
 - Add custom init and exit calls to register swnode
 - Use export namespaces
 - Always name swnode SPI devices after the node name
 - Correct some header includes
 - Use HZ_PER_MHZ
 - Use some swnode helper macros
 - Use acpi_get_local_address
 - Correct some handle puts
 - Add some dev_err_probes

Series changes since v2:
 - Add missing fwnode_handle_puts in driver/spi/spi-cs423l43.c

Series changes since v1:
 - Add missing statics in driver/spi/spi-cs42l43.c

Charles Keepax (2):
  gpio: swnode: Add ability to specify native chip selects for SPI
  spi: Add a mechanism to use the fwnode name for the SPI device

Maciej Strozek (1):
  spi: cs42l43: Add bridged cs35l56 amplifiers

Charles Keepax (3):
  gpio: swnode: Add ability to specify native chip selects for SPI
  spi: Switch to using is_acpi_device_node() in spi_dev_set_name()
  spi: Update swnode based SPI devices to use the fwnode name

Maciej Strozek (1):
  spi: cs42l43: Add bridged cs35l56 amplifiers

 drivers/gpio/Kconfig          |   3 +
 drivers/gpio/gpiolib-swnode.c |  40 ++++++++++
 drivers/spi/Kconfig           |   1 +
 drivers/spi/spi-cs42l43.c     | 135 +++++++++++++++++++++++++++++++++-
 drivers/spi/spi.c             |  13 +++-
 include/linux/gpio/consumer.h |   4 +
 6 files changed, 191 insertions(+), 5 deletions(-)

-- 
2.39.2





[Index of Archives]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux