Re: [PATCH v3 34/42] ARM: dts: add Cirrus EP93XX SoC .dtsi

[Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxx>]

On 20/07/2023 13:29, Nikita Shubin via B4 Relay wrote:
> From: Nikita Shubin <nikita.shubin@xxxxxxxxxxx>
> 
> Add support for Cirrus Logic EP93XX SoC's family.
> 
> Co-developed-by: Alexander Sverdlin <alexander.sverdlin@xxxxxxxxx>
> Signed-off-by: Alexander Sverdlin <alexander.sverdlin@xxxxxxxxx>
> Signed-off-by: Nikita Shubin <nikita.shubin@xxxxxxxxxxx>
> ---
>  arch/arm/boot/dts/cirrus/ep93xx.dtsi | 449 +++++++++++++++++++++++++++++++++++
>  1 file changed, 449 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/cirrus/ep93xx.dtsi b/arch/arm/boot/dts/cirrus/ep93xx.dtsi
> new file mode 100644
> index 000000000000..1e04f39d7b80
> --- /dev/null
> +++ b/arch/arm/boot/dts/cirrus/ep93xx.dtsi
> @@ -0,0 +1,449 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Device Tree file for Cirrus Logic systems EP93XX SoC
> + */
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/clock/cirrus,ep93xx-clock.h>
> +/ {
> +	soc: soc {
> +		compatible = "simple-bus";
> +		ranges;
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +
> +		syscon: syscon@80930000 {
> +			compatible = "cirrus,ep9301-syscon",
> +						 "syscon", "simple-mfd";

Fix alignment.

> +			reg = <0x80930000 0x1000>;
> +
> +			eclk: clock-controller {
> +				compatible = "cirrus,ep9301-clk";
> +				#clock-cells = <1>;
> +				clocks = <&xtali>;
> +				status = "okay";

Drop statuses when not needed.

> +			};
> +
> +			pinctrl: pinctrl {
> +				compatible = "cirrus,ep9301-pinctrl";
> +
> +				spi_default_pins: pins-spi {
> +					function = "spi";
> +					groups = "ssp";
> +				};
> +

...

> +
> +		keypad: keypad@800f0000 {
> +			compatible = "cirrus,ep9307-keypad";
> +			reg = <0x800f0000 0x0c>;
> +			interrupt-parent = <&vic0>;
> +			interrupts = <29>;
> +			clocks = <&eclk EP93XX_CLK_KEYPAD>;
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&keypad_default_pins>;
> +			linux,keymap =

No need for line break.

> +					<KEY_UP>,
> +					<KEY_DOWN>,
> +					<KEY_VOLUMEDOWN>,
> +					<KEY_HOME>,
> +					<KEY_RIGHT>,
> +					<KEY_LEFT>,
> +					<KEY_ENTER>,
> +					<KEY_VOLUMEUP>,
> +					<KEY_F6>,
> +					<KEY_F8>,
> +					<KEY_F9>,
> +					<KEY_F10>,
> +					<KEY_F1>,
> +					<KEY_F2>,
> +					<KEY_F3>,
> +					<KEY_POWER>;
> +		};
> +
> +		pwm0: pwm@80910000 {
> +			compatible = "cirrus,ep9301-pwm";
> +			reg = <0x80910000 0x10>;
> +			clocks = <&eclk EP93XX_CLK_PWM>;
> +			status = "disabled";
> +		};
> +
> +		pwm1: pwm@80910020 {
> +			compatible = "cirrus,ep9301-pwm";
> +			reg = <0x80910020 0x10>;
> +			clocks = <&eclk EP93XX_CLK_PWM>;
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&pwm1_default_pins>;
> +			status = "disabled";
> +		};
> +
> +		rtc0: rtc@80920000 {
> +			compatible = "cirrus,ep9301-rtc";
> +			reg = <0x80920000 0x100>;
> +		};
> +
> +		spi0: spi@808a0000 {
> +			compatible = "cirrus,ep9301-spi";
> +			reg = <0x808a0000 0x18>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			interrupt-parent = <&vic1>;
> +			interrupts = <21>;
> +			clocks = <&eclk EP93XX_CLK_SPI>;
> +			pinctrl-names = "default";
> +			pinctrl-0 = <&spi_default_pins>;
> +			status = "disabled";
> +		};
> +
> +		timer: timer@80810000 {
> +			compatible = "cirrus,ep9301-timer";
> +			reg = <0x80810000 0x100>;
> +			interrupt-parent = <&vic1>;
> +			interrupts = <19>;
> +		};
> +
> +		uart0: uart@808c0000 {
> +			compatible = "arm,primecell";

This looks incomplete.

> +			reg = <0x808c0000 0x1000>;
> +			arm,primecell-periphid = <0x00041010>;
> +			clocks = <&eclk EP93XX_CLK_UART1>, <&eclk EP93XX_CLK_UART>;
> +			clock-names = "apb:uart1", "apb_pclk";

It does not look like you tested the DTS against bindings. Please run
`make dtbs_check` (see
Documentation/devicetree/bindings/writing-schema.rst or
https://www.linaro.org/blog/tips-and-tricks-for-validating-devicetree-sources-with-the-devicetree-schema/
for instructions).

> +			interrupt-parent = <&vic1>;
> +			interrupts = <20>;
> +			status = "disabled";
> +		};
> +
> +		uart1: uart@808d0000 {
> +			compatible = "arm,primecell";
> +			reg = <0x808d0000 0x1000>;
> +			arm,primecell-periphid = <0x00041010>;
> +			clocks = <&eclk EP93XX_CLK_UART2>, <&eclk EP93XX_CLK_UART>;
> +			clock-names = "apb:uart2", "apb_pclk";

It does not look like you tested the DTS against bindings. Please run
`make dtbs_check` (see
Documentation/devicetree/bindings/writing-schema.rst or
https://www.linaro.org/blog/tips-and-tricks-for-validating-devicetree-sources-with-the-devicetree-schema/
for instructions).

> +			interrupt-parent = <&vic1>;
> +			interrupts = <22>;
> +			status = "disabled";
> +		};
> +
> +		uart2: uart@808b0000 {
> +			compatible = "arm,primecell";
> +			reg = <0x808b0000 0x1000>;
> +			arm,primecell-periphid = <0x00041010>;
> +			clocks = <&eclk EP93XX_CLK_UART3>, <&eclk EP93XX_CLK_UART>;
> +			clock-names = "apb:uart3", "apb_pclk";
> +			interrupt-parent = <&vic1>;
> +			interrupts = <23>;
> +			status = "disabled";
> +		};
> +
> +		usb0: usb@80020000 {
> +			compatible = "generic-ohci";
> +			reg = <0x80020000 0x10000>;
> +			interrupt-parent = <&vic1>;
> +			interrupts = <24>;
> +			clocks = <&eclk EP93XX_CLK_USB>;
> +			status = "disabled";
> +		};
> +
> +		watchdog0: watchdog@80940000 {
> +			compatible = "cirrus,ep9301-wdt";
> +			reg = <0x80940000 0x08>;
> +		};
> +	};
> +
> +	xtali: oscillator {
> +		compatible = "fixed-clock";
> +		#clock-cells = <0>;
> +		clock-frequency = <14745600>;
> +		clock-output-names = "xtali";
> +	};
> +
> +	i2c0: i2c {
> +		compatible = "i2c-gpio";
> +		sda-gpios = <&gpio6 1 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
> +		scl-gpios = <&gpio6 0 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;

Are you sure this is part of SoC? It is rather unusual... I would say
this would be the first SoC, where GPIO pins must be an I2C.



Best regards,
Krzysztof