Re: [PATCH v2 3/5] spi: Add support for Renesas CSI

[andy.shevchenko@xxxxxxxxx]

Thu, Jun 22, 2023 at 12:33:39PM +0100, Fabrizio Castro kirjoitti:
> The RZ/V2M SoC comes with the Clocked Serial Interface (CSI)
> IP, which is a master/slave SPI controller.
> 
> This commit adds a driver to support CSI master mode.

Submitting Patches recommends to use imperative voice.

...

+ bits.h

> +#include <linux/clk.h>
> +#include <linux/count_zeros.h>
> +#include <linux/interrupt.h>
> +#include <linux/iopoll.h>
> +#include <linux/platform_device.h>
> +#include <linux/reset.h>
> +#include <linux/spi/spi.h>

...

> +#define CSI_CKS_MAX		0x3FFF

If it's limited by number of bits, i would explicitly use that information as
(BIT(14) - 1).

...

> +#define CSI_MAX_SPI_SCKO	8000000

Units?
Also, HZ_PER_MHZ?

...

> +static const unsigned char x_trg[] = {
> +	0, 1, 1, 2, 2, 2, 2, 3,
> +	3, 3, 3, 3, 3, 3, 3, 4,
> +	4, 4, 4, 4, 4, 4, 4, 4,
> +	4, 4, 4, 4, 4, 4, 4, 5
> +};
> +
> +static const unsigned char x_trg_words[] = {
> +	1,  2,  2,  4,  4,  4,  4,  8,
> +	8,  8,  8,  8,  8,  8,  8,  16,
> +	16, 16, 16, 16, 16, 16, 16, 16,
> +	16, 16, 16, 16, 16, 16, 16, 32
> +};

Why do you need tables? At the first glance these values can be easily
calculated from indexes.

...

> +	rzv2m_csi_reg_write_bit(csi, CSI_CNT, CSI_CNT_CSIRST, assert);
> +
> +	if (assert) {

	If (!assert)
		return 0;

> +		return readl_poll_timeout(csi->base + CSI_MODE, reg,
> +					  !(reg & CSI_MODE_CSOT), 0,
> +					  CSI_EN_DIS_TIMEOUT_US);
> +	}
> +
> +	return 0;

...

> +	rzv2m_csi_reg_write_bit(csi, CSI_MODE, CSI_MODE_CSIE, enable);
> +
> +	if (!enable && wait)

In the similar way.

> +		return readl_poll_timeout(csi->base + CSI_MODE, reg,
> +					  !(reg & CSI_MODE_CSOT), 0,
> +					  CSI_EN_DIS_TIMEOUT_US);
> +
> +	return 0;

...

> +		for (i = 0; i < csi->words_to_transfer; i++)
> +			writel(buf[i], csi->base + CSI_OFIFO);

writesl()?

...

> +		for (i = 0; i < csi->words_to_transfer; i++)
> +			buf[i] = (u16)readl(csi->base + CSI_IFIFO);

readsl()?

...

> +		for (i = 0; i < csi->words_to_transfer; i++)
> +			buf[i] = (u8)readl(csi->base + CSI_IFIFO);

readsl()?

...

Yes, in read cases you would need carefully handle the buffer data.
Or drop the idea if it looks too monsterous.

...

> +	ret = rzv2m_csi_wait_for_interrupt(csi, CSI_INT_TREND, CSI_CNT_TREND_E);

> +

Unneeded blank line.

> +	if (ret == -ETIMEDOUT)
> +		csi->errors |= TX_TIMEOUT_ERROR;

...

> +	struct rzv2m_csi_priv *csi = (struct rzv2m_csi_priv *)data;

From/to void * does not need an explicit casting in C.

...

> +	/* Setup clock polarity and phase timing */
> +	rzv2m_csi_reg_write_bit(csi, CSI_CLKSEL, CSI_CLKSEL_CKP,
> +				!(spi->mode & SPI_CPOL));
> +	rzv2m_csi_reg_write_bit(csi, CSI_CLKSEL, CSI_CLKSEL_DAP,
> +				!(spi->mode & SPI_CPHA));

Is it a must to do in a sequential writes?

...

> +	bool tx_completed = csi->txbuf ? false : true;
> +	bool rx_completed = csi->rxbuf ? false : true;

Ternaries are redundant in the above.

...

> +	controller->mode_bits = SPI_CPOL | SPI_CPHA | SPI_LSB_FIRST;

SPI_MODE_X_MASK

...

> +	controller->dev.of_node = pdev->dev.of_node;

device_set_node();

-- 
With Best Regards,
Andy Shevchenko