[PATCH] spi: dw: remove delay between write and read

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Delay between write and read in polling mode is not necessary in dw spi
driver. It was added assuming that dw spi controller need the delay to
send data from tx fifo to spi devices. But it is not needed because
following reasons:
1) dw spi datasheet claims transfer begins when first data word is
   present in the transmit FIFO and a slave is enabled. So at least we
   do not need the full fifo-size-transfer time delay.
2) in practice, due to spi devices implementation, spi full-duplex
   (write and read real data) is always split into two transfers.
Delay between spi transfers may be needed. But this can be introduced by
using a more formal helper function "spi_transfer_delay_exec", in which
the delay time is passed by users through spi_ioc_transfer.

Signed-off-by: Jack Chen <zenghuchen@xxxxxxxxxx>
---
 drivers/spi/spi-dw-core.c | 20 +++++++-------------
 1 file changed, 7 insertions(+), 13 deletions(-)

diff --git a/drivers/spi/spi-dw-core.c b/drivers/spi/spi-dw-core.c
index c3bfb6c84cab..7c10fb353567 100644
--- a/drivers/spi/spi-dw-core.c
+++ b/drivers/spi/spi-dw-core.c
@@ -379,9 +379,12 @@ static void dw_spi_irq_setup(struct dw_spi *dws)
 
 /*
  * The iterative procedure of the poll-based transfer is simple: write as much
- * as possible to the Tx FIFO, wait until the pending to receive data is ready
- * to be read, read it from the Rx FIFO and check whether the performed
- * procedure has been successful.
+ * as possible to the Tx FIFO, then read from the Rx FIFO and check whether the
+ * performed procedure has been successful.
+ *
+ * Delay is introduced in the end of each transfer before (optionally) changing
+ * the chipselect status, then starting the next transfer or completing the
+ * list of @spi_message.
  *
  * Note this method the same way as the IRQ-based transfer won't work well for
  * the SPI devices connected to the controller with native CS due to the
@@ -390,21 +393,12 @@ static void dw_spi_irq_setup(struct dw_spi *dws)
 static int dw_spi_poll_transfer(struct dw_spi *dws,
 				struct spi_transfer *transfer)
 {
-	struct spi_delay delay;
-	u16 nbits;
 	int ret;
 
-	delay.unit = SPI_DELAY_UNIT_SCK;
-	nbits = dws->n_bytes * BITS_PER_BYTE;
-
 	do {
 		dw_writer(dws);
-
-		delay.value = nbits * (dws->rx_len - dws->tx_len);
-		spi_delay_exec(&delay, transfer);
-
 		dw_reader(dws);
-
+		spi_transfer_delay_exec(transfer);
 		ret = dw_spi_check_status(dws, true);
 		if (ret)
 			return ret;
-- 
2.40.0.rc1.284.g88254d51c5-goog




[Index of Archives]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux