Enable yamllint to check the prefered commenting style of requiring a
space after a comment character '#'. Fix the cases in the tree which
have a warning with this enabled. Most cases just need a space after the
'#'. A couple of cases with comments which were not intended to be
comments are revealed. Those were in ti,sa2ul.yaml, ti,cal.yaml, and
brcm,bcmgenet.yaml.
Signed-off-by: Rob Herring <robh@xxxxxxxxxx>
---
Cc: Krzysztof Kozlowski <krzysztof.kozlowski+dt@xxxxxxxxxx>
Cc: Stephen Boyd <sboyd@xxxxxxxxxx>
Cc: Herbert Xu <herbert@xxxxxxxxxxxxxxxxxxx>
Cc: "David S. Miller" <davem@xxxxxxxxxxxxx>
Cc: Rob Clark <robdclark@xxxxxxxxx>
Cc: Abhinav Kumar <quic_abhinavk@xxxxxxxxxxx>
Cc: Dmitry Baryshkov <dmitry.baryshkov@xxxxxxxxxx>
Cc: Sean Paul <sean@xxxxxxxxxx>
Cc: Thomas Gleixner <tglx@xxxxxxxxxxxxx>
Cc: Marc Zyngier <maz@xxxxxxxxxx>
Cc: Mauro Carvalho Chehab <mchehab@xxxxxxxxxx>
Cc: Eric Dumazet <edumazet@xxxxxxxxxx>
Cc: Jakub Kicinski <kuba@xxxxxxxxxx>
Cc: Paolo Abeni <pabeni@xxxxxxxxxx>
Cc: Andrew Lunn <andrew@xxxxxxx>
Cc: Heiner Kallweit <hkallweit1@xxxxxxxxx>
Cc: Vinod Koul <vkoul@xxxxxxxxxx>
Cc: Kishon Vijay Abraham I <kishon@xxxxxxxxxx>
Cc: Mark Brown <broonie@xxxxxxxxxx>
Cc: Conor Dooley <conor.dooley@xxxxxxxxxxxxx>
Cc: linux-clk@xxxxxxxxxxxxxxx
Cc: linux-crypto@xxxxxxxxxxxxxxx
Cc: dri-devel@xxxxxxxxxxxxxxxxxxxxx
Cc: freedreno@xxxxxxxxxxxxxxxxxxxxx
Cc: linux-media@xxxxxxxxxxxxxxx
Cc: netdev@xxxxxxxxxxxxxxx
Cc: linux-arm-kernel@xxxxxxxxxxxxxxxxxxx
Cc: linux-phy@xxxxxxxxxxxxxxxxxxx
Cc: linux-gpio@xxxxxxxxxxxxxxx
Cc: alsa-devel@xxxxxxxxxxxxxxxx
Cc: linux-riscv@xxxxxxxxxxxxxxxxxxx
Cc: linux-spi@xxxxxxxxxxxxxxx
---
Documentation/devicetree/bindings/.yamllint | 2 +-
.../bindings/clock/qcom,a53pll.yaml | 4 ++--
.../devicetree/bindings/crypto/ti,sa2ul.yaml | 4 ++--
.../bindings/display/msm/qcom,mdp5.yaml | 2 +-
.../interrupt-controller/arm,gic.yaml | 4 ++--
.../loongson,pch-msi.yaml | 2 +-
.../bindings/media/renesas,vin.yaml | 4 ++--
.../devicetree/bindings/media/ti,cal.yaml | 4 ++--
.../bindings/net/brcm,bcmgenet.yaml | 2 --
.../bindings/net/cortina,gemini-ethernet.yaml | 6 ++---
.../devicetree/bindings/net/mdio-gpio.yaml | 4 ++--
.../phy/marvell,armada-cp110-utmi-phy.yaml | 2 +-
.../bindings/phy/phy-stm32-usbphyc.yaml | 2 +-
.../phy/qcom,sc7180-qmp-usb3-dp-phy.yaml | 2 +-
.../bindings/pinctrl/pinctrl-mt8192.yaml | 2 +-
.../regulator/nxp,pca9450-regulator.yaml | 8 +++----
.../regulator/rohm,bd71828-regulator.yaml | 20 ++++++++--------
.../regulator/rohm,bd71837-regulator.yaml | 6 ++---
.../regulator/rohm,bd71847-regulator.yaml | 6 ++---
.../bindings/soc/renesas/renesas.yaml | 2 +-
.../devicetree/bindings/soc/ti/ti,pruss.yaml | 2 +-
.../bindings/sound/amlogic,axg-tdm-iface.yaml | 2 +-
.../bindings/sound/qcom,lpass-rx-macro.yaml | 4 ++--
.../bindings/sound/qcom,lpass-tx-macro.yaml | 4 ++--
.../bindings/sound/qcom,lpass-va-macro.yaml | 4 ++--
.../sound/qcom,q6dsp-lpass-ports.yaml | 2 +-
.../bindings/sound/simple-card.yaml | 24 +++++++++----------
.../bindings/spi/microchip,mpfs-spi.yaml | 2 +-
28 files changed, 65 insertions(+), 67 deletions(-)
diff --git a/Documentation/devicetree/bindings/.yamllint b/Documentation/devicetree/bindings/.yamllint
index 214abd3ec440..4abe9f0a1d46 100644
--- a/Documentation/devicetree/bindings/.yamllint
+++ b/Documentation/devicetree/bindings/.yamllint
@@ -19,7 +19,7 @@ rules:
colons: {max-spaces-before: 0, max-spaces-after: 1}
commas: {min-spaces-after: 1, max-spaces-after: 1}
comments:
- require-starting-space: false
+ require-starting-space: true
min-spaces-from-content: 1
comments-indentation: disable
document-start:
diff --git a/Documentation/devicetree/bindings/clock/qcom,a53pll.yaml b/Documentation/devicetree/bindings/clock/qcom,a53pll.yaml
index 525ebaa93c85..64bfd0f5d4d0 100644
--- a/Documentation/devicetree/bindings/clock/qcom,a53pll.yaml
+++ b/Documentation/devicetree/bindings/clock/qcom,a53pll.yaml
@@ -45,14 +45,14 @@ required:
additionalProperties: false
examples:
- #Example 1 - A53 PLL found on MSM8916 devices
+ # Example 1 - A53 PLL found on MSM8916 devices
- |
a53pll: clock@b016000 {
compatible = "qcom,msm8916-a53pll";
reg = <0xb016000 0x40>;
#clock-cells = <0>;
};
- #Example 2 - A53 PLL found on IPQ6018 devices
+ # Example 2 - A53 PLL found on IPQ6018 devices
- |
a53pll_ipq: clock-controller@b116000 {
compatible = "qcom,ipq6018-a53pll";
diff --git a/Documentation/devicetree/bindings/crypto/ti,sa2ul.yaml b/Documentation/devicetree/bindings/crypto/ti,sa2ul.yaml
index 0c15fefb6671..77ec8bc70bf7 100644
--- a/Documentation/devicetree/bindings/crypto/ti,sa2ul.yaml
+++ b/Documentation/devicetree/bindings/crypto/ti,sa2ul.yaml
@@ -26,8 +26,8 @@ properties:
dmas:
items:
- description: TX DMA Channel
- - description: RX DMA Channel #1
- - description: RX DMA Channel #2
+ - description: 'RX DMA Channel #1'
+ - description: 'RX DMA Channel #2'
dma-names:
items:
diff --git a/Documentation/devicetree/bindings/display/msm/qcom,mdp5.yaml b/Documentation/devicetree/bindings/display/msm/qcom,mdp5.yaml
index ef461ad6ce4a..a763cf8da122 100644
--- a/Documentation/devicetree/bindings/display/msm/qcom,mdp5.yaml
+++ b/Documentation/devicetree/bindings/display/msm/qcom,mdp5.yaml
@@ -61,7 +61,7 @@ properties:
- const: lut
- const: tbu
- const: tbu_rt
- #MSM8996 has additional iommu clock
+ # MSM8996 has additional iommu clock
- items:
- const: iface
- const: bus
diff --git a/Documentation/devicetree/bindings/interrupt-controller/arm,gic.yaml b/Documentation/devicetree/bindings/interrupt-controller/arm,gic.yaml
index 220256907461..a2846e493497 100644
--- a/Documentation/devicetree/bindings/interrupt-controller/arm,gic.yaml
+++ b/Documentation/devicetree/bindings/interrupt-controller/arm,gic.yaml
@@ -133,8 +133,8 @@ properties:
- items: # for "arm,cortex-a9-gic"
- const: PERIPHCLK
- const: PERIPHCLKEN
- - const: clk # for "arm,gic-400" and "nvidia,tegra210"
- - const: gclk #for "arm,pl390"
+ - const: clk # for "arm,gic-400" and "nvidia,tegra210"
+ - const: gclk # for "arm,pl390"
power-domains:
maxItems: 1
diff --git a/Documentation/devicetree/bindings/interrupt-controller/loongson,pch-msi.yaml b/Documentation/devicetree/bindings/interrupt-controller/loongson,pch-msi.yaml
index 1f6fd73d4624..31e6bfbc3fd3 100644
--- a/Documentation/devicetree/bindings/interrupt-controller/loongson,pch-msi.yaml
+++ b/Documentation/devicetree/bindings/interrupt-controller/loongson,pch-msi.yaml
@@ -46,7 +46,7 @@ required:
- loongson,msi-base-vec
- loongson,msi-num-vecs
-additionalProperties: true #fixme
+additionalProperties: true # fixme
examples:
- |
diff --git a/Documentation/devicetree/bindings/media/renesas,vin.yaml b/Documentation/devicetree/bindings/media/renesas,vin.yaml
index c0442e79cbb4..ffa7a6c4f212 100644
--- a/Documentation/devicetree/bindings/media/renesas,vin.yaml
+++ b/Documentation/devicetree/bindings/media/renesas,vin.yaml
@@ -69,7 +69,7 @@ properties:
resets:
maxItems: 1
- #The per-board settings for Gen2 and RZ/G1 platforms:
+ # The per-board settings for Gen2 and RZ/G1 platforms:
port:
$ref: /schemas/graph.yaml#/$defs/port-base
unevaluatedProperties: false
@@ -108,7 +108,7 @@ properties:
data-active: true
- #The per-board settings for Gen3 and RZ/G2 platforms:
+ # The per-board settings for Gen3 and RZ/G2 platforms:
renesas,id:
description: VIN channel number
$ref: /schemas/types.yaml#/definitions/uint32
diff --git a/Documentation/devicetree/bindings/media/ti,cal.yaml b/Documentation/devicetree/bindings/media/ti,cal.yaml
index f8e4d260d10a..26b3fedef355 100644
--- a/Documentation/devicetree/bindings/media/ti,cal.yaml
+++ b/Documentation/devicetree/bindings/media/ti,cal.yaml
@@ -75,7 +75,7 @@ properties:
port@0:
$ref: /schemas/graph.yaml#/$defs/port-base
unevaluatedProperties: false
- description: CSI2 Port #0
+ description: 'CSI2 Port #0'
properties:
endpoint:
@@ -93,7 +93,7 @@ properties:
port@1:
$ref: /schemas/graph.yaml#/$defs/port-base
unevaluatedProperties: false
- description: CSI2 Port #1
+ description: 'CSI2 Port #1'
properties:
endpoint:
diff --git a/Documentation/devicetree/bindings/net/brcm,bcmgenet.yaml b/Documentation/devicetree/bindings/net/brcm,bcmgenet.yaml
index c99034f053e8..0e5e5db32faf 100644
--- a/Documentation/devicetree/bindings/net/brcm,bcmgenet.yaml
+++ b/Documentation/devicetree/bindings/net/brcm,bcmgenet.yaml
@@ -73,8 +73,6 @@ allOf:
unevaluatedProperties: false
examples:
- #include <dt-bindings/interrupt-controller/arm-gic.h>
-
- |
ethernet@f0b60000 {
phy-mode = "internal";
diff --git a/Documentation/devicetree/bindings/net/cortina,gemini-ethernet.yaml b/Documentation/devicetree/bindings/net/cortina,gemini-ethernet.yaml
index 253b5d1407ee..44fd23a5fa2b 100644
--- a/Documentation/devicetree/bindings/net/cortina,gemini-ethernet.yaml
+++ b/Documentation/devicetree/bindings/net/cortina,gemini-ethernet.yaml
@@ -31,9 +31,9 @@ properties:
ranges: true
-#The subnodes represents the two ethernet ports in this device.
-#They are not independent of each other since they share resources
-#in the parent node, and are thus children.
+# The subnodes represents the two ethernet ports in this device.
+# They are not independent of each other since they share resources
+# in the parent node, and are thus children.
patternProperties:
"^ethernet-port@[0-9]+$":
type: object
diff --git a/Documentation/devicetree/bindings/net/mdio-gpio.yaml b/Documentation/devicetree/bindings/net/mdio-gpio.yaml
index 1d83b8dcce2c..137657341802 100644
--- a/Documentation/devicetree/bindings/net/mdio-gpio.yaml
+++ b/Documentation/devicetree/bindings/net/mdio-gpio.yaml
@@ -33,8 +33,8 @@ properties:
- description: MDIO
- description: MDO
-#Note: Each gpio-mdio bus should have an alias correctly numbered in "aliases"
-#node.
+# Note: Each gpio-mdio bus should have an alias correctly numbered in "aliases"
+# node.
additionalProperties:
type: object
diff --git a/Documentation/devicetree/bindings/phy/marvell,armada-cp110-utmi-phy.yaml b/Documentation/devicetree/bindings/phy/marvell,armada-cp110-utmi-phy.yaml
index 30f3b5f32a95..43416c216190 100644
--- a/Documentation/devicetree/bindings/phy/marvell,armada-cp110-utmi-phy.yaml
+++ b/Documentation/devicetree/bindings/phy/marvell,armada-cp110-utmi-phy.yaml
@@ -41,7 +41,7 @@ properties:
Phandle to the system controller node
$ref: /schemas/types.yaml#/definitions/phandle
-#Required child nodes:
+# Required child nodes:
patternProperties:
"^usb-phy@[0|1]$":
diff --git a/Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.yaml b/Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.yaml
index 5b4c915cc9e5..24a3dbde223b 100644
--- a/Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.yaml
+++ b/Documentation/devicetree/bindings/phy/phy-stm32-usbphyc.yaml
@@ -55,7 +55,7 @@ properties:
description: number of clock cells for ck_usbo_48m consumer
const: 0
-#Required child nodes:
+# Required child nodes:
patternProperties:
"^usb-phy@[0|1]$":
diff --git a/Documentation/devicetree/bindings/phy/qcom,sc7180-qmp-usb3-dp-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,sc7180-qmp-usb3-dp-phy.yaml
index 2e19a434c669..0ef2c9b9d466 100644
--- a/Documentation/devicetree/bindings/phy/qcom,sc7180-qmp-usb3-dp-phy.yaml
+++ b/Documentation/devicetree/bindings/phy/qcom,sc7180-qmp-usb3-dp-phy.yaml
@@ -83,7 +83,7 @@ properties:
description:
Phandle to a regulator supply to any specific refclk pll block.
-#Required nodes:
+# Required nodes:
patternProperties:
"^usb3-phy@[0-9a-f]+$":
type: object
diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8192.yaml b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8192.yaml
index e0e943e5b874..a09ebbfec574 100644
--- a/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8192.yaml
+++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-mt8192.yaml
@@ -51,7 +51,7 @@ properties:
description: The interrupt outputs to sysirq.
maxItems: 1
-#PIN CONFIGURATION NODES
+# PIN CONFIGURATION NODES
patternProperties:
'-pins$':
type: object
diff --git a/Documentation/devicetree/bindings/regulator/nxp,pca9450-regulator.yaml b/Documentation/devicetree/bindings/regulator/nxp,pca9450-regulator.yaml
index 835b53302db8..6b53dc87694e 100644
--- a/Documentation/devicetree/bindings/regulator/nxp,pca9450-regulator.yaml
+++ b/Documentation/devicetree/bindings/regulator/nxp,pca9450-regulator.yaml
@@ -17,10 +17,10 @@ description: |
Datasheet is available at
https://www.nxp.com/docs/en/data-sheet/PCA9450DS.pdf
-#The valid names for PCA9450 regulator nodes are:
-#BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6,
-#LDO1, LDO2, LDO3, LDO4, LDO5
-#Note: Buck3 removed on PCA9450B and connect with Buck1 on PCA9450C.
+# The valid names for PCA9450 regulator nodes are:
+# BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6,
+# LDO1, LDO2, LDO3, LDO4, LDO5
+# Note: Buck3 removed on PCA9450B and connect with Buck1 on PCA9450C.
properties:
compatible:
diff --git a/Documentation/devicetree/bindings/regulator/rohm,bd71828-regulator.yaml b/Documentation/devicetree/bindings/regulator/rohm,bd71828-regulator.yaml
index 3cbe3b76ccee..bbf38d5cd06d 100644
--- a/Documentation/devicetree/bindings/regulator/rohm,bd71828-regulator.yaml
+++ b/Documentation/devicetree/bindings/regulator/rohm,bd71828-regulator.yaml
@@ -82,20 +82,20 @@ patternProperties:
# Supported default DVS states:
# buck | run | idle | suspend | lpsr
- #--------------------------------------------------------------
+ # --------------------------------------------------------------
# 1, 2, 6, and 7 | supported | supported | supported (*)
- #--------------------------------------------------------------
+ # --------------------------------------------------------------
# 3, 4, and 5 | supported (**)
- #--------------------------------------------------------------
+ # --------------------------------------------------------------
#
- #(*) LPSR and SUSPEND states use same voltage but both states have own
- # enable /
- # disable settings. Voltage 0 can be specified for a state to make
- # regulator disabled on that state.
+ # (*) LPSR and SUSPEND states use same voltage but both states have own
+ # enable /
+ # disable settings. Voltage 0 can be specified for a state to make
+ # regulator disabled on that state.
#
- #(**) All states use same voltage but have own enable / disable
- # settings. Voltage 0 can be specified for a state to make
- # regulator disabled on that state.
+ # (**) All states use same voltage but have own enable / disable
+ # settings. Voltage 0 can be specified for a state to make
+ # regulator disabled on that state.
required:
- regulator-name
diff --git a/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.yaml b/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.yaml
index ab842817d847..abf1fbdf3850 100644
--- a/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.yaml
+++ b/Documentation/devicetree/bindings/regulator/rohm,bd71837-regulator.yaml
@@ -23,9 +23,9 @@ description: |
if they are disabled at startup the voltage monitoring for LDO5/LDO6 will
cause PMIC to reset.
-#The valid names for BD71837 regulator nodes are:
-#BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6, BUCK7, BUCK8
-#LDO1, LDO2, LDO3, LDO4, LDO5, LDO6, LDO7
+# The valid names for BD71837 regulator nodes are:
+# BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6, BUCK7, BUCK8
+# LDO1, LDO2, LDO3, LDO4, LDO5, LDO6, LDO7
patternProperties:
"^LDO[1-7]$":
diff --git a/Documentation/devicetree/bindings/regulator/rohm,bd71847-regulator.yaml b/Documentation/devicetree/bindings/regulator/rohm,bd71847-regulator.yaml
index 65fc3d15f693..34ce781954b6 100644
--- a/Documentation/devicetree/bindings/regulator/rohm,bd71847-regulator.yaml
+++ b/Documentation/devicetree/bindings/regulator/rohm,bd71847-regulator.yaml
@@ -22,9 +22,9 @@ description: |
not be disabled by driver at startup. If BUCK5 is disabled at startup the
voltage monitoring for LDO5/LDO6 can cause PMIC to reset.
-#The valid names for BD71847 regulator nodes are:
-#BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6
-#LDO1, LDO2, LDO3, LDO4, LDO5, LDO6
+# The valid names for BD71847 regulator nodes are:
+# BUCK1, BUCK2, BUCK3, BUCK4, BUCK5, BUCK6
+# LDO1, LDO2, LDO3, LDO4, LDO5, LDO6
patternProperties:
"^LDO[1-6]$":
diff --git a/Documentation/devicetree/bindings/soc/renesas/renesas.yaml b/Documentation/devicetree/bindings/soc/renesas/renesas.yaml
index 2789022b52eb..3a618b4c8ab7 100644
--- a/Documentation/devicetree/bindings/soc/renesas/renesas.yaml
+++ b/Documentation/devicetree/bindings/soc/renesas/renesas.yaml
@@ -111,7 +111,7 @@ properties:
- description: RZ/G1C (R8A77470)
items:
- enum:
- - iwave,g23s #iWave Systems RZ/G1C Single Board Computer (iW-RainboW-G23S)
+ - iwave,g23s # iWave Systems RZ/G1C Single Board Computer (iW-RainboW-G23S)
- const: renesas,r8a77470
- description: RZ/G2M (R8A774A1)
diff --git a/Documentation/devicetree/bindings/soc/ti/ti,pruss.yaml b/Documentation/devicetree/bindings/soc/ti/ti,pruss.yaml
index 847873289f25..c697691f1fd4 100644
--- a/Documentation/devicetree/bindings/soc/ti/ti,pruss.yaml
+++ b/Documentation/devicetree/bindings/soc/ti/ti,pruss.yaml
@@ -313,7 +313,7 @@ additionalProperties: false
# Due to inability of correctly verifying sub-nodes with an @address through
# the "required" list, the required sub-nodes below are commented out for now.
-#required:
+# required:
# - memories
# - interrupt-controller
# - pru
diff --git a/Documentation/devicetree/bindings/sound/amlogic,axg-tdm-iface.yaml b/Documentation/devicetree/bindings/sound/amlogic,axg-tdm-iface.yaml
index 320f0002649d..45955d8a26d1 100644
--- a/Documentation/devicetree/bindings/sound/amlogic,axg-tdm-iface.yaml
+++ b/Documentation/devicetree/bindings/sound/amlogic,axg-tdm-iface.yaml
@@ -24,7 +24,7 @@ properties:
items:
- description: Bit clock
- description: Sample clock
- - description: Master clock #optional
+ - description: Master clock # optional
clock-names:
minItems: 2
diff --git a/Documentation/devicetree/bindings/sound/qcom,lpass-rx-macro.yaml b/Documentation/devicetree/bindings/sound/qcom,lpass-rx-macro.yaml
index 79c6f8da1319..e6fcf542cf87 100644
--- a/Documentation/devicetree/bindings/sound/qcom,lpass-rx-macro.yaml
+++ b/Documentation/devicetree/bindings/sound/qcom,lpass-rx-macro.yaml
@@ -34,13 +34,13 @@ properties:
clock-names:
oneOf:
- - items: #for ADSP based platforms
+ - items: # for ADSP based platforms
- const: mclk
- const: npl
- const: macro
- const: dcodec
- const: fsgen
- - items: #for ADSP bypass based platforms
+ - items: # for ADSP bypass based platforms
- const: mclk
- const: npl
- const: fsgen
diff --git a/Documentation/devicetree/bindings/sound/qcom,lpass-tx-macro.yaml b/Documentation/devicetree/bindings/sound/qcom,lpass-tx-macro.yaml
index da5f70910da5..6c8751497d36 100644
--- a/Documentation/devicetree/bindings/sound/qcom,lpass-tx-macro.yaml
+++ b/Documentation/devicetree/bindings/sound/qcom,lpass-tx-macro.yaml
@@ -36,13 +36,13 @@ properties:
clock-names:
oneOf:
- - items: #for ADSP based platforms
+ - items: # for ADSP based platforms
- const: mclk
- const: npl
- const: macro
- const: dcodec
- const: fsgen
- - items: #for ADSP bypass based platforms
+ - items: # for ADSP bypass based platforms
- const: mclk
- const: npl
- const: fsgen
diff --git a/Documentation/devicetree/bindings/sound/qcom,lpass-va-macro.yaml b/Documentation/devicetree/bindings/sound/qcom,lpass-va-macro.yaml
index 0a3c688ef1ec..61cdfc265b0f 100644
--- a/Documentation/devicetree/bindings/sound/qcom,lpass-va-macro.yaml
+++ b/Documentation/devicetree/bindings/sound/qcom,lpass-va-macro.yaml
@@ -34,11 +34,11 @@ properties:
clock-names:
oneOf:
- - items: #for ADSP based platforms
+ - items: # for ADSP based platforms
- const: mclk
- const: macro
- const: dcodec
- - items: #for ADSP bypass based platforms
+ - items: # for ADSP bypass based platforms
- const: mclk
clock-output-names:
diff --git a/Documentation/devicetree/bindings/sound/qcom,q6dsp-lpass-ports.yaml b/Documentation/devicetree/bindings/sound/qcom,q6dsp-lpass-ports.yaml
index d06f188030a3..044e77718a1b 100644
--- a/Documentation/devicetree/bindings/sound/qcom,q6dsp-lpass-ports.yaml
+++ b/Documentation/devicetree/bindings/sound/qcom,q6dsp-lpass-ports.yaml
@@ -26,7 +26,7 @@ properties:
'#size-cells':
const: 0
-#Digital Audio Interfaces
+# Digital Audio Interfaces
patternProperties:
'^dai@[0-9]+$':
type: object
diff --git a/Documentation/devicetree/bindings/sound/simple-card.yaml b/Documentation/devicetree/bindings/sound/simple-card.yaml
index f0d81bfe2598..806e2fff165f 100644
--- a/Documentation/devicetree/bindings/sound/simple-card.yaml
+++ b/Documentation/devicetree/bindings/sound/simple-card.yaml
@@ -262,9 +262,9 @@ required:
additionalProperties: false
examples:
-#--------------------
+# --------------------
# single DAI link
-#--------------------
+# --------------------
- |
sound {
compatible = "simple-audio-card";
@@ -291,9 +291,9 @@ examples:
};
};
-#--------------------
+# --------------------
# Multi DAI links
-#--------------------
+# --------------------
- |
sound {
compatible = "simple-audio-card";
@@ -334,10 +334,10 @@ examples:
};
};
-#--------------------
+# --------------------
# route audio from IMX6 SSI2 through TLV320DAC3100 codec
# through TPA6130A2 amplifier to headphones:
-#--------------------
+# --------------------
- |
sound {
compatible = "simple-audio-card";
@@ -359,9 +359,9 @@ examples:
};
};
-#--------------------
+# --------------------
# Sampling Rate Conversion
-#--------------------
+# --------------------
- |
sound {
compatible = "simple-audio-card";
@@ -387,9 +387,9 @@ examples:
};
};
-#--------------------
+# --------------------
# 2 CPU 1 Codec (Mixing)
-#--------------------
+# --------------------
- |
sound {
compatible = "simple-audio-card";
@@ -424,7 +424,7 @@ examples:
};
};
-#--------------------
+# --------------------
# Multi DAI links with DPCM:
#
# CPU0 ------ ak4613
@@ -433,7 +433,7 @@ examples:
# CPU3 --/ /* DPCM 5ch/6ch */
# CPU4 --/ /* DPCM 7ch/8ch */
# CPU5 ------ PCM3168A-c
-#--------------------
+# --------------------
- |
sound {
compatible = "simple-audio-card";
diff --git a/Documentation/devicetree/bindings/spi/microchip,mpfs-spi.yaml b/Documentation/devicetree/bindings/spi/microchip,mpfs-spi.yaml
index 1051690e3753..74a817cc7d94 100644
--- a/Documentation/devicetree/bindings/spi/microchip,mpfs-spi.yaml
+++ b/Documentation/devicetree/bindings/spi/microchip,mpfs-spi.yaml
@@ -22,7 +22,7 @@ properties:
- items:
- const: microchip,mpfs-qspi
- const: microchip,coreqspi-rtl-v2
- - const: microchip,coreqspi-rtl-v2 #FPGA QSPI
+ - const: microchip,coreqspi-rtl-v2 # FPGA QSPI
- const: microchip,mpfs-spi
reg:
--
2.39.2
[PATCH] dt-bindings: yamllint: Require a space after a comment '#'
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
- Subject: [PATCH] dt-bindings: yamllint: Require a space after a comment '#'
- From: Rob Herring <robh@xxxxxxxxxx>
- Date: Fri, 3 Mar 2023 15:42:23 -0600
- Cc: linux-kernel@xxxxxxxxxxxxxxx, Krzysztof Kozlowski <krzysztof.kozlowski+dt@xxxxxxxxxx>, Stephen Boyd <sboyd@xxxxxxxxxx>, Herbert Xu <herbert@xxxxxxxxxxxxxxxxxxx>, "David S. Miller" <davem@xxxxxxxxxxxxx>, Rob Clark <robdclark@xxxxxxxxx>, Abhinav Kumar <quic_abhinavk@xxxxxxxxxxx>, Dmitry Baryshkov <dmitry.baryshkov@xxxxxxxxxx>, Sean Paul <sean@xxxxxxxxxx>, Thomas Gleixner <tglx@xxxxxxxxxxxxx>, Marc Zyngier <maz@xxxxxxxxxx>, Mauro Carvalho Chehab <mchehab@xxxxxxxxxx>, Eric Dumazet <edumazet@xxxxxxxxxx>, Jakub Kicinski <kuba@xxxxxxxxxx>, Paolo Abeni <pabeni@xxxxxxxxxx>, Andrew Lunn <andrew@xxxxxxx>, Heiner Kallweit <hkallweit1@xxxxxxxxx>, Vinod Koul <vkoul@xxxxxxxxxx>, Kishon Vijay Abraham I <kishon@xxxxxxxxxx>, Mark Brown <broonie@xxxxxxxxxx>, Conor Dooley <conor.dooley@xxxxxxxxxxxxx>, linux-clk@xxxxxxxxxxxxxxx, linux-crypto@xxxxxxxxxxxxxxx, dri-devel@xxxxxxxxxxxxxxxxxxxxx, freedreno@xxxxxxxxxxxxxxxxxxxxx, linux-media@xxxxxxxxxxxxxxx, netdev@xxxxxxxxxxxxxxx, linux-arm-kernel@xxxxxxxxxxxxxxxxxxx, linux-phy@xxxxxxxxxxxxxxxxxxx, linux-gpio@xxxxxxxxxxxxxxx, alsa-devel@xxxxxxxxxxxxxxxx, linux-riscv@xxxxxxxxxxxxxxxxxxx, linux-spi@xxxxxxxxxxxxxxx
- Follow-Ups:
- Re: [PATCH] dt-bindings: yamllint: Require a space after a comment '#'
- From: Rob Herring
- Re: [PATCH] dt-bindings: yamllint: Require a space after a comment '#'
- From: Simon Horman
- Re: [PATCH] dt-bindings: yamllint: Require a space after a comment '#'
- From: Mark Brown
- Re: [PATCH] dt-bindings: yamllint: Require a space after a comment '#'
- From: Jakub Kicinski
- Re: [PATCH] dt-bindings: yamllint: Require a space after a comment '#'
- From: Dmitry Baryshkov
- Re: [PATCH] dt-bindings: yamllint: Require a space after a comment '#'
- From: Conor Dooley
- Re: [PATCH] dt-bindings: yamllint: Require a space after a comment '#'
- Prev by Date: Re: [PATCH] dt-bindings: yamllint: Require a space after a comment '#'
- Next by Date: Re: [PATCH 03/87] spi: aspeed-smc: Convert to platform remove callback returning void
- Previous by thread: [PATCH 00/87] spi: Convert to platform remove callback returning void
- Next by thread: Re: [PATCH] dt-bindings: yamllint: Require a space after a comment '#'
- Index(es):
 |