[Patch V7 1/3] spi: Add TPM HW flow flag

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



TPM specification [1] defines flow control over SPI. Client device can
insert a wait state on MISO when address is transmitted by controller
on MOSI. Detecting the wait state in software is only possible for
full duplex controllers. For controllers that support only half-
duplex, the wait state detection needs to be implemented in hardware.

Add a flag SPI_TPM_HW_FLOW for TPM device to set when software flow
control is not possible and hardware flow control is expected from
SPI controller.

Reference:
[1] https://trustedcomputinggroup.org/resource/pc-client-work-group-
pc-client-specific-tpm-interface-specification-tis/

Signed-off-by: Krishna Yarlagadda <kyarlagadda@xxxxxxxxxx>
---
 include/linux/spi/spi.h | 16 +++++++++++++---
 1 file changed, 13 insertions(+), 3 deletions(-)

diff --git a/include/linux/spi/spi.h b/include/linux/spi/spi.h
index 4fa26b9a3572..b9e49ed42955 100644
--- a/include/linux/spi/spi.h
+++ b/include/linux/spi/spi.h
@@ -184,8 +184,18 @@ struct spi_device {
 	u8			chip_select;
 	u8			bits_per_word;
 	bool			rt;
-#define SPI_NO_TX	BIT(31)		/* No transmit wire */
-#define SPI_NO_RX	BIT(30)		/* No receive wire */
+#define SPI_NO_TX		BIT(31)		/* No transmit wire */
+#define SPI_NO_RX		BIT(30)		/* No receive wire */
+	/*
+	 * TPM specification defines flow control over SPI. Client device
+	 * can insert a wait state on MISO when address is transmitted by
+	 * controller on MOSI. Detecting the wait state in software is only
+	 * possible for full duplex controllers. For controllers that support
+	 * only half-duplex, the wait state detection needs to be implemented
+	 * in hardware. TPM devices would set this flag when hardware flow
+	 * control is expected from SPI controller.
+	 */
+#define SPI_TPM_HW_FLOW		BIT(29)		/* TPM HW flow control */
 	/*
 	 * All bits defined above should be covered by SPI_MODE_KERNEL_MASK.
 	 * The SPI_MODE_KERNEL_MASK has the SPI_MODE_USER_MASK counterpart,
@@ -195,7 +205,7 @@ struct spi_device {
 	 * These bits must not overlap. A static assert check should make sure of that.
 	 * If adding extra bits, make sure to decrease the bit index below as well.
 	 */
-#define SPI_MODE_KERNEL_MASK	(~(BIT(30) - 1))
+#define SPI_MODE_KERNEL_MASK	(~(BIT(29) - 1))
 	u32			mode;
 	int			irq;
 	void			*controller_state;
-- 
2.17.1




[Index of Archives]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux