[Patch V3 1/3] tpm_tis-spi: Support hardware wait polling

[Krishna Yarlagadda <kyarlagadda@xxxxxxxxxx>]

TPM devices raise wait signal on last addr cycle. This can be detected
by software driver by reading MISO line on same clock which requires
full duplex support. In case of half duplex controllers wait detection
has to be implemented in HW.
Support hardware wait state detection by sending entire message and let
controller handle flow control.
QSPI controller in Tegra236 & Tegra241 implement TPM wait polling.

Signed-off-by: Krishna Yarlagadda <kyarlagadda@xxxxxxxxxx>
---
 drivers/char/tpm/tpm_tis_spi_main.c | 90 ++++++++++++++++++++++++++++-
 include/linux/spi/spi.h             |  7 ++-
 2 files changed, 92 insertions(+), 5 deletions(-)

diff --git a/drivers/char/tpm/tpm_tis_spi_main.c b/drivers/char/tpm/tpm_tis_spi_main.c
index a0963a3e92bd..0d3da7ef9a89 100644
--- a/drivers/char/tpm/tpm_tis_spi_main.c
+++ b/drivers/char/tpm/tpm_tis_spi_main.c
@@ -71,8 +71,72 @@ static int tpm_tis_spi_flow_control(struct tpm_tis_spi_phy *phy,
 	return 0;
 }
 
-int tpm_tis_spi_transfer(struct tpm_tis_data *data, u32 addr, u16 len,
-			 u8 *in, const u8 *out)
+int tpm_tis_spi_hw_flow_transfer(struct tpm_tis_data *data, u32 addr, u16 len,
+				 u8 *in, const u8 *out)
+{
+	struct tpm_tis_spi_phy *phy = to_tpm_tis_spi_phy(data);
+	struct spi_transfer spi_xfer[3];
+	struct spi_message m;
+	u8 transfer_len;
+	int ret;
+
+	spi_bus_lock(phy->spi_device->master);
+
+	while (len) {
+		transfer_len = min_t(u16, len, MAX_SPI_FRAMESIZE);
+
+		spi_message_init(&m);
+		phy->iobuf[0] = (in ? 0x80 : 0) | (transfer_len - 1);
+		phy->iobuf[1] = 0xd4;
+		phy->iobuf[2] = addr >> 8;
+		phy->iobuf[3] = addr;
+
+		memset(&spi_xfer, 0, sizeof(spi_xfer));
+
+		spi_xfer[0].tx_buf = phy->iobuf;
+		spi_xfer[0].len = 1;
+		spi_message_add_tail(&spi_xfer[0], &m);
+
+		spi_xfer[1].tx_buf = phy->iobuf + 1;
+		spi_xfer[1].len = 3;
+		spi_message_add_tail(&spi_xfer[1], &m);
+
+		if (out) {
+			spi_xfer[2].tx_buf = &phy->iobuf[4];
+			spi_xfer[2].rx_buf = NULL;
+			memcpy(&phy->iobuf[4], out, transfer_len);
+			out += transfer_len;
+		}
+
+		if (in) {
+			spi_xfer[2].tx_buf = NULL;
+			spi_xfer[2].rx_buf = &phy->iobuf[4];
+		}
+
+		spi_xfer[2].len = transfer_len;
+		spi_message_add_tail(&spi_xfer[2], &m);
+
+		reinit_completion(&phy->ready);
+
+		ret = spi_sync_locked(phy->spi_device, &m);
+		if (ret < 0)
+			goto exit;
+
+		if (in) {
+			memcpy(in, &phy->iobuf[4], transfer_len);
+			in += transfer_len;
+		}
+
+		len -= transfer_len;
+	}
+
+exit:
+	spi_bus_unlock(phy->spi_device->master);
+	return ret;
+}
+
+int tpm_tis_spi_sw_flow_transfer(struct tpm_tis_data *data, u32 addr, u16 len,
+				 u8 *in, const u8 *out)
 {
 	struct tpm_tis_spi_phy *phy = to_tpm_tis_spi_phy(data);
 	int ret = 0;
@@ -140,6 +204,28 @@ int tpm_tis_spi_transfer(struct tpm_tis_data *data, u32 addr, u16 len,
 	return ret;
 }
 
+int tpm_tis_spi_transfer(struct tpm_tis_data *data, u32 addr, u16 len,
+			 u8 *in, const u8 *out)
+{
+	struct tpm_tis_spi_phy *phy = to_tpm_tis_spi_phy(data);
+	struct spi_controller *ctlr = phy->spi_device->controller;
+
+	/*
+	 * TPM flow control over SPI requires full duplex support.
+	 * Send entire message to a half duplex controller to handle
+	 * wait polling in controller.
+	 * Set TPM HW flow control flag..
+	 */
+	if (ctlr->flags & SPI_CONTROLLER_HALF_DUPLEX) {
+		phy->spi_device->mode |= SPI_TPM_HW_FLOW;
+		return tpm_tis_spi_hw_flow_transfer(data, addr, len, in,
+						    out);
+	} else {
+		return tpm_tis_spi_sw_flow_transfer(data, addr, len, in,
+						    out);
+	}
+}
+
 static int tpm_tis_spi_read_bytes(struct tpm_tis_data *data, u32 addr,
 				  u16 len, u8 *result, enum tpm_tis_io_mode io_mode)
 {
diff --git a/include/linux/spi/spi.h b/include/linux/spi/spi.h
index 988aabc31871..b88494e31239 100644
--- a/include/linux/spi/spi.h
+++ b/include/linux/spi/spi.h
@@ -184,8 +184,9 @@ struct spi_device {
 	u8			chip_select;
 	u8			bits_per_word;
 	bool			rt;
-#define SPI_NO_TX	BIT(31)		/* No transmit wire */
-#define SPI_NO_RX	BIT(30)		/* No receive wire */
+#define SPI_NO_TX		BIT(31)		/* No transmit wire */
+#define SPI_NO_RX		BIT(30)		/* No receive wire */
+#define SPI_TPM_HW_FLOW		BIT(29)		/* TPM flow control */
 	/*
 	 * All bits defined above should be covered by SPI_MODE_KERNEL_MASK.
 	 * The SPI_MODE_KERNEL_MASK has the SPI_MODE_USER_MASK counterpart,
@@ -195,7 +196,7 @@ struct spi_device {
 	 * These bits must not overlap. A static assert check should make sure of that.
 	 * If adding extra bits, make sure to decrease the bit index below as well.
 	 */
-#define SPI_MODE_KERNEL_MASK	(~(BIT(30) - 1))
+#define SPI_MODE_KERNEL_MASK	(~(BIT(29) - 1))
 	u32			mode;
 	int			irq;
 	void			*controller_state;
-- 
2.17.1