[PATCH v3 10/15] spi: bcm63xx-hsspi: Fix multi-bit mode setting

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Currently the driver always sets the controller to dual data bit mode
for both tx and rx data in the profile mode control register even for
single data bit transfer. Luckily the opcode is set correctly according
to SPI transfer data bit width so it does not actually cause issues.

This change fixes the problem by setting tx and rx data bit mode field
correctly according to the actual SPI transfer tx and rx data bit width.

Fixes: 142168eba9dc ("spi: bcm63xx-hsspi: add bcm63xx HSSPI driver")
Signed-off-by: William Zhang <william.zhang@xxxxxxxxxxxx>
---

(no changes since v1)

 drivers/spi/spi-bcm63xx-hsspi.c | 13 +++++++++----
 1 file changed, 9 insertions(+), 4 deletions(-)

diff --git a/drivers/spi/spi-bcm63xx-hsspi.c b/drivers/spi/spi-bcm63xx-hsspi.c
index af51488659b8..bc700649d270 100644
--- a/drivers/spi/spi-bcm63xx-hsspi.c
+++ b/drivers/spi/spi-bcm63xx-hsspi.c
@@ -215,7 +215,7 @@ static int bcm63xx_hsspi_do_txrx(struct spi_device *spi, struct spi_transfer *t)
 	int step_size = HSSPI_BUFFER_LEN;
 	const u8 *tx = t->tx_buf;
 	u8 *rx = t->rx_buf;
-	u32 val;
+	u32 val = 0;
 	unsigned long limit;
 
 	bcm63xx_hsspi_set_clk(bs, spi, t->speed_hz);
@@ -233,11 +233,16 @@ static int bcm63xx_hsspi_do_txrx(struct spi_device *spi, struct spi_transfer *t)
 		step_size -= HSSPI_OPCODE_LEN;
 
 	if ((opcode == HSSPI_OP_READ && t->rx_nbits == SPI_NBITS_DUAL) ||
-	    (opcode == HSSPI_OP_WRITE && t->tx_nbits == SPI_NBITS_DUAL))
+	    (opcode == HSSPI_OP_WRITE && t->tx_nbits == SPI_NBITS_DUAL)) {
 		opcode |= HSSPI_OP_MULTIBIT;
 
-	__raw_writel(1 << MODE_CTRL_MULTIDATA_WR_SIZE_SHIFT |
-		     1 << MODE_CTRL_MULTIDATA_RD_SIZE_SHIFT | 0xff,
+		if (t->rx_nbits == SPI_NBITS_DUAL)
+			val |= 1 << MODE_CTRL_MULTIDATA_RD_SIZE_SHIFT;
+		if (t->tx_nbits == SPI_NBITS_DUAL)
+			val |= 1 << MODE_CTRL_MULTIDATA_WR_SIZE_SHIFT;
+	}
+
+	__raw_writel(val | 0xff,
 		     bs->regs + HSSPI_PROFILE_MODE_CTRL_REG(chip_select));
 
 	while (pending > 0) {
-- 
2.37.3




[Index of Archives]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux