Add the missing required DT property `atmel,usart-mode` to the serial
nodes of Atmel/Microchip DT files.
Signed-off-by: Sergiu Moga <sergiu.moga@xxxxxxxxxxxxx>
---
v1 -> v3:
- Nothing, this patch was not here before
arch/arm/boot/dts/at91-sam9x60ek.dts | 1 +
arch/arm/boot/dts/at91rm9200.dtsi | 6 ++++++
arch/arm/boot/dts/at91sam9260.dtsi | 8 ++++++++
arch/arm/boot/dts/at91sam9261.dtsi | 5 +++++
arch/arm/boot/dts/at91sam9263.dtsi | 5 +++++
arch/arm/boot/dts/at91sam9g45.dtsi | 6 ++++++
arch/arm/boot/dts/at91sam9n12.dtsi | 6 ++++++
arch/arm/boot/dts/at91sam9rl.dtsi | 6 ++++++
arch/arm/boot/dts/at91sam9x5.dtsi | 7 +++++++
arch/arm/boot/dts/at91sam9x5_usart3.dtsi | 2 ++
arch/arm/boot/dts/sam9x60.dtsi | 2 ++
arch/arm/boot/dts/sama5d2.dtsi | 11 +++++++++++
arch/arm/boot/dts/sama5d3.dtsi | 7 +++++++
arch/arm/boot/dts/sama5d3_uart.dtsi | 3 +++
arch/arm/boot/dts/sama5d4.dtsi | 9 +++++++++
arch/arm/boot/dts/sama7g5.dtsi | 5 +++++
16 files changed, 89 insertions(+)
diff --git a/arch/arm/boot/dts/at91-sam9x60ek.dts b/arch/arm/boot/dts/at91-sam9x60ek.dts
index 67bce8d60908..4ba52ba11dc6 100644
--- a/arch/arm/boot/dts/at91-sam9x60ek.dts
+++ b/arch/arm/boot/dts/at91-sam9x60ek.dts
@@ -260,6 +260,7 @@ &flx5 {
uart1: serial@200 {
compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <14 IRQ_TYPE_LEVEL_HIGH 7>;
dmas = <&dma0
(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
diff --git a/arch/arm/boot/dts/at91rm9200.dtsi b/arch/arm/boot/dts/at91rm9200.dtsi
index d1181ead18e5..7a113325abb9 100644
--- a/arch/arm/boot/dts/at91rm9200.dtsi
+++ b/arch/arm/boot/dts/at91rm9200.dtsi
@@ -13,6 +13,7 @@
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
/ {
#address-cells = <1>;
@@ -596,6 +597,7 @@ pioD: gpio@fffffa00 {
dbgu: serial@fffff200 {
compatible = "atmel,at91rm9200-dbgu", "atmel,at91rm9200-usart";
reg = <0xfffff200 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_dbgu>;
@@ -607,6 +609,7 @@ dbgu: serial@fffff200 {
usart0: serial@fffc0000 {
compatible = "atmel,at91rm9200-usart";
reg = <0xfffc0000 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
@@ -620,6 +623,7 @@ usart0: serial@fffc0000 {
usart1: serial@fffc4000 {
compatible = "atmel,at91rm9200-usart";
reg = <0xfffc4000 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
@@ -633,6 +637,7 @@ usart1: serial@fffc4000 {
usart2: serial@fffc8000 {
compatible = "atmel,at91rm9200-usart";
reg = <0xfffc8000 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
@@ -646,6 +651,7 @@ usart2: serial@fffc8000 {
usart3: serial@fffcc000 {
compatible = "atmel,at91rm9200-usart";
reg = <0xfffcc000 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <23 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
diff --git a/arch/arm/boot/dts/at91sam9260.dtsi b/arch/arm/boot/dts/at91sam9260.dtsi
index 9d9820db9482..789fe356dbf6 100644
--- a/arch/arm/boot/dts/at91sam9260.dtsi
+++ b/arch/arm/boot/dts/at91sam9260.dtsi
@@ -11,6 +11,7 @@
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
/ {
#address-cells = <1>;
@@ -532,6 +533,7 @@ pioC: gpio@fffff800 {
dbgu: serial@fffff200 {
compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
reg = <0xfffff200 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_dbgu>;
@@ -543,6 +545,7 @@ dbgu: serial@fffff200 {
usart0: serial@fffb0000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffb0000 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
@@ -556,6 +559,7 @@ usart0: serial@fffb0000 {
usart1: serial@fffb4000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffb4000 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
@@ -569,6 +573,7 @@ usart1: serial@fffb4000 {
usart2: serial@fffb8000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffb8000 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
@@ -582,6 +587,7 @@ usart2: serial@fffb8000 {
usart3: serial@fffd0000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffd0000 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <23 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
@@ -595,6 +601,7 @@ usart3: serial@fffd0000 {
uart0: serial@fffd4000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffd4000 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <24 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
@@ -608,6 +615,7 @@ uart0: serial@fffd4000 {
uart1: serial@fffd8000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffd8000 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <25 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
diff --git a/arch/arm/boot/dts/at91sam9261.dtsi b/arch/arm/boot/dts/at91sam9261.dtsi
index 259aca565305..ee0bd1aceb3f 100644
--- a/arch/arm/boot/dts/at91sam9261.dtsi
+++ b/arch/arm/boot/dts/at91sam9261.dtsi
@@ -9,6 +9,7 @@
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
/ {
#address-cells = <1>;
@@ -179,6 +180,7 @@ i2c0: i2c@fffac000 {
usart0: serial@fffb0000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffb0000 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
@@ -192,6 +194,7 @@ usart0: serial@fffb0000 {
usart1: serial@fffb4000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffb4000 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
@@ -205,6 +208,7 @@ usart1: serial@fffb4000 {
usart2: serial@fffb8000{
compatible = "atmel,at91sam9260-usart";
reg = <0xfffb8000 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
@@ -301,6 +305,7 @@ aic: interrupt-controller@fffff000 {
dbgu: serial@fffff200 {
compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
reg = <0xfffff200 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_dbgu>;
diff --git a/arch/arm/boot/dts/at91sam9263.dtsi b/arch/arm/boot/dts/at91sam9263.dtsi
index c080df8c2312..3ce9ea987312 100644
--- a/arch/arm/boot/dts/at91sam9263.dtsi
+++ b/arch/arm/boot/dts/at91sam9263.dtsi
@@ -9,6 +9,7 @@
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
/ {
#address-cells = <1>;
@@ -540,6 +541,7 @@ pioE: gpio@fffffa00 {
dbgu: serial@ffffee00 {
compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
reg = <0xffffee00 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_dbgu>;
@@ -551,6 +553,7 @@ dbgu: serial@ffffee00 {
usart0: serial@fff8c000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfff8c000 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
@@ -564,6 +567,7 @@ usart0: serial@fff8c000 {
usart1: serial@fff90000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfff90000 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
@@ -577,6 +581,7 @@ usart1: serial@fff90000 {
usart2: serial@fff94000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfff94000 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <9 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
diff --git a/arch/arm/boot/dts/at91sam9g45.dtsi b/arch/arm/boot/dts/at91sam9g45.dtsi
index 09794561c7ce..95f5d76234db 100644
--- a/arch/arm/boot/dts/at91sam9g45.dtsi
+++ b/arch/arm/boot/dts/at91sam9g45.dtsi
@@ -13,6 +13,7 @@
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
/ {
#address-cells = <1>;
@@ -675,6 +676,7 @@ pioE: gpio@fffffa00 {
dbgu: serial@ffffee00 {
compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
reg = <0xffffee00 0x200>;
interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
pinctrl-names = "default";
@@ -687,6 +689,7 @@ dbgu: serial@ffffee00 {
usart0: serial@fff8c000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfff8c000 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
@@ -700,6 +703,7 @@ usart0: serial@fff8c000 {
usart1: serial@fff90000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfff90000 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
@@ -713,6 +717,7 @@ usart1: serial@fff90000 {
usart2: serial@fff94000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfff94000 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <9 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
@@ -726,6 +731,7 @@ usart2: serial@fff94000 {
usart3: serial@fff98000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfff98000 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <10 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
diff --git a/arch/arm/boot/dts/at91sam9n12.dtsi b/arch/arm/boot/dts/at91sam9n12.dtsi
index 556f35ce49e3..83114d26f10d 100644
--- a/arch/arm/boot/dts/at91sam9n12.dtsi
+++ b/arch/arm/boot/dts/at91sam9n12.dtsi
@@ -11,6 +11,7 @@
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
/ {
#address-cells = <1>;
@@ -593,6 +594,7 @@ pioD: gpio@fffffa00 {
dbgu: serial@fffff200 {
compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
reg = <0xfffff200 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_dbgu>;
@@ -618,6 +620,7 @@ ssc0: ssc@f0010000 {
usart0: serial@f801c000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf801c000 0x4000>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <5 IRQ_TYPE_LEVEL_HIGH 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usart0>;
@@ -629,6 +632,7 @@ usart0: serial@f801c000 {
usart1: serial@f8020000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf8020000 0x4000>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usart1>;
@@ -640,6 +644,7 @@ usart1: serial@f8020000 {
usart2: serial@f8024000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf8024000 0x4000>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usart2>;
@@ -651,6 +656,7 @@ usart2: serial@f8024000 {
usart3: serial@f8028000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf8028000 0x4000>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usart3>;
diff --git a/arch/arm/boot/dts/at91sam9rl.dtsi b/arch/arm/boot/dts/at91sam9rl.dtsi
index 12c634811820..364a2ff0a763 100644
--- a/arch/arm/boot/dts/at91sam9rl.dtsi
+++ b/arch/arm/boot/dts/at91sam9rl.dtsi
@@ -11,6 +11,7 @@
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/pwm/pwm.h>
+#include <dt-bindings/mfd/at91-usart.h>
/ {
#address-cells = <1>;
@@ -175,6 +176,7 @@ i2c1: i2c@fffac000 {
usart0: serial@fffb0000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffb0000 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
@@ -188,6 +190,7 @@ usart0: serial@fffb0000 {
usart1: serial@fffb4000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffb4000 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
@@ -201,6 +204,7 @@ usart1: serial@fffb4000 {
usart2: serial@fffb8000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffb8000 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
@@ -214,6 +218,7 @@ usart2: serial@fffb8000 {
usart3: serial@fffbc000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfffbc000 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <9 IRQ_TYPE_LEVEL_HIGH 5>;
atmel,use-dma-rx;
atmel,use-dma-tx;
@@ -322,6 +327,7 @@ aic: interrupt-controller@fffff000 {
dbgu: serial@fffff200 {
compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
reg = <0xfffff200 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_dbgu>;
diff --git a/arch/arm/boot/dts/at91sam9x5.dtsi b/arch/arm/boot/dts/at91sam9x5.dtsi
index ea3b11336c79..0c26c925761b 100644
--- a/arch/arm/boot/dts/at91sam9x5.dtsi
+++ b/arch/arm/boot/dts/at91sam9x5.dtsi
@@ -13,6 +13,7 @@
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
/ {
#address-cells = <1>;
@@ -674,6 +675,7 @@ mmc1: mmc@f000c000 {
dbgu: serial@fffff200 {
compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
reg = <0xfffff200 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <1 IRQ_TYPE_LEVEL_HIGH 7>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_dbgu>;
@@ -688,6 +690,7 @@ dbgu: serial@fffff200 {
usart0: serial@f801c000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf801c000 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <5 IRQ_TYPE_LEVEL_HIGH 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usart0>;
@@ -702,6 +705,7 @@ usart0: serial@f801c000 {
usart1: serial@f8020000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf8020000 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usart1>;
@@ -716,6 +720,7 @@ usart1: serial@f8020000 {
usart2: serial@f8024000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf8024000 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usart2>;
@@ -775,6 +780,7 @@ i2c2: i2c@f8018000 {
uart0: serial@f8040000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf8040000 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <15 IRQ_TYPE_LEVEL_HIGH 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart0>;
@@ -786,6 +792,7 @@ uart0: serial@f8040000 {
uart1: serial@f8044000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf8044000 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <16 IRQ_TYPE_LEVEL_HIGH 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
diff --git a/arch/arm/boot/dts/at91sam9x5_usart3.dtsi b/arch/arm/boot/dts/at91sam9x5_usart3.dtsi
index 098d3fef5c37..a47c765e1b20 100644
--- a/arch/arm/boot/dts/at91sam9x5_usart3.dtsi
+++ b/arch/arm/boot/dts/at91sam9x5_usart3.dtsi
@@ -8,6 +8,7 @@
#include <dt-bindings/pinctrl/at91.h>
#include <dt-bindings/interrupt-controller/irq.h>
+#include <dt-bindings/mfd/at91-usart.h>
/ {
aliases {
@@ -44,6 +45,7 @@ pinctrl_usart3_sck: usart3_sck-0 {
usart3: serial@f8028000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf8028000 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <8 IRQ_TYPE_LEVEL_HIGH 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_usart3>;
diff --git a/arch/arm/boot/dts/sam9x60.dtsi b/arch/arm/boot/dts/sam9x60.dtsi
index d3f60f6a456d..8f5477e307dd 100644
--- a/arch/arm/boot/dts/sam9x60.dtsi
+++ b/arch/arm/boot/dts/sam9x60.dtsi
@@ -12,6 +12,7 @@
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
#include <dt-bindings/mfd/atmel-flexcom.h>
/ {
@@ -583,6 +584,7 @@ aic: interrupt-controller@fffff100 {
dbgu: serial@fffff200 {
compatible = "microchip,sam9x60-dbgu", "microchip,sam9x60-usart", "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
reg = <0xfffff200 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <47 IRQ_TYPE_LEVEL_HIGH 7>;
dmas = <&dma0
(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
diff --git a/arch/arm/boot/dts/sama5d2.dtsi b/arch/arm/boot/dts/sama5d2.dtsi
index 2c50a021aa76..14c35c12a115 100644
--- a/arch/arm/boot/dts/sama5d2.dtsi
+++ b/arch/arm/boot/dts/sama5d2.dtsi
@@ -9,6 +9,7 @@
#include <dt-bindings/dma/at91.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
#include <dt-bindings/iio/adc/at91-sama5d2_adc.h>
/ {
@@ -441,6 +442,7 @@ pdmic: pdmic@f8018000 {
uart0: serial@f801c000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf801c000 0x100>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <24 IRQ_TYPE_LEVEL_HIGH 7>;
dmas = <&dma0
(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
@@ -457,6 +459,7 @@ AT91_XDMAC_DT_PERID(35))>,
uart1: serial@f8020000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf8020000 0x100>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <25 IRQ_TYPE_LEVEL_HIGH 7>;
dmas = <&dma0
(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
@@ -473,6 +476,7 @@ AT91_XDMAC_DT_PERID(37))>,
uart2: serial@f8024000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf8024000 0x100>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <26 IRQ_TYPE_LEVEL_HIGH 7>;
dmas = <&dma0
(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
@@ -530,6 +534,7 @@ flx0: flexcom@f8034000 {
uart5: serial@200 {
compatible = "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <19 IRQ_TYPE_LEVEL_HIGH 7>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 19>;
clock-names = "usart";
@@ -600,6 +605,7 @@ flx1: flexcom@f8038000 {
uart6: serial@200 {
compatible = "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <20 IRQ_TYPE_LEVEL_HIGH 7>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 20>;
clock-names = "usart";
@@ -769,6 +775,7 @@ AT91_XDMAC_DT_PERID(8))>,
uart3: serial@fc008000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfc008000 0x100>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <27 IRQ_TYPE_LEVEL_HIGH 7>;
dmas = <&dma1
(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
@@ -785,6 +792,7 @@ AT91_XDMAC_DT_PERID(41))>,
uart4: serial@fc00c000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfc00c000 0x100>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
dmas = <&dma0
(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1) |
AT91_XDMAC_DT_PERID(43))>,
@@ -810,6 +818,7 @@ flx2: flexcom@fc010000 {
uart7: serial@200 {
compatible = "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <21 IRQ_TYPE_LEVEL_HIGH 7>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 21>;
clock-names = "usart";
@@ -880,6 +889,7 @@ flx3: flexcom@fc014000 {
uart8: serial@200 {
compatible = "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 22>;
clock-names = "usart";
@@ -951,6 +961,7 @@ flx4: flexcom@fc018000 {
uart9: serial@200 {
compatible = "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 23>;
clock-names = "usart";
diff --git a/arch/arm/boot/dts/sama5d3.dtsi b/arch/arm/boot/dts/sama5d3.dtsi
index 2d0935ad2225..bde8e92d60bb 100644
--- a/arch/arm/boot/dts/sama5d3.dtsi
+++ b/arch/arm/boot/dts/sama5d3.dtsi
@@ -12,6 +12,7 @@
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/gpio/gpio.h>
#include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
/ {
#address-cells = <1>;
@@ -194,6 +195,7 @@ i2c1: i2c@f0018000 {
usart0: serial@f001c000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf001c000 0x100>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <12 IRQ_TYPE_LEVEL_HIGH 5>;
dmas = <&dma0 2 AT91_DMA_CFG_PER_ID(3)>,
<&dma0 2 (AT91_DMA_CFG_PER_ID(4) | AT91_DMA_CFG_FIFOCFG_ASAP)>;
@@ -208,6 +210,7 @@ usart0: serial@f001c000 {
usart1: serial@f0020000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf0020000 0x100>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <13 IRQ_TYPE_LEVEL_HIGH 5>;
dmas = <&dma0 2 AT91_DMA_CFG_PER_ID(5)>,
<&dma0 2 (AT91_DMA_CFG_PER_ID(6) | AT91_DMA_CFG_FIFOCFG_ASAP)>;
@@ -222,6 +225,7 @@ usart1: serial@f0020000 {
uart0: serial@f0024000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf0024000 0x100>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <16 IRQ_TYPE_LEVEL_HIGH 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart0>;
@@ -356,6 +360,7 @@ i2c2: i2c@f801c000 {
usart2: serial@f8020000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf8020000 0x100>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <14 IRQ_TYPE_LEVEL_HIGH 5>;
dmas = <&dma1 2 AT91_DMA_CFG_PER_ID(7)>,
<&dma1 2 (AT91_DMA_CFG_PER_ID(8) | AT91_DMA_CFG_FIFOCFG_ASAP)>;
@@ -370,6 +375,7 @@ usart2: serial@f8020000 {
usart3: serial@f8024000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf8024000 0x100>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <15 IRQ_TYPE_LEVEL_HIGH 5>;
dmas = <&dma1 2 AT91_DMA_CFG_PER_ID(9)>,
<&dma1 2 (AT91_DMA_CFG_PER_ID(10) | AT91_DMA_CFG_FIFOCFG_ASAP)>;
@@ -464,6 +470,7 @@ ramc0: ramc@ffffea00 {
dbgu: serial@ffffee00 {
compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
reg = <0xffffee00 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <2 IRQ_TYPE_LEVEL_HIGH 7>;
dmas = <&dma1 2 AT91_DMA_CFG_PER_ID(13)>,
<&dma1 2 (AT91_DMA_CFG_PER_ID(14) | AT91_DMA_CFG_FIFOCFG_ASAP)>;
diff --git a/arch/arm/boot/dts/sama5d3_uart.dtsi b/arch/arm/boot/dts/sama5d3_uart.dtsi
index a3eaba995cf4..44d1173f2ffb 100644
--- a/arch/arm/boot/dts/sama5d3_uart.dtsi
+++ b/arch/arm/boot/dts/sama5d3_uart.dtsi
@@ -9,6 +9,7 @@
#include <dt-bindings/pinctrl/at91.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/clock/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
/ {
aliases {
@@ -39,6 +40,7 @@ pinctrl_uart1: uart1-0 {
uart0: serial@f0024000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf0024000 0x100>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <16 IRQ_TYPE_LEVEL_HIGH 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart0>;
@@ -50,6 +52,7 @@ uart0: serial@f0024000 {
uart1: serial@f8028000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf8028000 0x100>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <17 IRQ_TYPE_LEVEL_HIGH 5>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_uart1>;
diff --git a/arch/arm/boot/dts/sama5d4.dtsi b/arch/arm/boot/dts/sama5d4.dtsi
index 1e5c01898ccf..af62157ae214 100644
--- a/arch/arm/boot/dts/sama5d4.dtsi
+++ b/arch/arm/boot/dts/sama5d4.dtsi
@@ -8,6 +8,7 @@
#include <dt-bindings/clock/at91.h>
#include <dt-bindings/dma/at91.h>
+#include <dt-bindings/mfd/at91-usart.h>
#include <dt-bindings/pinctrl/at91.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/gpio/gpio.h>
@@ -278,6 +279,7 @@ mmc0: mmc@f8000000 {
uart0: serial@f8004000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf8004000 0x100>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <27 IRQ_TYPE_LEVEL_HIGH 5>;
dmas = <&dma0
(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
@@ -437,6 +439,7 @@ sfr: sfr@f8028000 {
usart0: serial@f802c000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf802c000 0x100>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <6 IRQ_TYPE_LEVEL_HIGH 5>;
dmas = <&dma0
(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
@@ -455,6 +458,7 @@ usart0: serial@f802c000 {
usart1: serial@f8030000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xf8030000 0x100>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <7 IRQ_TYPE_LEVEL_HIGH 5>;
dmas = <&dma0
(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
@@ -490,6 +494,7 @@ mmc1: mmc@fc000000 {
uart1: serial@fc004000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfc004000 0x100>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <28 IRQ_TYPE_LEVEL_HIGH 5>;
dmas = <&dma0
(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
@@ -508,6 +513,7 @@ uart1: serial@fc004000 {
usart2: serial@fc008000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfc008000 0x100>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <29 IRQ_TYPE_LEVEL_HIGH 5>;
dmas = <&dma1
(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
@@ -526,6 +532,7 @@ usart2: serial@fc008000 {
usart3: serial@fc00c000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfc00c000 0x100>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <30 IRQ_TYPE_LEVEL_HIGH 5>;
dmas = <&dma1
(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
@@ -544,6 +551,7 @@ usart3: serial@fc00c000 {
usart4: serial@fc010000 {
compatible = "atmel,at91sam9260-usart";
reg = <0xfc010000 0x100>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <31 IRQ_TYPE_LEVEL_HIGH 5>;
dmas = <&dma1
(AT91_XDMAC_DT_MEM_IF(0) | AT91_XDMAC_DT_PER_IF(1)
@@ -770,6 +778,7 @@ rtc@fc0686b0 {
dbgu: serial@fc069000 {
compatible = "atmel,at91sam9260-dbgu", "atmel,at91sam9260-usart";
reg = <0xfc069000 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <45 IRQ_TYPE_LEVEL_HIGH 7>;
pinctrl-names = "default";
pinctrl-0 = <&pinctrl_dbgu>;
diff --git a/arch/arm/boot/dts/sama7g5.dtsi b/arch/arm/boot/dts/sama7g5.dtsi
index 249f9c640b6c..7bd8ae8e8d38 100644
--- a/arch/arm/boot/dts/sama7g5.dtsi
+++ b/arch/arm/boot/dts/sama7g5.dtsi
@@ -14,6 +14,7 @@
#include <dt-bindings/clock/at91.h>
#include <dt-bindings/dma/at91.h>
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/mfd/at91-usart.h>
/ {
model = "Microchip SAMA7G5 family SoC";
@@ -603,6 +604,7 @@ flx0: flexcom@e1818000 {
uart0: serial@200 {
compatible = "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 38>;
clock-names = "usart";
@@ -651,6 +653,7 @@ flx3: flexcom@e1824000 {
uart3: serial@200 {
compatible = "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 41>;
clock-names = "usart";
@@ -694,6 +697,7 @@ flx4: flexcom@e2018000 {
uart4: serial@200 {
compatible = "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 42>;
clock-names = "usart";
@@ -719,6 +723,7 @@ flx7: flexcom@e2024000 {
uart7: serial@200 {
compatible = "atmel,at91sam9260-usart";
reg = <0x200 0x200>;
+ atmel,usart-mode = <AT91_USART_MODE_SERIAL>;
interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&pmc PMC_TYPE_PERIPHERAL 45>;
clock-names = "usart";
--
2.34.1
[PATCH v3 03/14] ARM: dts: at91: Add `atmel,usart-mode` required property to serial nodes
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
- Subject: [PATCH v3 03/14] ARM: dts: at91: Add `atmel,usart-mode` required property to serial nodes
- From: Sergiu Moga <sergiu.moga@xxxxxxxxxxxxx>
- Date: Tue, 13 Sep 2022 17:21:55 +0300
- Cc: <devicetree@xxxxxxxxxxxxxxx>, <linux-arm-kernel@xxxxxxxxxxxxxxxxxxx>, <linux-kernel@xxxxxxxxxxxxxxx>, <linux-spi@xxxxxxxxxxxxxxx>, <linux-serial@xxxxxxxxxxxxxxx>, <linux-clk@xxxxxxxxxxxxxxx>
- In-reply-to: <20220913142205.162399-1-sergiu.moga@microchip.com>
- References: <20220913142205.162399-1-sergiu.moga@microchip.com>
- Follow-Ups:
- References:
- [PATCH v3 00/14] Make atmel serial driver aware of GCLK
- From: Sergiu Moga
- [PATCH v3 00/14] Make atmel serial driver aware of GCLK
- Prev by Date: Re: [PATCH v3 08/14] dt-bindings: mfd: atmel,sama5d2-flexcom: Add USART child node ref binding
- Next by Date: [PATCH v3 02/14] ARM: dts: at91: sam9x60ek: Add DBGU compatibles to uart1
- Previous by thread: Re: [PATCH v3 13/14] clk: at91: sama5d2: Add Generic Clocks for UART/USART
- Next by thread: Re: [PATCH v3 03/14] ARM: dts: at91: Add `atmel,usart-mode` required property to serial nodes
- Index(es):
 |