On Sat, 19 Feb 2022 06:45:43 PST (-0800), icenowy@xxxxxxxxxxxxx wrote:
在 2022-01-27星期四的 23:16 +0800，Icenowy Zheng写道：
This patchset adds support for Nuclei DemoSoC (which is an evaluation
platform made with Nuclei CPU cores and mainly peripherals in
original
Hummingbird E203 project, running on FPGA) with UX600 CPU cores.
Most patches are for DT bindings, the remaining ones are adding a
Kconfig option and some DTS/DTSI files. The last one is a workaround
for
a severe bug in currently released versions of UX600, which is found
in 5.17 kernel, in which Sv48 support is added to Linux.
Two non-technical patches are in this patchset too, for MAINTAINERS
and .mailmap items.
Ping, could any RISC-V maintainers review these patches, especially the
SATP workaround one?
Sorry, I remember having written this but I guess it got lost. IIRC my
main worry here was that, at least as far as I can tell, DemoSOC is an
FPGA development board. If this is actually in production somewhere
then it's a different story, but IIUC the general rule is not to accept
code for development hardware that can be updated.
Assuming DemoSOC can be updated, I'd also argue that we should have some
sort of version attached to it in DT entries. Without some versioning
we'll end up lost when trying to later determine what we're actually
running on.
As far as the errata goes: it looks fine to me, but I'd like to see some
sort of description of what the errata actually is (ie, some
documentation from the manufacturer). I know that's not always
possible, but without some desciption of what the bug is it gets tricky
to mainain this sort of stuff. For example: we've got sv57 patches
now, so how do I know what to do with them on this target?
Icenowy Zheng (12):
dt-bindings: vendor-prefixes: add Nuclei
RISC-V: add Nuclei SoC Kconfig option
dt-bindings: riscv: add compatible strings for Nuclei UX600 series
dt-bindings: timer: add compatible for Nuclei UX600 CLINT-compat
timer
dt-bindings: interrupt-controller: add compatible string for UX600
PLIC
dt-bindings: serial: add compatible string for Nuclei DemoSoC UART
dt-bindings: spi: add compatible string for Nuclei DemoSoC SPI
dt-bindings: riscv: add binding for Nuclei platform boards
riscv: dts: add device tree for Nuclei DemoSoC w/ UX600 on DDR200T
RISC-V: workaround Nuclei UX600 cores with broken SATP CSR
MAINTAINERS: add myself as Nuclei SoCs/CPUs supporter
mailmap: add Icenowy Zheng's Nuclei mail addresses
.mailmap | 1 +
.../sifive,plic-1.0.0.yaml | 1 +
.../devicetree/bindings/riscv/cpus.yaml | 7 ++
.../devicetree/bindings/riscv/nuclei.yaml | 27 ++++++++
.../bindings/serial/sifive-serial.yaml | 1 +
.../devicetree/bindings/spi/spi-sifive.yaml | 1 +
.../bindings/timer/sifive,clint.yaml | 1 +
.../devicetree/bindings/vendor-prefixes.yaml | 2 +
MAINTAINERS | 7 ++
arch/riscv/Kconfig.socs | 6 ++
arch/riscv/boot/dts/Makefile | 1 +
arch/riscv/boot/dts/nuclei/Makefile | 2 +
.../dts/nuclei/nuclei-demosoc-ddr200t.dtsi | 41 ++++++++++++
.../nuclei/nuclei-demosoc-ux600-ddr200t.dts | 13 ++++
.../boot/dts/nuclei/nuclei-demosoc-ux600.dtsi | 49 ++++++++++++++
.../riscv/boot/dts/nuclei/nuclei-demosoc.dtsi | 67
+++++++++++++++++++
arch/riscv/include/asm/vendorid_list.h | 1 +
arch/riscv/mm/init.c | 17 +++++
18 files changed, 245 insertions(+)
create mode 100644
Documentation/devicetree/bindings/riscv/nuclei.yaml
create mode 100644 arch/riscv/boot/dts/nuclei/Makefile
create mode 100644 arch/riscv/boot/dts/nuclei/nuclei-demosoc-
ddr200t.dtsi
create mode 100644 arch/riscv/boot/dts/nuclei/nuclei-demosoc-ux600-
ddr200t.dts
create mode 100644 arch/riscv/boot/dts/nuclei/nuclei-demosoc-
ux600.dtsi
create mode 100644 arch/riscv/boot/dts/nuclei/nuclei-demosoc.dtsi
