Hi Dmitry,
I probably will not give you a fully detailed review, but here are
some first points.
But before that, you probably want to also CC some of the SPI folks
that are used to review SPI drivers (Mark and the spi list)
On Thu, Dec 30, 2021 at 12:11 AM Dmitry Antipov <daantipov@xxxxxxxxx> wrote:
>
> This driver follows the HID Over SPI Protocol Specification 1.0. The
> initial version of the driver does not support: 1) multi-fragment input
> reports, 2) sending GET_INPUT and COMMAND output report types and
> processing their respective acknowledge input reports, and 3) device
> sleep power state.
As mentioned in my cover letter reply, please add a link to the
documentation (or at least a somewhat stable link on the msdn website)
we can quickly refer to.
>
> Signed-off-by: Dmitry Antipov <dmanti@xxxxxxxxxxxxx>
> ---
> arch/arm64/configs/defconfig | 1 +
> drivers/hid/Kconfig | 2 +
> drivers/hid/Makefile | 1 +
> drivers/hid/spi-hid/Kconfig | 25 +
> drivers/hid/spi-hid/Makefile | 12 +
> drivers/hid/spi-hid/spi-hid-core.c | 1487 +++++++++++++++++++++++++++
> drivers/hid/spi-hid/spi-hid-core.h | 201 ++++
> drivers/hid/spi-hid/spi-hid_trace.h | 197 ++++
> drivers/hid/spi-hid/trace.c | 11 +
> 9 files changed, 1937 insertions(+)
> create mode 100644 drivers/hid/spi-hid/Kconfig
> create mode 100644 drivers/hid/spi-hid/Makefile
> create mode 100644 drivers/hid/spi-hid/spi-hid-core.c
> create mode 100644 drivers/hid/spi-hid/spi-hid-core.h
> create mode 100644 drivers/hid/spi-hid/spi-hid_trace.h
> create mode 100644 drivers/hid/spi-hid/trace.c
>
> diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
> index f2e2b9bdd702..25249a4b0c8a 100644
> --- a/arch/arm64/configs/defconfig
> +++ b/arch/arm64/configs/defconfig
> @@ -805,6 +805,7 @@ CONFIG_SND_AUDIO_GRAPH_CARD=m
> CONFIG_HID_MULTITOUCH=m
> CONFIG_I2C_HID_ACPI=m
> CONFIG_I2C_HID_OF=m
> +CONFIG_SPI_HID=m
> CONFIG_USB_CONN_GPIO=m
> CONFIG_USB=y
> CONFIG_USB_OTG=y
> diff --git a/drivers/hid/Kconfig b/drivers/hid/Kconfig
> index a7c78ac96270..cd2c10703fcf 100644
> --- a/drivers/hid/Kconfig
> +++ b/drivers/hid/Kconfig
> @@ -1262,6 +1262,8 @@ source "drivers/hid/usbhid/Kconfig"
>
> source "drivers/hid/i2c-hid/Kconfig"
>
> +source "drivers/hid/spi-hid/Kconfig"
> +
> source "drivers/hid/intel-ish-hid/Kconfig"
>
> source "drivers/hid/amd-sfh-hid/Kconfig"
> diff --git a/drivers/hid/Makefile b/drivers/hid/Makefile
> index 55a6fa3eca5a..caf418dda343 100644
> --- a/drivers/hid/Makefile
> +++ b/drivers/hid/Makefile
> @@ -144,6 +144,7 @@ obj-$(CONFIG_USB_MOUSE) += usbhid/
> obj-$(CONFIG_USB_KBD) += usbhid/
>
> obj-$(CONFIG_I2C_HID_CORE) += i2c-hid/
> +obj-$(CONFIG_SPI_HID) += spi-hid/
>
> obj-$(CONFIG_INTEL_ISH_HID) += intel-ish-hid/
> obj-$(INTEL_ISH_FIRMWARE_DOWNLOADER) += intel-ish-hid/
> diff --git a/drivers/hid/spi-hid/Kconfig b/drivers/hid/spi-hid/Kconfig
> new file mode 100644
> index 000000000000..5b34e51edc76
> --- /dev/null
> +++ b/drivers/hid/spi-hid/Kconfig
> @@ -0,0 +1,25 @@
> +#
> +# Copyright (c) 2021 Microsoft Corporation
> +#
> +# This program is free software; you can redistribute it and/or modify it
> +# under the terms of the GNU General Public License version 2 as published by
> +# the Free Software Foundation.
> +#
> +menu "SPI HID support"
> + depends on SPI
> +
> +config SPI_HID
> + tristate "HID over SPI transport layer"
> + default n
> + depends on SPI && INPUT
This first implementation relies on OF too.
> + select HID
> + help
> + Say Y here if you use a keyboard, a touchpad, a touchscreen, or any
> + other HID based devices which is connected to your computer via SPI.
> +
> + If unsure, say N.
> +
> + This support is also available as a module. If so, the module
> + will be called spi-hid.
> +
> +endmenu
> diff --git a/drivers/hid/spi-hid/Makefile b/drivers/hid/spi-hid/Makefile
> new file mode 100644
> index 000000000000..5eae49219ab5
> --- /dev/null
> +++ b/drivers/hid/spi-hid/Makefile
> @@ -0,0 +1,12 @@
> +#
> +# Copyright (c) 2021 Microsoft Corporation
> +#
> +# This program is free software; you can redistribute it and/or modify it
> +# under the terms of the GNU General Public License version 2 as published by
> +# the Free Software Foundation.
> +#
> +# Makefile for the SPI input drivers
> +#
> +CFLAGS_trace.o = -I$(src)
> +obj-$(CONFIG_SPI_HID) += spi-hid.o
> +spi-hid-objs := spi-hid-core.o trace.o
> diff --git a/drivers/hid/spi-hid/spi-hid-core.c b/drivers/hid/spi-hid/spi-hid-core.c
> new file mode 100644
> index 000000000000..e672bbc30b26
> --- /dev/null
> +++ b/drivers/hid/spi-hid/spi-hid-core.c
> @@ -0,0 +1,1487 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * HID over SPI protocol implementation
> + * spi-hid-core.h
spi-hid-core.c :)
> + *
> + * Copyright (c) 2021 Microsoft Corporation
> + *
> + * This code is partly based on "HID over I2C protocol implementation:
> + *
> + * Copyright (c) 2012 Benjamin Tissoires <benjamin.tissoires@xxxxxxxxx>
> + * Copyright (c) 2012 Ecole Nationale de l'Aviation Civile, France
> + * Copyright (c) 2012 Red Hat, Inc
> + *
> + * which in turn is partly based on "USB HID support for Linux":
> + *
> + * Copyright (c) 1999 Andreas Gal
> + * Copyright (c) 2000-2005 Vojtech Pavlik <vojtech@xxxxxxx>
> + * Copyright (c) 2005 Michael Haboustak <mike-@xxxxxxxxxxxx> for Concept2, Inc
> + * Copyright (c) 2007-2008 Oliver Neukum
> + * Copyright (c) 2006-2010 Jiri Kosina
> + *
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms of the GNU General Public License version 2 as published by
> + * the Free Software Foundation.
I think you can drop that last paragraph given that you gave the SPDX
line at the beginning of the file.
> + */
> +
> +#include <linux/crc32.h>
> +#include <linux/delay.h>
> +#include <linux/device.h>
> +#include <linux/dma-mapping.h>
> +#include <linux/err.h>
> +#include <linux/gpio/consumer.h>
> +#include <linux/hid.h>
> +#include <linux/input.h>
> +#include <linux/interrupt.h>
> +#include <linux/irq.h>
> +#include <linux/jiffies.h>
> +#include <linux/kernel.h>
> +#include <linux/list.h>
> +#include <linux/module.h>
> +#include <linux/mutex.h>
> +#include <linux/of.h>
> +#include <linux/regulator/consumer.h>
> +#include <linux/slab.h>
> +#include <linux/spi/spi.h>
> +#include <linux/string.h>
> +#include <linux/wait.h>
> +#include <linux/workqueue.h>
> +
> +#include "spi-hid-core.h"
> +#include "spi-hid_trace.h"
> +#include "../hid-ids.h"
> +
> +#define SPI_HID_MAX_RESET_ATTEMPTS 3
> +
> +static struct hid_ll_driver spi_hid_ll_driver;
> +
> +static void spi_hid_populate_read_approvals(struct spi_hid_host_config *conf,
> + __u8 *header_buf, __u8 *body_buf)
> +{
> + header_buf[0] = conf->read_opcode;
> + header_buf[1] = (conf->input_report_header_address >> 16) & 0xff;
> + header_buf[2] = (conf->input_report_header_address >> 8) & 0xff;
> + header_buf[3] = (conf->input_report_header_address >> 0) & 0xff;
> + header_buf[4] = SPI_HID_READ_APPROVAL_CONSTANT;
> +
> + body_buf[0] = conf->read_opcode;
> + body_buf[1] = (conf->input_report_body_address >> 16) & 0xff;
> + body_buf[2] = (conf->input_report_body_address >> 8) & 0xff;
> + body_buf[3] = (conf->input_report_body_address >> 0) & 0xff;
> + body_buf[4] = SPI_HID_READ_APPROVAL_CONSTANT;
> +}
> +
> +static void spi_hid_parse_dev_desc(struct spi_hid_device_desc_raw *raw,
> + struct spi_hid_device_descriptor *desc)
> +{
> + desc->hid_version = le16_to_cpu(raw->bcdVersion);
> + desc->report_descriptor_length = le16_to_cpu(raw->wReportDescLength);
> + desc->max_input_length = le16_to_cpu(raw->wMaxInputLength);
> + desc->max_output_length = le16_to_cpu(raw->wMaxOutputLength);
> +
> + /* FIXME: multi-fragment not supported, field below not used */
> + desc->max_fragment_length = le16_to_cpu(raw->wMaxFragmentLength);
> +
> + desc->vendor_id = le16_to_cpu(raw->wVendorID);
> + desc->product_id = le16_to_cpu(raw->wProductID);
> + desc->version_id = le16_to_cpu(raw->wVersionID);
> + desc->no_output_report_ack = le16_to_cpu(raw->wFlags) & BIT(0);
> +}
> +
> +static void spi_hid_populate_input_header(__u8 *buf,
> + struct spi_hid_input_header *header)
> +{
> + header->version = buf[0] & 0xf;
> + header->report_length = (buf[1] | ((buf[2] & 0x3f) << 8)) * 4;
> + header->last_fragment_flag = (buf[2] & 0x40) >> 6;
> + header->sync_const = buf[3];
> +}
> +
> +static void spi_hid_populate_input_body(__u8 *buf,
> + struct spi_hid_input_body *body)
> +{
> + body->report_type = buf[0];
> + body->content_length = buf[1] | (buf[2] << 8);
> + body->content_id = buf[3];
> +}
> +
> +static void spi_hid_input_report_prepare(struct spi_hid_input_buf *buf,
> + struct spi_hid_input_report *report)
> +{
> + struct spi_hid_input_header header;
> + struct spi_hid_input_body body;
> +
> + spi_hid_populate_input_header(buf->header, &header);
> + spi_hid_populate_input_body(buf->body, &body);
> + report->report_type = body.report_type;
> + report->content_length = body.content_length;
> + report->content_id = body.content_id;
> + report->content = buf->content;
> +}
> +
> +static void spi_hid_populate_output_header(__u8 *buf,
> + struct spi_hid_host_config *conf,
> + struct spi_hid_output_report *report)
> +{
> + buf[0] = conf->write_opcode;
> + buf[1] = (conf->output_report_address >> 16) & 0xff;
> + buf[2] = (conf->output_report_address >> 8) & 0xff;
> + buf[3] = (conf->output_report_address >> 0) & 0xff;
> + buf[4] = report->report_type;
> + buf[5] = report->content_length & 0xff;
> + buf[6] = (report->content_length >> 8) & 0xff;
> + buf[7] = report->content_id;
> +}
> +
> +static int spi_hid_input_async(struct spi_hid *shid, void *buf, u16 length,
> + void (*complete)(void *), bool is_header)
> +{
> + int ret;
> + struct device *dev = &shid->spi->dev;
> +
> + shid->input_transfer[0].tx_buf = is_header ? shid->read_approval_header :
> + shid->read_approval_body;
> + shid->input_transfer[0].len = SPI_HID_READ_APPROVAL_LEN;
> +
> + shid->input_transfer[1].rx_buf = buf;
> + shid->input_transfer[1].len = length;
> +
> + spi_message_init_with_transfers(&shid->input_message,
> + shid->input_transfer, 2);
> +
> + shid->input_message.complete = complete;
> + shid->input_message.context = shid;
> +
> + trace_spi_hid_input_async(shid,
> + shid->input_transfer[0].tx_buf,
> + shid->input_transfer[0].len,
> + shid->input_transfer[1].rx_buf,
> + shid->input_transfer[1].len, 0);
> +
> + ret = spi_async(shid->spi, &shid->input_message);
> + if (ret) {
> + dev_err(dev, "Error starting async transfer: %d, resetting\n",
> + ret);
> + schedule_work(&shid->error_work);
> +
> + shid->notify_device_driver_error_type =
> + HID_TRANSPORT_ERROR_TYPE_BUS_INPUT_TRANSFER_START;
> + shid->notify_device_driver_error_code = ret;
> + shid->notify_device_driver_handled = true;
> + schedule_work(&shid->notify_device_driver_work);
> + }
> +
> + return ret;
> +}
> +
> +static int spi_hid_output(struct spi_hid *shid, void *buf, u16 length)
> +{
> + struct spi_transfer transfer;
> + struct spi_message message;
> + int ret;
> +
> + memset(&transfer, 0, sizeof(transfer));
> +
> + transfer.tx_buf = buf;
> + transfer.len = length;
> +
> + spi_message_init_with_transfers(&message, &transfer, 1);
> +
> + /*
> + * REVISIT: Should output be asynchronous?
> + *
> + * According to Documentation/hid/hid-transport.rst, ->output_report()
> + * must be implemented as an asynchronous operation.
> + */
Apparently I messed up that one pretty badly: both documentation and
implementation in i2c-hid are from me and I ignored it blatantly in
i2c-hid :(
Maybe updating the documentation is enough by saying that this call
might be asynchronous so do not expect an immediate answer there.
> + trace_spi_hid_output_begin(shid, transfer.tx_buf,
> + transfer.len, NULL, 0, 0);
> +
> + ret = spi_sync(shid->spi, &message);
> +
> + trace_spi_hid_output_end(shid, transfer.tx_buf,
> + transfer.len, NULL, 0, ret);
> +
> + if (ret) {
> + shid->notify_device_driver_error_type =
> + HID_TRANSPORT_ERROR_TYPE_BUS_OUTPUT_TRANSFER;
> + shid->notify_device_driver_error_code = ret;
> + shid->notify_device_driver_handled = false;
> + schedule_work(&shid->notify_device_driver_work);
As mentioned in 3/5, why the need to have an async notification of
this error when your return code already carries that information?
> + }
> +
> + return ret;
> +}
> +
> +static const char *const spi_hid_power_mode_string(u8 power_state)
> +{
> + switch (power_state) {
> + case SPI_HID_POWER_MODE_ON:
> + return "d0";
> + case SPI_HID_POWER_MODE_SLEEP:
> + return "d2";
> + case SPI_HID_POWER_MODE_OFF:
> + return "d3";
> + case SPI_HID_POWER_MODE_WAKING_SLEEP:
> + return "d3*";
> + default:
> + return "unknown";
> + }
> +}
> +
> +static int spi_hid_power_down(struct spi_hid *shid)
> +{
> + struct device *dev = &shid->spi->dev;
> + int ret;
> +
> + if (regulator_is_enabled(shid->supply) == 0)
> + return 0;
> +
> + ret = regulator_disable(shid->supply);
> + if (ret) {
> + dev_err(dev, "failed to disable regulator\n");
> + shid->notify_device_driver_error_type =
> + HID_TRANSPORT_ERROR_TYPE_REGULATOR_DISABLE;
> + shid->notify_device_driver_error_code = ret;
> + shid->notify_device_driver_handled = false;
> + schedule_work(&shid->notify_device_driver_work);
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +static int spi_hid_power_up(struct spi_hid *shid)
> +{
> + int ret;
> +
> + if (regulator_is_enabled(shid->supply) > 0)
> + return 0;
> +
> + ret = regulator_enable(shid->supply);
> + if (ret) {
> + shid->notify_device_driver_error_type =
> + HID_TRANSPORT_ERROR_TYPE_REGULATOR_ENABLE;
> + shid->notify_device_driver_error_code = ret;
> + shid->notify_device_driver_handled = false;
> + schedule_work(&shid->notify_device_driver_work);
> + }
> +
> + /* FIXME: timeout values should come from DT */
Should be easy enough to fix in the final submission by following the
same than i2c-hid -> `post-power-on-delay-ms` as in
Documentation/devicetree/bindings/input/hid-over-i2c.txt
> + usleep_range(5000, 6000);
> +
> + return ret;
> +}
> +
> +static void spi_hid_suspend(struct spi_hid *shid)
> +{
> + struct device *dev = &shid->spi->dev;
> +
> + if (shid->power_state == SPI_HID_POWER_MODE_OFF)
> + return;
> +
> + disable_irq(shid->spi->irq);
> + shid->ready = false;
> + sysfs_notify(&dev->kobj, NULL, "ready");
> +
> + gpiod_set_value(shid->reset_gpio, 1);
> +
> + shid->power_state = SPI_HID_POWER_MODE_OFF;
> +}
> +
> +static void spi_hid_resume(struct spi_hid *shid)
> +{
> + if (shid->power_state == SPI_HID_POWER_MODE_ON)
> + return;
> +
> + shid->power_state = SPI_HID_POWER_MODE_ON;
> + enable_irq(shid->spi->irq);
> + shid->input_transfer_pending = 0;
> +
> + gpiod_set_value(shid->reset_gpio, 0);
> +
> + /* FIXME: timeout values should come from DT *
Hmm, this feels wrong to have that many sleeps (I assume you need to
call spi_hid_power_up().
> + usleep_range(5000, 6000);
> +}
> +
> +static struct hid_device *spi_hid_disconnect_hid(struct spi_hid *shid)
> +{
> + struct hid_device *hid = shid->hid;
> +
> + shid->hid = NULL;
> +
> + return hid;
> +}
> +
> +static void spi_hid_stop_hid(struct spi_hid *shid)
> +{
> + struct hid_device *hid;
> +
> + hid = spi_hid_disconnect_hid(shid);
> + if (hid) {
> + cancel_work_sync(&shid->create_device_work);
> + cancel_work_sync(&shid->refresh_device_work);
> + hid_destroy_device(hid);
> + }
> +}
> +
> +static void spi_hid_error_handler(struct spi_hid *shid)
> +{
> + struct device *dev = &shid->spi->dev;
> +
> + if (shid->power_state == SPI_HID_POWER_MODE_OFF)
> + return;
> +
> + dev_err(dev, "Error Handler\n");
This looks like a debug message that should be removed (FWIW, ftrace
should give you the same feedback).
> +
> + if (shid->attempts++ >= SPI_HID_MAX_RESET_ATTEMPTS) {
> + dev_err(dev, "unresponsive device, aborting.\n");
Just wondering if there is no spi_err() and other definitions
> + spi_hid_stop_hid(shid);
> + gpiod_set_value(shid->reset_gpio, 1);
> + spi_hid_power_down(shid);
> + return;
> + }
> +
> + shid->ready = false;
> + sysfs_notify(&dev->kobj, NULL, "ready");
> +
> + gpiod_set_value(shid->reset_gpio, 1);
> +
> + shid->power_state = SPI_HID_POWER_MODE_OFF;
> + shid->input_transfer_pending = 0;
> + cancel_work_sync(&shid->reset_work);
> +
> + /* FIXME: timeout values should come from DT */
Maybe we can have a common default value and let some hardware
specifics overwrite it (like we now do in i2c-hid with
i2c-hid-of-goodix.c for instance).
> + msleep(100);
> +
> + shid->power_state = SPI_HID_POWER_MODE_ON;
> +
> + gpiod_set_value(shid->reset_gpio, 0);
Shouldn't this set_value() be done in a helper that would also be
called in the .reset() callback?
> +}
> +
> +static void spi_hid_error_work(struct work_struct *work)
> +{
> + struct spi_hid *shid = container_of(work, struct spi_hid, error_work);
> +
> + spi_hid_error_handler(shid);
> +}
> +
> +static void spi_hid_notify_device_driver_work(struct work_struct *work)
> +{
> + struct spi_hid *shid = container_of(work, struct spi_hid,
> + notify_device_driver_work);
> +
> + if (shid->hid && shid->hid->driver &&
> + shid->hid->driver->on_transport_error) {
> + shid->hid->driver->on_transport_error(shid->hid,
> + shid->notify_device_driver_error_type,
> + shid->notify_device_driver_error_code,
> + shid->notify_device_driver_handled);
> + }
> +}
This function (or the equivalent with just the
device_initiated_reset() should likely be implemented in hid-core.c,
and have a definition in the generic hid.h header. All drivers that
make use of it will need to use it.
> +
> +static int spi_hid_send_output_report(struct spi_hid *shid,
> + struct spi_hid_output_report *report)
> +{
> + struct spi_hid_output_buf *buf = &shid->output;
> + struct device *dev = &shid->spi->dev;
> + u16 report_length;
> + u16 padded_length;
> + u8 padding;
> + int ret;
I really like the trace approach you are taking, why not add traces here?
> +
> + if (report->content_length > shid->desc.max_output_length) {
> + dev_err(dev, "Output report too big, content_length 0x%x\n",
> + report->content_length);
> + ret = -E2BIG;
> + goto out;
> + }
> +
> + spi_hid_populate_output_header(buf->header, &shid->conf, report);
> +
> + if (report->content_length)
> + memcpy(&buf->content, report->content, report->content_length);
> +
> + report_length = sizeof(buf->header) + report->content_length;
> + padded_length = round_up(report_length, 4);
> + padding = padded_length - report_length;
> + memset(&buf->content[report->content_length], 0, padding);
> +
> + ret = spi_hid_output(shid, buf, padded_length);
> + if (ret) {
> + dev_err(dev, "Failed output transfer\n");
> + goto out;
> + }
> +
> + return 0;
> +
> +out:
> + return ret;
> +}
> +
> +static int spi_hid_sync_request(struct spi_hid *shid,
> + struct spi_hid_output_report *report)
> +{
> + struct device *dev = &shid->spi->dev;
> + int ret = 0;
> +
> + ret = spi_hid_send_output_report(shid, report);
> + if (ret) {
> + dev_err(dev, "Failed to transfer output report\n");
> + return ret;
> + }
> +
> + mutex_unlock(&shid->lock);
> + ret = wait_for_completion_interruptible_timeout(&shid->output_done,
> + msecs_to_jiffies(1000));
> + mutex_lock(&shid->lock);
> + if (ret == 0) {
> + dev_err(dev, "Response timed out\n");
> + return -ETIMEDOUT;
> + }
> +
> + return 0;
> +}
> +
> +/**
> + * Handle the reset response from the FW by sending a request for the device
> + * descriptor.
> + */
> +static void spi_hid_reset_work(struct work_struct *work)
> +{
> + struct spi_hid *shid =
> + container_of(work, struct spi_hid, reset_work);
> + struct device *dev = &shid->spi->dev;
> + struct spi_hid_output_report report = {
> + .report_type = SPI_HID_OUTPUT_REPORT_TYPE_DEVICE_DESC_REQUEST,
> + .content_length = 0x0,
> + .content_id = SPI_HID_OUTPUT_REPORT_CONTENT_ID_DESC_REQUEST,
> + .content = NULL,
> + };
> + int ret;
> +
> + trace_spi_hid_reset_work(shid);
> +
> + dev_dbg(dev, "Reset Handler\n");
Please drop this one and use ftrace insteace (and/or tracepoints).
> +
> + if (shid->ready) {
> + dev_err(dev, "Spontaneous FW reset!");
> + shid->ready = false;
> + sysfs_notify(&dev->kobj, NULL, "ready");
> +
> + shid->notify_device_driver_error_type =
> + HID_TRANSPORT_ERROR_TYPE_DEVICE_INITIATED_RESET;
> + shid->notify_device_driver_error_code = 0;
> + shid->notify_device_driver_handled = false;
> + schedule_work(&shid->notify_device_driver_work);
> + }
> +
> + if (shid->power_state == SPI_HID_POWER_MODE_OFF)
> + return;
> +
> + if (flush_work(&shid->create_device_work))
> + dev_err(dev, "Reset handler waited for create_device_work");
> +
> + if (flush_work(&shid->refresh_device_work))
> + dev_err(dev, "Reset handler waited for refresh_device_work");
> +
> + mutex_lock(&shid->lock);
> + ret = spi_hid_sync_request(shid, &report);
> + mutex_unlock(&shid->lock);
> + if (ret) {
> + dev_WARN_ONCE(dev, true,
> + "Failed to send device descriptor request\n");
> + spi_hid_error_handler(shid);
> + }
> +}
> +
> +static int spi_hid_input_report_handler(struct spi_hid *shid,
> + struct spi_hid_input_buf *buf)
> +{
> + struct device *dev = &shid->spi->dev;
> + struct spi_hid_input_report r;
> + int ret;
> +
> + dev_dbg(dev, "Input Report Handler\n");
Please drop.
> +
> + trace_spi_hid_input_report_handler(shid);
> +
> + if (!shid->ready) {
> + dev_err(dev, "discarding input report, not ready!\n");
All those dev_err seem a little bit rude to the end user.
> + return 0;
> + }
> +
> + if (shid->refresh_in_progress) {
> + dev_err(dev, "discarding input report, refresh in progress!\n");
> + return 0;
> + }
> +
> + if (!shid->hid) {
> + dev_err(dev, "discarding input report, no HID device!\n");
> + return 0;
> + }
> +
> + spi_hid_input_report_prepare(buf, &r);
> +
> + ret = hid_input_report(shid->hid, HID_INPUT_REPORT,
> + r.content - 1,
> + r.content_length + 1, 1);
> +
> + if (ret == -ENODEV || ret == -EBUSY) {
> + dev_err(dev, "ignoring report --> %d\n", ret);
> + return 0;
> + } else if (ret) {
> + dev_err(dev, "Bad input report, error %d\n", ret);
> + }
> +
> + return ret;
> +}
> +
> +static void spi_hid_response_handler(struct spi_hid *shid,
> + struct spi_hid_input_buf *buf)
> +{
> + trace_spi_hid_response_handler(shid);
> + dev_dbg(&shid->spi->dev, "Response Handler\n");
> +
> + /* completion_done returns 0 if there are waiters, otherwise 1 */
> + if (completion_done(&shid->output_done)) {
> + dev_err(&shid->spi->dev, "Unexpected response report\n");
> + } else {
> + if (shid->input.body[0] ==
> + SPI_HID_INPUT_REPORT_TYPE_REPORT_DESC ||
> + shid->input.body[0] ==
> + SPI_HID_INPUT_REPORT_TYPE_GET_FEATURE_RESP) {
> + size_t response_length = (shid->input.body[1] |
> + (shid->input.body[2] << 8)) +
> + sizeof(shid->input.body);
> + memcpy(shid->response.body, shid->input.body,
> + response_length);
> + }
> + complete(&shid->output_done);
> + }
> +}
> +
> +/*
> + * This function returns the length of the report descriptor, or a negative
> + * error code if something went wrong.
> + */
> +static int spi_hid_report_descriptor_request(struct spi_hid *shid)
> +{
> + int ret;
> + struct device *dev = &shid->spi->dev;
> + struct spi_hid_output_report report = {
> + .report_type = SPI_HID_OUTPUT_REPORT_TYPE_REPORT_DESC_REQUEST,
> + .content_length = 0,
> + .content_id = SPI_HID_OUTPUT_REPORT_CONTENT_ID_DESC_REQUEST,
> + .content = NULL,
> + };
> +
> + ret = spi_hid_sync_request(shid, &report);
> + if (ret) {
> + dev_err(dev,
> + "Expected report descriptor not received! Error %d\n",
> + ret);
> + spi_hid_error_handler(shid);
> + goto out;
> + }
> +
> + ret = (shid->response.body[1] | (shid->response.body[2] << 8));
> + if (ret != shid->desc.report_descriptor_length) {
> + dev_err(dev,
> + "Received report descriptor length doesn't match device descriptor field, using min of the two\n");
> + ret = min_t(unsigned int, ret,
> + shid->desc.report_descriptor_length);
> + }
> +out:
> + return ret;
> +}
> +
> +static void spi_hid_process_input_report(struct spi_hid *shid,
> + struct spi_hid_input_buf *buf)
> +{
> + struct spi_hid_input_header header;
> + struct spi_hid_input_body body;
> + struct device *dev = &shid->spi->dev;
> + struct spi_hid_device_desc_raw *raw;
> + int ret;
> +
> + trace_spi_hid_process_input_report(shid);
> +
> + spi_hid_populate_input_header(buf->header, &header);
> + spi_hid_populate_input_body(buf->body, &body);
> +
> + dev_WARN_ONCE(dev, body.content_length > header.report_length,
> + "Bad body length %d > %d\n",
> + body.content_length, header.report_length);
> +
> + switch (body.report_type) {
> + case SPI_HID_INPUT_REPORT_TYPE_DATA:
> + ret = spi_hid_input_report_handler(shid, buf);
> + if (ret) {
> + shid->notify_device_driver_error_type =
> + HID_TRANSPORT_ERROR_TYPE_INPUT_REPORT_DATA;
> + shid->notify_device_driver_error_code = ret;
> + shid->notify_device_driver_handled = false;
> + schedule_work(&shid->notify_device_driver_work);
> + }
> + break;
> + case SPI_HID_INPUT_REPORT_TYPE_RESET_RESP:
> + schedule_work(&shid->reset_work);
> + break;
> + case SPI_HID_INPUT_REPORT_TYPE_DEVICE_DESC:
> + dev_dbg(dev, "Received device descriptor\n");
> + /* Mark the completion done to avoid timeout */
> + spi_hid_response_handler(shid, buf);
> +
> + /* Reset attempts at every device descriptor fetch */
> + shid->attempts = 0;
> +
> + raw = (struct spi_hid_device_desc_raw *)buf->content;
> +
> + /* Validate device descriptor length before parsing */
> + if (body.content_length != SPI_HID_DEVICE_DESCRIPTOR_LENGTH) {
> + dev_err(dev,
> + "Invalid content length %d, expected %d\n",
> + body.content_length,
> + SPI_HID_DEVICE_DESCRIPTOR_LENGTH);
> + schedule_work(&shid->error_work);
> + break;
> + }
> +
> + if (le16_to_cpu(raw->wDeviceDescLength) !=
> + SPI_HID_DEVICE_DESCRIPTOR_LENGTH) {
> + dev_err(dev,
> + "Invalid wDeviceDescLength %d, expected %d\n",
> + raw->wDeviceDescLength,
> + SPI_HID_DEVICE_DESCRIPTOR_LENGTH);
> + schedule_work(&shid->error_work);
> + break;
> + }
> +
> + spi_hid_parse_dev_desc(raw, &shid->desc);
> +
> + if (shid->desc.hid_version != SPI_HID_SUPPORTED_VERSION) {
> + dev_err(dev,
> + "Unsupported device descriptor version %4x\n",
> + shid->desc.hid_version);
> + schedule_work(&shid->error_work);
> + break;
> + }
> +
> + if (!shid->hid)
> + schedule_work(&shid->create_device_work);
> + else
> + schedule_work(&shid->refresh_device_work);
> +
> + break;
> + case SPI_HID_INPUT_REPORT_TYPE_SET_OUTPUT_REPORT_RESP:
> + if (shid->desc.no_output_report_ack) {
> + dev_err(dev, "Unexpected output report response\n");
> + break;
> + }
> + fallthrough;
> + case SPI_HID_INPUT_REPORT_TYPE_GET_FEATURE_RESP:
> + case SPI_HID_INPUT_REPORT_TYPE_SET_FEATURE_RESP:
> + if (!shid->ready) {
> + dev_err(dev,
> + "Unexpected response report while not ready: 0x%x\n",
> + body.report_type);
> + break;
> + }
> + fallthrough;
> + case SPI_HID_INPUT_REPORT_TYPE_REPORT_DESC:
> + spi_hid_response_handler(shid, buf);
> + break;
> + /*
> + * FIXME: sending GET_INPUT and COMMAND reports not supported, thus
> + * throw away responses to those, they should never come.
> + */
> + case SPI_HID_INPUT_REPORT_TYPE_GET_INPUT_REPORT_RESP:
> + case SPI_HID_INPUT_REPORT_TYPE_COMMAND_RESP:
> + dev_err(dev, "Not a supported report type: 0x%x\n",
> + body.report_type);
> + break;
> + default:
> + dev_err(dev, "Unknown input report: 0x%x\n",
> + body.report_type);
> + shid->notify_device_driver_error_type =
> + HID_TRANSPORT_ERROR_TYPE_REPORT_TYPE;
> + shid->notify_device_driver_error_code = -EPROTO;
> + shid->notify_device_driver_handled = false;
> + schedule_work(&shid->notify_device_driver_work);
> + break;
> + }
> +}
> +
> +static int spi_hid_bus_validate_header(struct spi_hid *shid,
> + struct spi_hid_input_header *header)
> +{
> + struct device *dev = &shid->spi->dev;
> +
> + if (header->version != SPI_HID_INPUT_HEADER_VERSION) {
> + dev_err(dev, "Unknown input report version (v 0x%x)\n",
> + header->version);
> + return -EINVAL;
> + }
> +
> + if (shid->desc.max_input_length != 0 &&
> + header->report_length > shid->desc.max_input_length) {
> + dev_err(dev, "Input report body size %u > max expected of %u\n",
> + header->report_length,
> + shid->desc.max_input_length);
> + return -EMSGSIZE;
> + }
> +
> + if (header->last_fragment_flag != 1) {
> + dev_err(dev, "Multi-fragment reports not supported\n");
> + return -EOPNOTSUPP;
> + }
> +
> + if (header->sync_const != SPI_HID_INPUT_HEADER_SYNC_BYTE) {
> + dev_err(dev, "Invalid input report sync constant (0x%x)\n",
> + header->sync_const);
> + return -EINVAL;
> + }
> +
> + return 0;
> +}
> +
> +static int spi_hid_create_device(struct spi_hid *shid)
> +{
> + struct hid_device *hid;
> + struct device *dev = &shid->spi->dev;
> + int ret;
> +
> + hid = hid_allocate_device();
> +
> + if (IS_ERR(hid)) {
> + dev_err(dev, "Failed to allocate hid device: %ld\n",
> + PTR_ERR(hid));
> + ret = PTR_ERR(hid);
> + return ret;
> + }
> +
> + hid->driver_data = shid->spi;
> + hid->ll_driver = &spi_hid_ll_driver;
> + hid->dev.parent = &shid->spi->dev;
> + hid->bus = BUS_SPI;
> + hid->version = shid->desc.hid_version;
> + hid->vendor = shid->desc.vendor_id;
> + hid->product = shid->desc.product_id;
> +
> + snprintf(hid->name, sizeof(hid->name), "spi %04hX:%04hX",
> + hid->vendor, hid->product);
> + strscpy(hid->phys, dev_name(&shid->spi->dev), sizeof(hid->phys));
> +
> + shid->hid = hid;
> +
> + ret = hid_add_device(hid);
> + if (ret) {
> + dev_err(dev, "Failed to add hid device: %d\n", ret);
> + /*
> + * We likely got here because report descriptor request timed
> + * out. Let's disconnect and destroy the hid_device structure.
> + */
> + hid = spi_hid_disconnect_hid(shid);
> + if (hid)
> + hid_destroy_device(hid);
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +static void spi_hid_create_device_work(struct work_struct *work)
> +{
> + struct spi_hid *shid =
> + container_of(work, struct spi_hid, create_device_work);
> + struct device *dev = &shid->spi->dev;
> + u8 prev_state = shid->power_state;
> + int ret;
> +
> + trace_spi_hid_create_device_work(shid);
> + dev_dbg(dev, "Create device work\n");
> +
> + ret = spi_hid_create_device(shid);
> + if (ret) {
> + dev_err(dev, "Failed to create hid device\n");
> + return;
> + }
> +
> + spi_hid_suspend(shid);
> +
> + shid->attempts = 0;
> +
> + dev_err(dev, "%s: %s -> %s\n", __func__,
> + spi_hid_power_mode_string(prev_state),
> + spi_hid_power_mode_string(shid->power_state));
This should at most be dev_info(), not dev_err. dev_dbg seems better even.
> +}
> +
> +static void spi_hid_refresh_device_work(struct work_struct *work)
> +{
> + struct spi_hid *shid =
> + container_of(work, struct spi_hid, refresh_device_work);
> + struct device *dev = &shid->spi->dev;
> + struct hid_device *hid;
> + int ret;
> + u32 new_crc32;
> +
> + trace_spi_hid_refresh_device_work(shid);
> + dev_dbg(dev, "Refresh device work\n");
> +
> + mutex_lock(&shid->lock);
> + ret = spi_hid_report_descriptor_request(shid);
> + mutex_unlock(&shid->lock);
> + if (ret < 0) {
> + dev_err(dev,
> + "Refresh: failed report descriptor request, error %d",
> + ret);
> + return;
> + }
> +
> + new_crc32 = crc32_le(0, (unsigned char const *)shid->response.content,
> + (size_t)ret);
> + if (new_crc32 == shid->report_descriptor_crc32) {
> + dev_dbg(dev, "Refresh device work - returning\n");
> + shid->ready = true;
> + sysfs_notify(&dev->kobj, NULL, "ready");
> + return;
> + }
> +
> + dev_err(dev, "Re-creating the HID device\n");
Please drop
> +
> + shid->report_descriptor_crc32 = new_crc32;
> + shid->refresh_in_progress = true;
> +
> + hid = spi_hid_disconnect_hid(shid);
> + if (hid)
> + hid_destroy_device(hid);
> +
> + ret = spi_hid_create_device(shid);
> + if (ret)
> + dev_err(dev, "Failed to create hid device\n");
> +
> + shid->refresh_in_progress = false;
> + shid->ready = true;
> + sysfs_notify(&dev->kobj, NULL, "ready");
> +}
> +
> +static void spi_hid_input_header_complete(void *_shid);
> +
> +static void spi_hid_input_body_complete(void *_shid)
> +{
> + struct spi_hid *shid = _shid;
> + struct device *dev = &shid->spi->dev;
> + unsigned long flags;
> + int ret;
> +
> + spin_lock_irqsave(&shid->input_lock, flags);
> +
> + if (shid->power_state == SPI_HID_POWER_MODE_OFF) {
> + dev_warn(dev,
> + "input body complete called while device is off\n");
> + goto out;
> + }
> +
> + trace_spi_hid_input_body_complete(shid,
> + shid->input_transfer[0].tx_buf,
> + shid->input_transfer[0].len,
> + shid->input_transfer[1].rx_buf,
> + shid->input_transfer[1].len,
> + shid->input_message.status);
> +
> + if (shid->input_message.status < 0) {
> + dev_warn(dev, "error reading body, resetting %d\n",
> + shid->input_message.status);
> + schedule_work(&shid->error_work);
> +
> + shid->notify_device_driver_error_type =
> + HID_TRANSPORT_ERROR_TYPE_BUS_INPUT_TRANSFER_BODY;
> + shid->notify_device_driver_error_code =
> + shid->input_message.status;
> + shid->notify_device_driver_handled = true;
> + schedule_work(&shid->notify_device_driver_work);
> + goto out;
> + }
> +
> + spi_hid_process_input_report(shid, &shid->input);
> +
> + if (--shid->input_transfer_pending) {
> + struct spi_hid_input_buf *buf = &shid->input;
> +
> + trace_spi_hid_header_transfer(shid);
> + ret = spi_hid_input_async(shid, buf->header,
> + sizeof(buf->header),
> + spi_hid_input_header_complete, true);
> + if (ret)
> + dev_err(dev, "failed to start header transfer %d\n",
> + ret);
> + }
> +
> +out:
> + spin_unlock_irqrestore(&shid->input_lock, flags);
> +}
> +
> +static void spi_hid_input_header_complete(void *_shid)
> +{
> + struct spi_hid *shid = _shid;
> + struct device *dev = &shid->spi->dev;
> + struct spi_hid_input_header header;
> + unsigned long flags;
> + int ret = 0;
> +
> + spin_lock_irqsave(&shid->input_lock, flags);
> +
> + if (shid->power_state == SPI_HID_POWER_MODE_OFF) {
> + dev_warn(dev,
> + "input header complete called while device is off\n");
> + goto out;
> + }
> +
> + trace_spi_hid_input_header_complete(shid,
> + shid->input_transfer[0].tx_buf,
> + shid->input_transfer[0].len,
> + shid->input_transfer[1].rx_buf,
> + shid->input_transfer[1].len,
> + shid->input_message.status);
> +
> + if (shid->input_message.status < 0) {
> + dev_warn(dev, "error reading header, resetting, error %d\n",
> + shid->input_message.status);
> + schedule_work(&shid->error_work);
> +
> + shid->notify_device_driver_error_type =
> + HID_TRANSPORT_ERROR_TYPE_BUS_INPUT_TRANSFER_HEADER;
> + shid->notify_device_driver_error_code =
> + shid->input_message.status;
> + shid->notify_device_driver_handled = true;
> + schedule_work(&shid->notify_device_driver_work);
> + goto out;
> + }
> + spi_hid_populate_input_header(shid->input.header, &header);
> +
> + ret = spi_hid_bus_validate_header(shid, &header);
> + if (ret) {
> + dev_err(dev, "failed to validate header: %d\n", ret);
> + print_hex_dump(KERN_ERR, "spi_hid: header buffer: ",
> + DUMP_PREFIX_NONE, 16, 1,
> + shid->input.header,
> + sizeof(shid->input.header),
> + false);
> +
> + shid->notify_device_driver_error_type =
> + HID_TRANSPORT_ERROR_TYPE_HEADER_DATA;
> + shid->notify_device_driver_error_code = ret;
> + shid->notify_device_driver_handled = false;
> + schedule_work(&shid->notify_device_driver_work);
> + goto out;
> + }
> +
> + ret = spi_hid_input_async(shid, shid->input.body, header.report_length,
> + spi_hid_input_body_complete, false);
> + if (ret)
> + dev_err(dev, "failed body async transfer: %d\n", ret);
> +
> +out:
> + if (ret)
> + shid->input_transfer_pending = 0;
> +
> + spin_unlock_irqrestore(&shid->input_lock, flags);
> +}
> +
> +static int spi_hid_get_request(struct spi_hid *shid, u8 content_id)
> +{
> + int ret;
> + struct device *dev = &shid->spi->dev;
> + struct spi_hid_output_report report = {
> + .report_type = SPI_HID_OUTPUT_REPORT_TYPE_HID_GET_FEATURE,
> + .content_length = 0,
> + .content_id = content_id,
> + .content = NULL,
> + };
> +
> + ret = spi_hid_sync_request(shid, &report);
> + if (ret) {
> + dev_err(dev,
> + "Expected get request response not received! Error %d\n",
> + ret);
> + shid->notify_device_driver_error_type =
> + HID_TRANSPORT_ERROR_TYPE_GET_FEATURE_RESPONSE;
> + shid->notify_device_driver_error_code = ret;
> + shid->notify_device_driver_handled = false;
> + schedule_work(&shid->notify_device_driver_work);
> + }
> +
> + return ret;
> +}
> +
> +static int spi_hid_set_request(struct spi_hid *shid,
> + u8 *arg_buf, u16 arg_len, u8 content_id)
> +{
> + struct spi_hid_output_report report = {
> + .report_type = SPI_HID_OUTPUT_REPORT_TYPE_HID_SET_FEATURE,
> + .content_length = arg_len,
> + .content_id = content_id,
> + .content = arg_buf,
> + };
> +
> + return spi_hid_sync_request(shid, &report);
> +}
> +
> +static irqreturn_t spi_hid_dev_irq(int irq, void *_shid)
> +{
> + struct spi_hid *shid = _shid;
> + struct device *dev = &shid->spi->dev;
> + int ret = 0;
> +
> + spin_lock(&shid->input_lock);
> + trace_spi_hid_dev_irq(shid, irq);
> +
> + if (shid->input_transfer_pending++)
> + goto out;
> +
> + trace_spi_hid_header_transfer(shid);
> + ret = spi_hid_input_async(shid, shid->input.header,
> + sizeof(shid->input.header),
> + spi_hid_input_header_complete, true);
> + if (ret)
> + dev_err(dev, "Failed to start header transfer: %d\n", ret);
> +
> +out:
> + spin_unlock(&shid->input_lock);
> +
> + return IRQ_HANDLED;
> +}
> +
> +/* hid_ll_driver interface functions */
> +
> +static int spi_hid_ll_start(struct hid_device *hid)
> +{
> + struct spi_device *spi = hid->driver_data;
> + struct spi_hid *shid = spi_get_drvdata(spi);
> +
> + if (shid->desc.max_input_length < HID_MIN_BUFFER_SIZE) {
> + dev_err(&shid->spi->dev,
> + "HID_MIN_BUFFER_SIZE > max_input_length (%d)\n",
> + shid->desc.max_input_length);
> + return -EINVAL;
> + }
> +
> + return 0;
> +}
> +
> +static void spi_hid_ll_stop(struct hid_device *hid)
> +{
> + hid->claimed = 0;
> +}
> +
> +static int spi_hid_ll_open(struct hid_device *hid)
> +{
> + struct spi_device *spi = hid->driver_data;
> + struct spi_hid *shid = spi_get_drvdata(spi);
> + struct device *dev = &spi->dev;
> + u8 prev_state = shid->power_state;
> +
> + if (shid->refresh_in_progress)
> + return 0;
> +
> + spi_hid_resume(shid);
> +
> + dev_err(dev, "%s: %s -> %s\n", __func__,
> + spi_hid_power_mode_string(prev_state),
> + spi_hid_power_mode_string(shid->power_state));
> +
> + return 0;
> +}
> +
> +static void spi_hid_ll_close(struct hid_device *hid)
> +{
> + struct spi_device *spi = hid->driver_data;
> + struct spi_hid *shid = spi_get_drvdata(spi);
> + struct device *dev = &spi->dev;
> + u8 prev_state = shid->power_state;
> +
> + if (shid->refresh_in_progress)
> + return;
> +
> + spi_hid_suspend(shid);
> +
> + shid->attempts = 0;
> +
> + dev_err(dev, "%s: %s -> %s\n", __func__,
> + spi_hid_power_mode_string(prev_state),
> + spi_hid_power_mode_string(shid->power_state));
Seems like a debug message that needs to be dropped or at least used in dev_dbg
> +}
> +
> +static int spi_hid_ll_power(struct hid_device *hid, int level)
> +{
> + struct spi_device *spi = hid->driver_data;
> + struct spi_hid *shid = spi_get_drvdata(spi);
> + int ret = 0;
> +
> + mutex_lock(&shid->lock);
> + if (!shid->hid)
> + ret = -ENODEV;
> + mutex_unlock(&shid->lock);
> +
> + return ret;
> +}
> +
> +static int spi_hid_ll_parse(struct hid_device *hid)
> +{
> + struct spi_device *spi = hid->driver_data;
> + struct spi_hid *shid = spi_get_drvdata(spi);
> + struct device *dev = &spi->dev;
> + int ret, len;
> +
> + mutex_lock(&shid->lock);
> +
> + len = spi_hid_report_descriptor_request(shid);
> + if (len < 0) {
> + dev_err(dev, "Report descriptor request failed, %d\n", len);
> + ret = len;
> + goto out;
> + }
> +
> + /*
> + * FIXME: below call returning 0 doesn't mean that the report descriptor
> + * is good. We might be caching a crc32 of a corrupted r. d. or who
> + * knows what the FW sent. Need to have a feedback loop about r. d.
> + * being ok and only then cache it.
Shouldn't you check for the CRC before submitting to hid_parse_report then?
> + */
> + ret = hid_parse_report(hid, (__u8 *)shid->response.content, len);
> + if (ret)
> + dev_err(dev, "failed parsing report: %d\n", ret);
> + else
> + shid->report_descriptor_crc32 = crc32_le(0,
> + (unsigned char const *)shid->response.content,
> + len);
> +
> +out:
> + mutex_unlock(&shid->lock);
> +
> + return ret;
> +}
> +
> +static int spi_hid_ll_raw_request(struct hid_device *hid,
> + unsigned char reportnum, __u8 *buf, size_t len,
> + unsigned char rtype, int reqtype)
> +{
> + struct spi_device *spi = hid->driver_data;
> + struct spi_hid *shid = spi_get_drvdata(spi);
> + struct device *dev = &spi->dev;
> + int ret;
> +
> + if (!shid->ready) {
> + dev_err(&shid->spi->dev, "%s called in unready state\n",
> + __func__);
> + return -ENODEV;
> + }
> +
> + mutex_lock(&shid->lock);
> +
> + switch (reqtype) {
> + case HID_REQ_SET_REPORT:
> + if (buf[0] != reportnum) {
> + dev_err(dev, "report id mismatch\n");
> + ret = -EINVAL;
> + break;
> + }
> +
> + ret = spi_hid_set_request(shid, &buf[1], len - 1,
> + reportnum);
> + if (ret) {
> + dev_err(dev, "failed to set report\n");
> + break;
> + }
> +
> + ret = len;
> + break;
> + case HID_REQ_GET_REPORT:
> + ret = spi_hid_get_request(shid, reportnum);
> + if (ret) {
> + dev_err(dev, "failed to get report\n");
> + break;
> + }
> +
> + ret = min_t(size_t, len,
> + shid->response.body[1] | (shid->response.body[2] << 8));
> + memcpy(buf, &shid->response.content, ret);
> + break;
> + default:
> + dev_err(dev, "invalid request type\n");
> + ret = -EIO;
> + }
> +
> + mutex_unlock(&shid->lock);
> +
> + return ret;
> +}
> +
> +static int spi_hid_ll_output_report(struct hid_device *hid,
> + __u8 *buf, size_t len)
> +{
> + int ret;
> + struct spi_device *spi = hid->driver_data;
> + struct spi_hid *shid = spi_get_drvdata(spi);
> + struct device *dev = &spi->dev;
> + struct spi_hid_output_report report = {
> + .report_type = SPI_HID_OUTPUT_REPORT_TYPE_HID_OUTPUT_REPORT,
> + .content_length = len - 1,
> + .content_id = buf[0],
> + .content = &buf[1],
> + };
> +
> + mutex_lock(&shid->lock);
> + if (!shid->ready) {
> + dev_err(dev, "%s called in unready state\n", __func__);
> + ret = -ENODEV;
> + goto out;
> + }
> +
> + if (shid->desc.no_output_report_ack)
> + ret = spi_hid_send_output_report(shid, &report);
> + else
> + ret = spi_hid_sync_request(shid, &report);
> +
> + if (ret)
> + dev_err(dev, "failed to send output report\n");
> +
> +out:
> + mutex_unlock(&shid->lock);
> +
> + if (ret > 0)
> + return -ret;
> +
> + if (ret < 0)
> + return ret;
> +
> + return len;
> +}
> +
> +void spi_hid_ll_reset(struct hid_device *hid)
> +{
> + struct spi_device *spi = hid->driver_data;
> + struct device *dev = &spi->dev;
> + struct spi_hid *shid = spi_get_drvdata(spi);
> +
> + dev_err(dev, "%s()\n", __func__);
> + spi_hid_error_handler(shid);
> +}
> +
> +static struct hid_ll_driver spi_hid_ll_driver = {
> + .start = spi_hid_ll_start,
> + .stop = spi_hid_ll_stop,
> + .open = spi_hid_ll_open,
> + .close = spi_hid_ll_close,
> + .power = spi_hid_ll_power,
> + .parse = spi_hid_ll_parse,
> + .output_report = spi_hid_ll_output_report,
> + .raw_request = spi_hid_ll_raw_request,
> + .reset = spi_hid_ll_reset
> +};
> +
> +static const struct of_device_id spi_hid_of_match[] = {
> + { .compatible = "hid-over-spi" },
I don't think there is a matching OF Documentation attached to this
patch series. Please add one in a separate patch and CC the proper
maintainers and list.
> + {},
> +};
> +MODULE_DEVICE_TABLE(of, spi_hid_of_match);
> +
> +static ssize_t ready_show(struct device *dev,
> + struct device_attribute *attr, char *buf)
> +{
> + struct spi_hid *shid = dev_get_drvdata(dev);
> +
> + return snprintf(buf, PAGE_SIZE, "%s\n",
> + shid->ready ? "ready" : "not ready");
> +}
> +static DEVICE_ATTR_RO(ready);
> +
> +static const struct attribute *const spi_hid_attributes[] = {
> + &dev_attr_ready.attr,
> + NULL /* Terminator */
> +};
> +
> +static int spi_hid_probe(struct spi_device *spi)
> +{
> + struct device *dev = &spi->dev;
> + struct spi_hid *shid;
> + unsigned long irqflags;
> + int ret;
> + u32 val;
> +
> + if (spi->irq <= 0) {
> + dev_err(dev, "Missing IRQ\n");
> + ret = spi->irq ?: -EINVAL;
> + goto err0;
> + }
> +
> + shid = devm_kzalloc(dev, sizeof(struct spi_hid), GFP_KERNEL);
> + if (!shid) {
> + ret = -ENOMEM;
> + goto err0;
> + }
> +
> + shid->spi = spi;
> + shid->power_state = SPI_HID_POWER_MODE_ON;
> + spi_set_drvdata(spi, shid);
> +
> + ret = sysfs_create_files(&dev->kobj, spi_hid_attributes);
> + if (ret) {
> + dev_err(dev, "Unable to create sysfs attributes\n");
> + goto err0;
> + }
> +
> + ret = device_property_read_u32(dev, "input-report-header-address",
> + &val);
Please look at the latest version of i2c-hid in Linus tree. We went
through a separation of the core of i2c-hid (the part the spec is
about), and the ACPI/OF bindings. It would be nice if we could have
that from day one on spi-hid too.
This allows some advantages:
- we completely separate the ACPI calls from the OF calls, making the
drivers easier to read
- i2c-hid-of.c can be in charge of the various regulators and the ACPI
version can just ignores all of that
- we can overload i2c-hid-of.c with some device specifics if we have
some device that need special parameters (like extra sleep times or
specific reset lines).
Note that I do not request you to work on the ACPI part, but just to
have a split in OF/core so we can later on easily add ACPI.
> + if (ret) {
> + dev_err(dev, "Input report header address not provided\n");
> + ret = -ENODEV;
> + goto err1;
> + }
> + shid->conf.input_report_header_address = val;
> +
> + ret = device_property_read_u32(dev, "input-report-body-address", &val);
> + if (ret) {
> + dev_err(dev, "Input report body address not provided\n");
> + ret = -ENODEV;
> + goto err1;
> + }
> + shid->conf.input_report_body_address = val;
> +
> + ret = device_property_read_u32(dev, "output-report-address", &val);
> + if (ret) {
> + dev_err(dev, "Output report address not provided\n");
> + ret = -ENODEV;
> + goto err1;
> + }
> + shid->conf.output_report_address = val;
> +
> + ret = device_property_read_u32(dev, "read-opcode", &val);
> + if (ret) {
> + dev_err(dev, "Read opcode not provided\n");
> + ret = -ENODEV;
> + goto err1;
> + }
> + shid->conf.read_opcode = val;
> +
> + ret = device_property_read_u32(dev, "write-opcode", &val);
> + if (ret) {
> + dev_err(dev, "Write opcode not provided\n");
> + ret = -ENODEV;
> + goto err1;
> + }
> + shid->conf.write_opcode = val;
> +
> + /* FIXME: not reading flags from DT, multi-SPI modes not supported */
> +
> + /* Using now populated conf let's pre-calculate the read approvals */
> + spi_hid_populate_read_approvals(&shid->conf, shid->read_approval_header,
> + shid->read_approval_body);
> +
> + mutex_init(&shid->lock);
> + init_completion(&shid->output_done);
> +
> + shid->supply = devm_regulator_get(dev, "vdd");
> + if (IS_ERR(shid->supply)) {
> + if (PTR_ERR(shid->supply) != -EPROBE_DEFER)
> + dev_err(dev, "Failed to get regulator: %ld\n",
> + PTR_ERR(shid->supply));
> + ret = PTR_ERR(shid->supply);
> + goto err1;
> + }
> +
> + spin_lock_init(&shid->input_lock);
> + INIT_WORK(&shid->reset_work, spi_hid_reset_work);
> + INIT_WORK(&shid->create_device_work, spi_hid_create_device_work);
> + INIT_WORK(&shid->refresh_device_work, spi_hid_refresh_device_work);
> + INIT_WORK(&shid->error_work, spi_hid_error_work);
> + INIT_WORK(&shid->notify_device_driver_work,
> + spi_hid_notify_device_driver_work);
> +
> + /*
> + * At the end of probe we initialize the device:
> + * 0) Default pinctrl in DT: assert reset, bias the interrupt line
> + * 1) sleep 100ms
> + * 2) request IRQ
> + * 3) power up the device
> + * 4) sleep 5ms
> + * 5) deassert reset (high)
> + * 6) sleep 5ms
> + */
> +
> + shid->reset_gpio = gpiod_get(dev, "ms_g6_reset_gpio", GPIOD_OUT_LOW);
> + if (IS_ERR(shid->reset_gpio)) {
> + dev_err(dev, "%s: error getting GPIO\n", __func__);
> + goto err1;
> + }
> +
> + /* FIXME: timeout values should come from DT */
> + msleep(100);
> +
> + irqflags = irq_get_trigger_type(spi->irq) | IRQF_ONESHOT;
> + ret = request_irq(spi->irq, spi_hid_dev_irq, irqflags,
> + dev_name(&spi->dev), shid);
> + if (ret)
> + goto err1;
> +
> + ret = spi_hid_power_up(shid);
> + if (ret) {
> + dev_err(dev, "%s: could not power up\n", __func__);
> + goto err1;
> + }
> +
> + gpiod_set_value(shid->reset_gpio, 0);
> +
> + /* FIXME: timeout values should come from DT */
> + usleep_range(5000, 6000);
> +
> + dev_err(dev, "%s: d3 -> %s\n", __func__,
> + spi_hid_power_mode_string(shid->power_state));
> +
> + return 0;
> +
> +err1:
> + sysfs_remove_files(&dev->kobj, spi_hid_attributes);
> +
> +err0:
> + return ret;
> +}
> +
> +static int spi_hid_remove(struct spi_device *spi)
> +{
> + struct spi_hid *shid = spi_get_drvdata(spi);
> + struct device *dev = &spi->dev;
> +
> + gpiod_set_value(shid->reset_gpio, 1);
> + gpiod_put(shid->reset_gpio);
> + spi_hid_power_down(shid);
> + free_irq(spi->irq, shid);
> + sysfs_remove_files(&dev->kobj, spi_hid_attributes);
> + spi_hid_stop_hid(shid);
> +
> + return 0;
> +}
> +
> +static const struct spi_device_id spi_hid_id_table[] = {
> + { "hid", 0 },
> + { "hid-over-spi", 0 },
> + { },
> +};
> +MODULE_DEVICE_TABLE(spi, spi_hid_id_table);
> +
> +static struct spi_driver spi_hid_driver = {
> + .driver = {
> + .name = "spi_hid",
> + .owner = THIS_MODULE,
> + .of_match_table = of_match_ptr(spi_hid_of_match),
We probbaly need:
.probe_type = PROBE_PREFER_ASYNCHRONOUS,
and some .pm functions
> + },
> + .probe = spi_hid_probe,
> + .remove = spi_hid_remove,
i2c-hid also defines a .shutdown callback. Maybe we need one too?
> + .id_table = spi_hid_id_table,
> +};
> +
> +module_spi_driver(spi_hid_driver);
> +
> +MODULE_DESCRIPTION("HID over SPI transport driver");
> +MODULE_AUTHOR("Dmitry Antipov <dmanti@xxxxxxxxxxxxx>");
> +MODULE_LICENSE("GPL");
> diff --git a/drivers/hid/spi-hid/spi-hid-core.h b/drivers/hid/spi-hid/spi-hid-core.h
> new file mode 100644
> index 000000000000..bb154162ff3e
> --- /dev/null
> +++ b/drivers/hid/spi-hid/spi-hid-core.h
> @@ -0,0 +1,201 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * spi-hid-core.h
> + *
> + * Copyright (c) 2021 Microsoft Corporation
> + *
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms of the GNU General Public License version 2 as published by
> + * the Free Software Foundation.
> + */
> +
> +#ifndef SPI_HID_CORE_H
> +#define SPI_HID_CORE_H
> +
> +#include <linux/completion.h>
> +#include <linux/kernel.h>
> +#include <linux/spi/spi.h>
> +#include <linux/spinlock.h>
> +#include <linux/types.h>
> +
> +/* Protocol constants */
> +#define SPI_HID_READ_APPROVAL_CONSTANT 0xff
> +#define SPI_HID_INPUT_HEADER_SYNC_BYTE 0x5a
> +#define SPI_HID_INPUT_HEADER_VERSION 0x03
> +#define SPI_HID_SUPPORTED_VERSION 0x0300
> +
> +/* Protocol message size constants */
> +#define SPI_HID_READ_APPROVAL_LEN 5
> +#define SPI_HID_INPUT_HEADER_LEN 4
> +#define SPI_HID_INPUT_BODY_LEN 4
> +#define SPI_HID_OUTPUT_HEADER_LEN 8
> +#define SPI_HID_DEVICE_DESCRIPTOR_LENGTH 24
> +
> +/* Protocol message type constants */
> +#define SPI_HID_INPUT_REPORT_TYPE_DATA 0x01
> +#define SPI_HID_INPUT_REPORT_TYPE_RESET_RESP 0x03
> +#define SPI_HID_INPUT_REPORT_TYPE_COMMAND_RESP 0x04
> +#define SPI_HID_INPUT_REPORT_TYPE_GET_FEATURE_RESP 0x05
> +#define SPI_HID_INPUT_REPORT_TYPE_DEVICE_DESC 0x07
> +#define SPI_HID_INPUT_REPORT_TYPE_REPORT_DESC 0x08
> +#define SPI_HID_INPUT_REPORT_TYPE_SET_FEATURE_RESP 0x09
> +#define SPI_HID_INPUT_REPORT_TYPE_SET_OUTPUT_REPORT_RESP 0x0a
> +#define SPI_HID_INPUT_REPORT_TYPE_GET_INPUT_REPORT_RESP 0x0b
> +
> +#define SPI_HID_OUTPUT_REPORT_TYPE_DEVICE_DESC_REQUEST 0x01
> +#define SPI_HID_OUTPUT_REPORT_TYPE_REPORT_DESC_REQUEST 0x02
> +#define SPI_HID_OUTPUT_REPORT_TYPE_HID_SET_FEATURE 0x03
> +#define SPI_HID_OUTPUT_REPORT_TYPE_HID_GET_FEATURE 0x04
> +#define SPI_HID_OUTPUT_REPORT_TYPE_HID_OUTPUT_REPORT 0x05
> +#define SPI_HID_OUTPUT_REPORT_TYPE_INPUT_REPORT_REQUEST 0x06
> +#define SPI_HID_OUTPUT_REPORT_TYPE_COMMAND 0x07
> +
> +#define SPI_HID_OUTPUT_REPORT_CONTENT_ID_DESC_REQUEST 0x00
> +
> +/* Power mode constants */
> +#define SPI_HID_POWER_MODE_ON 0x01
> +#define SPI_HID_POWER_MODE_SLEEP 0x02
> +#define SPI_HID_POWER_MODE_OFF 0x03
> +#define SPI_HID_POWER_MODE_WAKING_SLEEP 0x04
> +
> +/* Config structure is filled based on data from Device Tree */
> +struct spi_hid_host_config {
> + u32 input_report_header_address;
> + u32 input_report_body_address;
> + u32 output_report_address;
> + u8 read_opcode;
> + u8 write_opcode;
> +};
> +
> +/* Raw input buffer with data from the bus */
> +struct spi_hid_input_buf {
> + __u8 header[SPI_HID_INPUT_HEADER_LEN];
> + __u8 body[SPI_HID_INPUT_BODY_LEN];
> + u8 content[SZ_8K];
> +};
> +
> +/* Processed data from input report header */
> +struct spi_hid_input_header {
> + u8 version;
> + u16 report_length;
> + u8 last_fragment_flag;
> + u8 sync_const;
> +};
> +
> +/* Processed data from input report body, excluding the content */
> +struct spi_hid_input_body {
> + u8 report_type;
> + u16 content_length;
> + u8 content_id;
> +};
> +
> +/* Processed data from an input report */
> +struct spi_hid_input_report {
> + u8 report_type;
> + u16 content_length;
> + u8 content_id;
> + u8 *content;
> +};
> +
> +/* Raw output report buffer to be put on the bus */
> +struct spi_hid_output_buf {
> + __u8 header[SPI_HID_OUTPUT_HEADER_LEN];
> + u8 content[SZ_8K];
> +};
> +
> +/* Data necessary to send an output report */
> +struct spi_hid_output_report {
> + u8 report_type;
> + u16 content_length;
> + u8 content_id;
> + u8 *content;
> +};
> +
> +/* Raw content in device descriptor */
> +struct spi_hid_device_desc_raw {
> + __le16 wDeviceDescLength;
> + __le16 bcdVersion;
> + __le16 wReportDescLength;
> + __le16 wMaxInputLength;
> + __le16 wMaxOutputLength;
> + __le16 wMaxFragmentLength;
> + __le16 wVendorID;
> + __le16 wProductID;
> + __le16 wVersionID;
> + __le16 wFlags;
> + __u8 reserved[4];
> +} __packed;
> +
> +/* Processed data from a device descriptor */
> +struct spi_hid_device_descriptor {
> + u16 hid_version;
> + u16 report_descriptor_length;
> + u16 max_input_length;
> + u16 max_output_length;
> + u16 max_fragment_length;
> + u16 vendor_id;
> + u16 product_id;
> + u16 version_id;
> + u8 no_output_report_ack;
> +};
> +
> +/* Driver context */
> +struct spi_hid {
> + struct spi_device *spi;
> + struct hid_device *hid;
> +
> + struct spi_transfer input_transfer[2];
> + struct spi_transfer output_transfer;
> + struct spi_message input_message;
> + struct spi_message output_message;
> +
> + struct spi_hid_host_config conf;
> + struct spi_hid_device_descriptor desc;
> + struct spi_hid_output_buf output;
> + struct spi_hid_input_buf input;
> + struct spi_hid_input_buf response;
> +
> + spinlock_t input_lock;
> +
> + u32 input_transfer_pending;
> +
> + u8 power_state;
> +
> + u8 attempts;
> +
> + /*
> + * ready flag indicates that the FW is ready to accept commands and
> + * requests. The FW becomes ready after sending the report descriptor.
> + */
> + bool ready;
> + /*
> + * refresh_in_progress is set to true while the refresh_device worker
> + * thread is destroying and recreating the hidraw device. When this flag
> + * is set to true, the ll_close and ll_open functions will not cause
> + * power state changes
> + */
> + bool refresh_in_progress;
> +
> + struct regulator *supply;
> + struct work_struct reset_work;
> + struct work_struct create_device_work;
> + struct work_struct refresh_device_work;
> + struct work_struct error_work;
> + struct work_struct notify_device_driver_work;
> +
> + int notify_device_driver_error_type;
> + int notify_device_driver_error_code;
> + bool notify_device_driver_handled;
> +
> + struct mutex lock;
> + struct completion output_done;
> +
> + __u8 read_approval_header[SPI_HID_READ_APPROVAL_LEN];
> + __u8 read_approval_body[SPI_HID_READ_APPROVAL_LEN];
> +
> + u32 report_descriptor_crc32;
> +
> + struct gpio_desc *reset_gpio;
> +};
As a general rule of thumb, we don't split those definitions out of
the .c file, if they are not used outside of it.
OTOH, you will need a spi-hid.h file for the OF/ACPI split so meh...
> +
> +#endif
> diff --git a/drivers/hid/spi-hid/spi-hid_trace.h b/drivers/hid/spi-hid/spi-hid_trace.h
> new file mode 100644
> index 000000000000..60264bac0dc5
> --- /dev/null
> +++ b/drivers/hid/spi-hid/spi-hid_trace.h
> @@ -0,0 +1,197 @@
> +/* SPDX-License-Identifier: GPL-2.0 */
> +/*
> + * spi-hid_trace.h
> + *
> + * Copyright (c) 2021 Microsoft Corporation
> + *
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms of the GNU General Public License version 2 as published by
> + * the Free Software Foundation.
I think you can drop that based on the SPDX header
Besides that. I assume that those trace points are used with ftrace?
If so, that's a very nice addition :)
> + */
> +
> +#undef TRACE_SYSTEM
> +#define TRACE_SYSTEM spi_hid
> +
> +#if !defined(_SPI_HID_TRACE_H) || defined(TRACE_HEADER_MULTI_READ)
> +#define _SPI_HID_TRACE_H
> +
> +#include <linux/types.h>
> +#include <linux/tracepoint.h>
> +#include "spi-hid-core.h"
> +
> +DECLARE_EVENT_CLASS(spi_hid_transfer,
> + TP_PROTO(struct spi_hid *shid, const void *tx_buf, int tx_len,
> + const void *rx_buf, u16 rx_len, int ret),
> +
> + TP_ARGS(shid, tx_buf, tx_len, rx_buf, rx_len, ret),
> +
> + TP_STRUCT__entry(
> + __field(int, bus_num)
> + __field(int, chip_select)
> + __field(int, len)
> + __field(int, ret)
> + __dynamic_array(u8, rx_buf, rx_len)
> + __dynamic_array(u8, tx_buf, tx_len)
> + ),
> +
> + TP_fast_assign(
> + __entry->bus_num = shid->spi->controller->bus_num;
> + __entry->chip_select = shid->spi->chip_select;
> + __entry->len = rx_len + tx_len;
> + __entry->ret = ret;
> +
> + memcpy(__get_dynamic_array(tx_buf), tx_buf, tx_len);
> + memcpy(__get_dynamic_array(rx_buf), rx_buf, rx_len);
> + ),
> +
> + TP_printk("spi%d.%d: len=%d tx=[%*phD] rx=[%*phD] --> %d",
> + __entry->bus_num, __entry->chip_select, __entry->len,
> + __get_dynamic_array_len(tx_buf), __get_dynamic_array(tx_buf),
> + __get_dynamic_array_len(rx_buf), __get_dynamic_array(rx_buf),
> + __entry->ret)
> +);
> +
> +DEFINE_EVENT(spi_hid_transfer, spi_hid_input_async,
> + TP_PROTO(struct spi_hid *shid, const void *tx_buf, int tx_len,
> + const void *rx_buf, u16 rx_len, int ret),
> + TP_ARGS(shid, tx_buf, tx_len, rx_buf, rx_len, ret)
> +);
> +
> +DEFINE_EVENT(spi_hid_transfer, spi_hid_input_header_complete,
> + TP_PROTO(struct spi_hid *shid, const void *tx_buf, int tx_len,
> + const void *rx_buf, u16 rx_len, int ret),
> + TP_ARGS(shid, tx_buf, tx_len, rx_buf, rx_len, ret)
> +);
> +
> +DEFINE_EVENT(spi_hid_transfer, spi_hid_input_body_complete,
> + TP_PROTO(struct spi_hid *shid, const void *tx_buf, int tx_len,
> + const void *rx_buf, u16 rx_len, int ret),
> + TP_ARGS(shid, tx_buf, tx_len, rx_buf, rx_len, ret)
> +);
> +
> +DEFINE_EVENT(spi_hid_transfer, spi_hid_output_begin,
> + TP_PROTO(struct spi_hid *shid, const void *tx_buf, int tx_len,
> + const void *rx_buf, u16 rx_len, int ret),
> + TP_ARGS(shid, tx_buf, tx_len, rx_buf, rx_len, ret)
> +);
> +
> +DEFINE_EVENT(spi_hid_transfer, spi_hid_output_end,
> + TP_PROTO(struct spi_hid *shid, const void *tx_buf, int tx_len,
> + const void *rx_buf, u16 rx_len, int ret),
> + TP_ARGS(shid, tx_buf, tx_len, rx_buf, rx_len, ret)
> +);
> +
> +DECLARE_EVENT_CLASS(spi_hid_irq,
> + TP_PROTO(struct spi_hid *shid, int irq),
> +
> + TP_ARGS(shid, irq),
> +
> + TP_STRUCT__entry(
> + __field(int, bus_num)
> + __field(int, chip_select)
> + __field(int, irq)
> + ),
> +
> + TP_fast_assign(
> + __entry->bus_num = shid->spi->controller->bus_num;
> + __entry->chip_select = shid->spi->chip_select;
> + __entry->irq = irq;
> + ),
> +
> + TP_printk("spi%d.%d: IRQ %d",
> + __entry->bus_num, __entry->chip_select, __entry->irq)
> +);
> +
> +DEFINE_EVENT(spi_hid_irq, spi_hid_dev_irq,
> + TP_PROTO(struct spi_hid *shid, int irq),
> + TP_ARGS(shid, irq)
> +);
> +
> +DECLARE_EVENT_CLASS(spi_hid,
> + TP_PROTO(struct spi_hid *shid),
> +
> + TP_ARGS(shid),
> +
> + TP_STRUCT__entry(
> + __field(int, bus_num)
> + __field(int, chip_select)
> + __field(int, power_state)
> + __field(u32, input_transfer_pending)
> + __field(bool, ready)
> +
> + __field(int, vendor_id)
> + __field(int, product_id)
> + __field(int, max_input_length)
> + __field(int, max_output_length)
> + __field(u16, hid_version)
> + __field(u16, report_descriptor_length)
> + __field(u16, version_id)
> + ),
> +
> + TP_fast_assign(
> + __entry->bus_num = shid->spi->controller->bus_num;
> + __entry->chip_select = shid->spi->chip_select;
> + __entry->power_state = shid->power_state;
> + __entry->input_transfer_pending = shid->input_transfer_pending;
> + __entry->ready = shid->ready;
> +
> + __entry->vendor_id = shid->desc.vendor_id;
> + __entry->product_id = shid->desc.product_id;
> + __entry->max_input_length = shid->desc.max_input_length;
> + __entry->max_output_length = shid->desc.max_output_length;
> + __entry->hid_version = shid->desc.hid_version;
> + __entry->report_descriptor_length =
> + shid->desc.report_descriptor_length;
> + __entry->version_id = shid->desc.version_id;
> + ),
> +
> + TP_printk("spi%d.%d: (%04x:%04x v%d) HID v%d.%d state i:%d p:%d len i:%d o:%d r:%d flags %c:%d",
> + __entry->bus_num, __entry->chip_select, __entry->vendor_id,
> + __entry->product_id, __entry->version_id,
> + __entry->hid_version >> 8, __entry->hid_version & 0xff,
> + __entry->power_state, __entry->max_input_length,
> + __entry->max_output_length, __entry->report_descriptor_length,
> + __entry->ready ? 'R' : 'r', __entry->input_transfer_pending)
> +);
> +
> +DEFINE_EVENT(spi_hid, spi_hid_header_transfer,
> + TP_PROTO(struct spi_hid *shid),
> + TP_ARGS(shid)
> +);
> +
> +DEFINE_EVENT(spi_hid, spi_hid_process_input_report,
> + TP_PROTO(struct spi_hid *shid),
> + TP_ARGS(shid)
> +);
> +
> +DEFINE_EVENT(spi_hid, spi_hid_input_report_handler,
> + TP_PROTO(struct spi_hid *shid),
> + TP_ARGS(shid)
> +);
> +
> +DEFINE_EVENT(spi_hid, spi_hid_reset_work,
> + TP_PROTO(struct spi_hid *shid),
> + TP_ARGS(shid)
> +);
> +
> +DEFINE_EVENT(spi_hid, spi_hid_create_device_work,
> + TP_PROTO(struct spi_hid *shid),
> + TP_ARGS(shid)
> +);
> +
> +DEFINE_EVENT(spi_hid, spi_hid_refresh_device_work,
> + TP_PROTO(struct spi_hid *shid),
> + TP_ARGS(shid)
> +);
> +
> +DEFINE_EVENT(spi_hid, spi_hid_response_handler,
> + TP_PROTO(struct spi_hid *shid),
> + TP_ARGS(shid)
> +);
> +
> +#endif /* _SPI_HID_TRACE_H */
> +
> +#undef TRACE_INCLUDE_PATH
> +#define TRACE_INCLUDE_PATH .
> +#define TRACE_INCLUDE_FILE spi-hid_trace
> +#include <trace/define_trace.h>
> diff --git a/drivers/hid/spi-hid/trace.c b/drivers/hid/spi-hid/trace.c
> new file mode 100644
> index 000000000000..7be35c8405df
> --- /dev/null
> +++ b/drivers/hid/spi-hid/trace.c
> @@ -0,0 +1,11 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/**
> + * trace.c - SPI HID Trace Support
> + *
> + * Copyright (C) 2021 Microsoft Corporation
> + *
> + * Author: Felipe Balbi <felipe.balbi@xxxxxxxxxxxxx>
> + */
> +
> +#define CREATE_TRACE_POINTS
> +#include "spi-hid_trace.h"
> --
> 2.25.1
>
Cheers,
Benjamin
Re: [PATCH v1 5/5] HID: add spi-hid, transport driver for HID over SPI bus
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
- Subject: Re: [PATCH v1 5/5] HID: add spi-hid, transport driver for HID over SPI bus
- From: Benjamin Tissoires <benjamin.tissoires@xxxxxxxxxx>
- Date: Mon, 3 Jan 2022 18:26:07 +0100
- Cc: Jiri Kosina <jikos@xxxxxxxxxx>, "open list:HID CORE LAYER" <linux-input@xxxxxxxxxxxxxxx>, Felipe Balbi <balbi@xxxxxxxxxx>, Dmitry Antipov <dmanti@xxxxxxxxxxxxx>, Mark Brown <broonie@xxxxxxxxxx>, linux-spi@xxxxxxxxxxxxxxx
- In-reply-to: <20211229231141.303919-6-dmanti@microsoft.com>
- References: <20211229231141.303919-1-dmanti@microsoft.com> <20211229231141.303919-6-dmanti@microsoft.com>
- Follow-Ups:
- Prev by Date: Re: [PATCH 2/2] spi: dt-bindings: samsung: convert to dtschema
- Next by Date: [PATCH v9 00/13] External ECC engines & Macronix support
- Previous by thread: [PATCH v2 1/2] spi: qcom: geni: set the error code for gpi transfer
- Next by thread: RE: [EXTERNAL] Re: [PATCH v1 5/5] HID: add spi-hid, transport driver for HID over SPI bus
- Index(es):
 |