[PATCH v2 1/2] spi: cadence-quadspi: Disable Auto-HW polling

[Apurva Nandan <a-nandan@xxxxxx>]

cadence-quadspi has a builtin Auto-HW polling funtionality using which
it keep tracks of completion of write operations. When Auto-HW polling
is enabled, it automatically initiates status register read operation,
until the flash clears its busy bit.

cadence-quadspi controller doesn't allow an address phase when
auto-polling the busy bit on the status register. Unlike SPI NOR
flashes, SPI NAND flashes do require the address of status register
when polling the busy bit using the read register operation. As
Auto-HW polling is enabled by default, cadence-quadspi returns a
timeout for every write operation after an indefinite amount of
polling on SPI NAND flashes.

Disable Auto-HW polling completely as the spi-nor core, spinand core,
etc. take care of polling the busy bit on their own.

Signed-off-by: Apurva Nandan <a-nandan@xxxxxx>
Link: https://lore.kernel.org/r/20210713125743.1540-2-a-nandan@xxxxxx
Signed-off-by: Mark Brown <broonie@xxxxxxxxxx>
---
 This patch has already been applied to
 https://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi.git for-next
 [1/2] spi: cadence-quadspi: Disable Auto-HW polling
       commit: 9cb2ff11171264d10be7ea9e31d9ee5d49ba84a5
 Reposting it for sake of completeness of the v2 series.

 drivers/spi/spi-cadence-quadspi.c | 27 ++++++++++++++-------------
 1 file changed, 14 insertions(+), 13 deletions(-)

diff --git a/drivers/spi/spi-cadence-quadspi.c b/drivers/spi/spi-cadence-quadspi.c
index d62d69dd72b9..a2de23516553 100644
--- a/drivers/spi/spi-cadence-quadspi.c
+++ b/drivers/spi/spi-cadence-quadspi.c
@@ -800,19 +800,20 @@ static int cqspi_write_setup(struct cqspi_flash_pdata *f_pdata,
 	reg = cqspi_calc_rdreg(f_pdata);
 	writel(reg, reg_base + CQSPI_REG_RD_INSTR);
 
-	if (f_pdata->dtr) {
-		/*
-		 * Some flashes like the cypress Semper flash expect a 4-byte
-		 * dummy address with the Read SR command in DTR mode, but this
-		 * controller does not support sending address with the Read SR
-		 * command. So, disable write completion polling on the
-		 * controller's side. spi-nor will take care of polling the
-		 * status register.
-		 */
-		reg = readl(reg_base + CQSPI_REG_WR_COMPLETION_CTRL);
-		reg |= CQSPI_REG_WR_DISABLE_AUTO_POLL;
-		writel(reg, reg_base + CQSPI_REG_WR_COMPLETION_CTRL);
-	}
+	/*
+	 * SPI NAND flashes require the address of the status register to be
+	 * passed in the Read SR command. Also, some SPI NOR flashes like the
+	 * cypress Semper flash expect a 4-byte dummy address in the Read SR
+	 * command in DTR mode.
+	 *
+	 * But this controller does not support address phase in the Read SR
+	 * command when doing auto-HW polling. So, disable write completion
+	 * polling on the controller's side. spinand and spi-nor will take
+	 * care of polling the status register.
+	 */
+	reg = readl(reg_base + CQSPI_REG_WR_COMPLETION_CTRL);
+	reg |= CQSPI_REG_WR_DISABLE_AUTO_POLL;
+	writel(reg, reg_base + CQSPI_REG_WR_COMPLETION_CTRL);
 
 	reg = readl(reg_base + CQSPI_REG_SIZE);
 	reg &= ~CQSPI_REG_SIZE_ADDRESS_MASK;
-- 
2.17.1