Hi Dinghao,
On 4/15/21 3:17 PM, Dinghao Liu wrote:
There is a PM usage counter decrement after zynqmp_qspi_init_hw()
without any refcount increment, which leads to refcount leak.Add
a refcount increment to balance the refcount. Also set
auto_runtime_pm to resume suspended spi controller.
Fixes: 9e3a000362aec ("spi: zynqmp: Add pm runtime support")
Signed-off-by: Dinghao Liu <dinghao.liu@xxxxxxxxxx>
---
Changelog:
v2: - Add a refcount increment to fix refcout leak instead of the
refcount decrement on error.
Set ctlr->auto_runtime_pm = true.
v3: - Add fix tag.
Add a return value check against pm_runtime_get_sync().
Move pm_runtime_{mark_last_busy & put_autosuspend} to the
end of current function.
---
drivers/spi/spi-zynqmp-gqspi.c | 12 ++++++++++--
1 file changed, 10 insertions(+), 2 deletions(-)
diff --git a/drivers/spi/spi-zynqmp-gqspi.c b/drivers/spi/spi-zynqmp-gqspi.c
index c8fa6ee18ae7..781ef3fc76e2 100644
--- a/drivers/spi/spi-zynqmp-gqspi.c
+++ b/drivers/spi/spi-zynqmp-gqspi.c
@@ -1160,11 +1160,14 @@ static int zynqmp_qspi_probe(struct platform_device *pdev)
pm_runtime_set_autosuspend_delay(&pdev->dev, SPI_AUTOSUSPEND_TIMEOUT);
pm_runtime_set_active(&pdev->dev);
pm_runtime_enable(&pdev->dev);
+
+ ret = pm_runtime_get_sync(&pdev->dev);
+ if (ret < 0)
+ goto clk_dis_all;
Would you please add some error info output here? Just like:
+ if (ret < 0) {
+ dev_err(&pdev->dev, "failed to pm_runtime_get_sync:
%d\n", ret);
+ goto clk_dis_all;
+ }
Because sometimes it is very helpful to analyse probe failure.
Thanks,
Quanyang
+
/* QSPI controller initializations */
zynqmp_qspi_init_hw(xqspi);
- pm_runtime_mark_last_busy(&pdev->dev);
- pm_runtime_put_autosuspend(&pdev->dev);
xqspi->irq = platform_get_irq(pdev, 0);
if (xqspi->irq <= 0) {
ret = -ENXIO;
@@ -1187,6 +1190,7 @@ static int zynqmp_qspi_probe(struct platform_device *pdev)
ctlr->mode_bits = SPI_CPOL | SPI_CPHA | SPI_RX_DUAL | SPI_RX_QUAD |
SPI_TX_DUAL | SPI_TX_QUAD;
ctlr->dev.of_node = np;
+ ctlr->auto_runtime_pm = true;
ret = devm_spi_register_controller(&pdev->dev, ctlr);
if (ret) {
@@ -1194,9 +1198,13 @@ static int zynqmp_qspi_probe(struct platform_device *pdev)
goto clk_dis_all;
}
+ pm_runtime_mark_last_busy(&pdev->dev);
+ pm_runtime_put_autosuspend(&pdev->dev);
+
return 0;
clk_dis_all:
+ pm_runtime_put_sync(&pdev->dev);
pm_runtime_set_suspended(&pdev->dev);
pm_runtime_disable(&pdev->dev);
clk_disable_unprepare(xqspi->refclk);
