Re: [PATCH v4 7/7] mtd: spi-nor: macronix: Add Octal 8D-8D-8D supports for Macronix mx25uw51245g

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



> > > > 
> > > > +#define MXIC_CR2_DUMMY_SET_ADDR 0x300
> > > > +
> > > > +/* Fixup the dummy cycles to device and setup octa_dtr_enable() 
*/
> > > > +static void mx25uw51245g_post_sfdp_fixups(struct spi_nor *nor)
> > > > +{
> > > > +   struct spi_nor_flash_parameter *params = nor->params;
> > > > +   int ret;
> > > > +   u8 rdc, wdc;
> > > > +
> > > > +   ret = spi_nor_read_cr2(nor, MXIC_CR2_DUMMY_SET_ADDR, &rdc);
> > > > +   if (ret)
> > > > +      return;
> > > > +
> > > > +   /* Refer to dummy cycle and frequency table(MHz) */
> > > > +   switch (params->dummy_cycles) {
> > > > +   case 10:   /* 10 dummy cycles for 104 MHz */
> > > > +      wdc = 5;
> > > > +      break;
> > > > +   case 12:   /* 12 dummy cycles for 133 MHz */
> > > > +      wdc = 4;
> > > > +      break;
> > > > +   case 16:   /* 16 dummy cycles for 166 MHz */
> > > > +      wdc = 2;
> > > > +      break;
> > > > +   case 18:   /* 18 dummy cycles for 173 MHz */
> > > > +      wdc = 1;
> > > > +      break;
> > > > +   case 20:   /* 20 dummy cycles for 200 MHz */
> > > > +   default:
> > > > +      wdc = 0;
> > > > +   }
> > > 
> > > I don't get the point of this. You already know the fastest the 
> > > mx25uw51245g flash can run at. Why not just use the maximum dummy 
> > > cycles? SPI NOR doesn't know the speed the controller is running at 
so 
> > > the best it can do is use the maximum dummy cycles possible so it 
never 
> > > falls short. Sure, it will be _slightly_ less performance, but we 
will 
> > > be sure to read the correct data, which is much much more important.
> > 
> > In general, 200MHz needs 20 dummy cycles but some powerful device may 
only 
> > 
> > needs 18 dummy cycles or less.
> 
> Yes, but do different mx25uw51245g chips have different dummy cycle 
> requirements? Shouldn't all the chips with the same ID have same 
> performance?
> 

Same chip ID but different grade,
i.e., commercial or industrial grade. 

thanks & best regards,
Mason

CONFIDENTIALITY NOTE:

This e-mail and any attachments may contain confidential information 
and/or personal data, which is protected by applicable laws. Please be 
reminded that duplication, disclosure, distribution, or use of this e-mail 
(and/or its attachments) or any part thereof is prohibited. If you receive 
this e-mail in error, please notify us immediately and delete this mail as 
well as its attachment(s) from your system. In addition, please be 
informed that collection, processing, and/or use of personal data is 
prohibited unless expressly permitted by personal data protection laws. 
Thank you for your attention and cooperation.

Macronix International Co., Ltd.

=====================================================================



============================================================================

CONFIDENTIALITY NOTE:

This e-mail and any attachments may contain confidential information and/or personal data, which is protected by applicable laws. Please be reminded that duplication, disclosure, distribution, or use of this e-mail (and/or its attachments) or any part thereof is prohibited. If you receive this e-mail in error, please notify us immediately and delete this mail as well as its attachment(s) from your system. In addition, please be informed that collection, processing, and/or use of personal data is prohibited unless expressly permitted by personal data protection laws. Thank you for your attention and cooperation.

Macronix International Co., Ltd.

=====================================================================




[Index of Archives]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux