Re: [PATCH V5 4/7] spi: spi-geni-qcom: Add interconnect support

[Matthias Kaehlcke <mka@xxxxxxxxxxxx>]

On Fri, May 08, 2020 at 12:03:36PM +0530, Akash Asthana wrote:
> Get the interconnect paths for SPI based Serial Engine device
> and vote according to the current bus speed of the driver.
> 
> Signed-off-by: Akash Asthana <akashast@xxxxxxxxxxxxxx>
> ---
> Changes in V2:
>  - As per Bjorn's comment, removed se == NULL check from geni_spi_icc_get
>  - As per Bjorn's comment, removed code to set se->icc_path* to NULL in failure
>  - As per Bjorn's comment, introduced and using devm_of_icc_get API for getting
>    path handle
>  - As per Matthias comment, added error handling for icc_set_bw call
> 
> Changes in V3:
>  - As per Matthias's comment, use helper ICC function from geni-se driver.
> 
> Changes in V4:
>  - Move peak_bw guess as twice of avg_bw if nothing mentioned explicitly
>    to ICC core.
> 
> Changes in V5:
>  - Use icc_enable/disable in power on/off call.
>  - Save some non-zero avg/peak value to ICC core by calling geni_icc_set_bw
>    from probe so that when resume/icc_enable is called NOC are running at
>    some non-zero value. No need to call icc_disable after BW vote because
>    device will resume and suspend before probe return and will leave ICC in
>    disabled state.
> 
>  drivers/spi/spi-geni-qcom.c | 32 +++++++++++++++++++++++++++++++-
>  1 file changed, 31 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/spi/spi-geni-qcom.c b/drivers/spi/spi-geni-qcom.c
> index c397242..5dfa1fb 100644
> --- a/drivers/spi/spi-geni-qcom.c
> +++ b/drivers/spi/spi-geni-qcom.c
> @@ -234,6 +234,13 @@ static int setup_fifo_params(struct spi_device *spi_slv,
>  		return ret;
>  	}
>  
> +	/* Set BW quota for CPU as driver supports FIFO mode only. */
> +	geni_icc_bw_init(&se->icc_paths[CPU_TO_GENI],
> +				Bps_to_icc(mas->cur_speed_hz), 0);
> +	ret = geni_icc_set_bw(se);
> +	if (ret)
> +		return ret;
> +
>  	clk_sel = idx & CLK_SEL_MSK;
>  	m_clk_cfg = (div << CLK_DIV_SHFT) | SER_CLK_EN;
>  	spi_setup_word_len(mas, spi_slv->mode, spi_slv->bits_per_word);
> @@ -578,6 +585,19 @@ static int spi_geni_probe(struct platform_device *pdev)
>  	spin_lock_init(&mas->lock);
>  	pm_runtime_enable(dev);
>  
> +	ret = geni_icc_get(&mas->se, NULL);
> +	if (ret)
> +		goto spi_geni_probe_runtime_disable;
> +	/* Set the bus quota to a reasonable value for register access */
> +	geni_icc_bw_init(&mas->se.icc_paths[GENI_TO_CORE],
> +			Bps_to_icc(CORE_2X_50_MHZ), 0);
> +	geni_icc_bw_init(&mas->se.icc_paths[CPU_TO_GENI], GENI_DEFAULT_BW, 0);
> +
> +	/* Set BW for register access */

This comment doesn't add any value. Register access is mentioned a few lines
above and from the function name it's evident that it sets the ICC bandwidth.

> +	ret = geni_icc_set_bw(&mas->se);
> +	if (ret)
> +		goto spi_geni_probe_runtime_disable;
> +
>  	ret = spi_geni_init(mas);
>  	if (ret)
>  		goto spi_geni_probe_runtime_disable;
> @@ -616,14 +636,24 @@ static int __maybe_unused spi_geni_runtime_suspend(struct device *dev)
>  {
>  	struct spi_master *spi = dev_get_drvdata(dev);
>  	struct spi_geni_master *mas = spi_master_get_devdata(spi);
> +	int ret;
> +
> +	ret = geni_se_resources_off(&mas->se);
> +	if (ret)
> +		return ret;
>  
> -	return geni_se_resources_off(&mas->se);
> +	return geni_icc_disable(&mas->se);
>  }
>  
>  static int __maybe_unused spi_geni_runtime_resume(struct device *dev)
>  {
>  	struct spi_master *spi = dev_get_drvdata(dev);
>  	struct spi_geni_master *mas = spi_master_get_devdata(spi);
> +	int ret;
> +
> +	ret = geni_icc_enable(&mas->se);
> +	if (ret)
> +		return ret;
>  
>  	return geni_se_resources_on(&mas->se);
>  }

Reviewed-by: Matthias Kaehlcke <mka@xxxxxxxxxxxx>