Re: [PATCH 1/4] spi: lantiq: Synchronize interrupt handlers and transfers

[Hauke Mehrtens <hauke@xxxxxxxxxx>]

On 4/24/20 12:42 PM, Dilip Kota wrote:
> Synchronize tx, rx and error interrupts by registering to the
> same interrupt handler. Interrupt handler will recognize and process
> the appropriate interrupt on the basis of interrupt status register.
> Also, establish synchronization between the interrupt handler and
> transfer operation by taking the locks and registering the interrupt
> handler as thread IRQ which avoids the bottom half.
> Fixes the wrongly populated interrupt register offsets too.
> 
> Fixes: 17f84b793c01 ("spi: lantiq-ssc: add support for Lantiq SSC SPI controller")
> Fixes: ad2fca0721d1 ("spi: lantiq-ssc: add LTQ_ prefix to defines")
> Signed-off-by: Dilip Kota <eswara.kota@xxxxxxxxxxxxxxx>
> ---
>  drivers/spi/spi-lantiq-ssc.c | 89 ++++++++++++++++++++++----------------------
>  1 file changed, 45 insertions(+), 44 deletions(-)
> 

Hi,

I tried this patch series on a TP-LINK TD-W8970 (VRX200 with SPI flash)
and the SPI controller is failing like this:
-----
[    6.947194] printk: bootconsole [early0] disabled
[    6.964210] spi-lantiq-ssc 1e100800.spi: Lantiq SSC SPI controller
(Rev 8, TXFS 8, RXFS 8, DMA 1)
[    7.175188] spi-nor spi0.4: SPI transfer timed out
[    7.178558] spi_master spi0: failed to transfer one message from queue
[    7.185120] spi-nor spi0.4: error -145 reading JEDEC ID
[    7.190378] spi-nor: probe of spi0.4 failed with error -2
[    7.199729] libphy: Fixed MDIO Bus: probed
------
It already fails when applying this first patch only.


Without this patch is works like this:
-----
[    6.939498] printk: bootconsole [early0] disabled
[    6.954016] spi-lantiq-ssc 1e100800.spi: Lantiq SSC SPI controller
(Rev 8, TXFS 8, RXFS 8, DMA 1)
[    6.975465] spi-nor spi0.4: s25fl064k (8192 Kbytes)
[    6.979066] 4 fixed-partitions partitions found on MTD device spi0.4
[    6.985338] Creating 4 MTD partitions on "spi0.4":
[    6.990127] 0x000000000000-0x000000020000 : "u-boot"
[    6.997422] 0x000000020000-0x0000007c0000 : "firmware"
[    7.212304] random: crng init done
[    8.796128] 2 tplink-fw partitions found on MTD device firmware
[    8.800674] 0x000000020000-0x00000027878f : "kernel"
[    8.807776] 0x000000278790-0x0000007c0000 : "rootfs"
[    8.813611] mtd: device 3 (rootfs) set to be root filesystem
[    8.818268] 1 squashfs-split partitions found on MTD device rootfs
[    8.824123] 0x000000590000-0x0000007c0000 : "rootfs_data"
[    8.831772] 0x0000007c0000-0x0000007d0000 : "config"
[    8.837785] 0x0000007d0000-0x000000800000 : "boardconfig"
[    8.848193] libphy: Fixed MDIO Bus: probed
------

This was done by applying your patches on top of kernel 5.4.35 and
adding this: "spi: lantiq-ssc: Use devm_platform_ioremap_resource() in
lantiq_ssc_probe()" in OpenWrt master.

Hauke