Re: [PATCH 03/21] spi: spi-geni-qcom: Use OPP API to set clk/perf state

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 




On 4/9/2020 11:50 PM, Matthias Kaehlcke wrote:
Hi Rajendra,

On Wed, Apr 08, 2020 at 07:16:29PM +0530, Rajendra Nayak wrote:
geni spi needs to express a perforamnce state requirement on CX
depending on the frequency of the clock rates. Use OPP table from
DT to register with OPP framework and use dev_pm_opp_set_rate() to
set the clk/perf state.

Signed-off-by: Rajendra Nayak <rnayak@xxxxxxxxxxxxxx>
Cc: Alok Chauhan <alokc@xxxxxxxxxxxxxx>
Cc: Akash Asthana <akashast@xxxxxxxxxxxxxx>
Cc: linux-spi@xxxxxxxxxxxxxxx
---
  drivers/spi/spi-geni-qcom.c | 14 +++++++++++---
  1 file changed, 11 insertions(+), 3 deletions(-)

diff --git a/drivers/spi/spi-geni-qcom.c b/drivers/spi/spi-geni-qcom.c
index c397242..ce387dc 100644
--- a/drivers/spi/spi-geni-qcom.c
+++ b/drivers/spi/spi-geni-qcom.c
@@ -7,6 +7,7 @@
  #include <linux/log2.h>
  #include <linux/module.h>
  #include <linux/platform_device.h>
+#include <linux/pm_opp.h>
  #include <linux/pm_runtime.h>
  #include <linux/qcom-geni-se.h>
  #include <linux/spi/spi.h>
@@ -95,7 +96,6 @@ static int get_spi_clk_cfg(unsigned int speed_hz,
  {
  	unsigned long sclk_freq;
  	unsigned int actual_hz;
-	struct geni_se *se = &mas->se;
  	int ret;
ret = geni_se_clk_freq_match(&mas->se,
@@ -112,9 +112,9 @@ static int get_spi_clk_cfg(unsigned int speed_hz,
dev_dbg(mas->dev, "req %u=>%u sclk %lu, idx %d, div %d\n", speed_hz,
  				actual_hz, sclk_freq, *clk_idx, *clk_div);
-	ret = clk_set_rate(se->clk, sclk_freq);
+	ret = dev_pm_opp_set_rate(mas->dev, sclk_freq);
  	if (ret)
-		dev_err(mas->dev, "clk_set_rate failed %d\n", ret);
+		dev_err(mas->dev, "dev_pm_opp_set_rate failed %d\n", ret);
  	return ret;
  }
@@ -553,6 +553,7 @@ static int spi_geni_probe(struct platform_device *pdev)
  	if (!spi)
  		return -ENOMEM;
+
  	platform_set_drvdata(pdev, spi);
  	mas = spi_master_get_devdata(spi);
  	mas->irq = irq;
@@ -561,6 +562,8 @@ static int spi_geni_probe(struct platform_device *pdev)
  	mas->se.wrapper = dev_get_drvdata(dev->parent);
  	mas->se.base = base;
  	mas->se.clk = clk;
+	mas->se.opp = dev_pm_opp_set_clkname(&pdev->dev, "se");

As commented on the serial patch, it seems an error check is needed
and the OPP table saved in 'struct geni_se' is never used.

right, I explained about the OPP table in the other patch.


+	dev_pm_opp_of_add_table(&pdev->dev);

This function could also fail for multiple reasons, so the return value
should be checked.

 From patch "[01/21] opp: Manage empty OPP tables with clk handle" it seems
ignoring errors is intended to be able to operate when no OPP table is
specified. But even with that you want to return in case of certain errors,
like an invalid OPP table, out of memory or -EPROBE_DEFER.

Thats correct, my intention of not checking the errors was in cases where its
optional, and I did not want to break anything with existing DT. I will go back and
check if its indeed possible for it to return a -EPROBE_DEFER and others which
I should handle.

--
QUALCOMM INDIA, on behalf of Qualcomm Innovation Center, Inc. is a member
of Code Aurora Forum, hosted by The Linux Foundation



[Index of Archives]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux