RE: [PATCH v5 11/15] dmaengine: imx-sdma: fix ecspi1 rx dma not work on i.mx8mm

[Robin Gong <yibin.gong@xxxxxxx>]

On 2020/02/06 Schrempf Frieder <frieder.schrempf@xxxxxxxxxx> wrote:
> 
> Hi,
> On 27.09.19 03:55, Robin Gong wrote:
> > On 2019-9-25 22:53 Schrempf Frieder <frieder.schrempf@xxxxxxxxxx> wrote:
> >> On 25.09.19 13:26, Robin Gong wrote:
> >>> On 2019-9-24 21:28 Schrempf Frieder <frieder.schrempf@xxxxxxxxxx>
> >> wrote:
> >>>>
> >>>> Hi Robin,
> >>>>
> >>>>> From: Robin Gong <yibin.gong at nxp.com>
> >>>>>
> >>>>> Because the number of ecspi1 rx event on i.mx8mm is 0, the
> >>>>> condition check ignore such special case without dma channel
> >>>>> enabled, which caused
> >>>>> ecspi1 rx works failed. Actually, no need to check
> >>>>> event_id0/event_id1 and replace checking 'event_id1' with
> >>>>> 'DMA_DEV_TO_DEV', so that configure
> >>>>> event_id1 only in case DEV_TO_DEV.
> >>>>>
> >>>>> Signed-off-by: Robin Gong <yibin.gong at nxp.com>
> >>>>> Acked-by: Vinod Koul <vkoul at kernel.org>
> >>>>
> >>>> I have a custom board with i.MX8MM and SPI flash on ecspi1. I'm
> >>>> currently testing with v5.3 and as SPI didn't work, I tried two
> >>>> different
> >> things:
> >>>>
> >>>> 1. Removing 'dmas' and 'dma-names' from the ecspi1 node in
> >> imx8mm.dtsi,
> >>>>       to use PIO instead of DMA. This works as expected and the driver
> >>>>       boots with the following messages:
> >>>>
> >>>>           spi_imx 30820000.spi: dma setup error -19, use pio
> >>>>           m25p80 spi0.0: mx25v8035f (1024 Kbytes)
> >>>>           spi_imx 30820000.spi: probed
> >>>>
> >>>> 2. Applying your patchset and use DMA. In this case, the flash also
> >>>>       works fine, but there are some error messages printed while
> >> booting:
> >>>>
> >>>>           spi_master spi0: I/O Error in DMA RX
> >>>>           m25p80 spi0.0: SPI transfer failed: -110
> >>>>           spi_master spi0: failed to transfer one message from queue
> >>>>           m25p80 spi0.0: mx25v8035f (1024 Kbytes)
> >>>>           spi_imx 30820000.spi: probed
> >>>>
> >>>> It would be great to get your patches merged and fix SPI + DMA, but
> >>>> for i.MX8MM, we need to get rid of the error messages. Do you have
> >>>> an idea, what's wrong?
> >>
> >>> Could you check if the length of spi message is bigger than
> >>> fifo_size during spi_nor probe? If yes, at that time maybe sdma firmware
> not loaded.
> >>> if (transfer->len < spi_imx->devtype_data->fifo_size)
> >>
> >> Indeed, most of the transfers triggered by the SPI NOR dirver are
> >> below fifo_size and work fine, but some are bigger. The transfers
> >> therefore try to use DMA, but the firmware is not loaded yet.
> >>
> >> How is this supposed to work? Shouldn't all transfers use PIO as long
> >> as the SDMA firmware is not loaded yet?
> > Yes, for ecspi should work with ram script, it's better check if sdma
> > firmware is ready in spi_imx_dma_configure(), need modification in sdma
> driver too.
> > I'll create another patch after this patch set accepted.
> 
> This still seems to be broken upstream. Is anyone working on fixing SPI
> + DMA for i.MX8MM? Otherwise I will send a patch that removes the DMA
> from the ecspi nodes in the devicetree.
Sorry, Frieder, my patch set has been blocked for so long time because I revert
some patches and need get commit from patch owner, unfortunately, I didn't
get any feedback from them although I got ACK from maintainer. I'll pick up
them, rebase and resend it these days, then could address your issue later.