Re: [PATCH v3 1/2] dt-bindings: spi: Add schema for Cadence QSPI Controller driver

[Vignesh Raghavendra <vigneshr@xxxxxx>]

Hi,

On 09/12/19 2:10 pm, Ramuthevar,Vadivel MuruganX wrote:
> From: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@xxxxxxxxxxxxxxx>
> 
> Add dt-bindings documentation for Cadence-QSPI controller to support
> spi based flash memories.
> 
> Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@xxxxxxxxxxxxxxx>
> ---
>  .../devicetree/bindings/spi/cadence,qspi.yaml      | 162 +++++++++++++++++++++
>  1 file changed, 162 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/spi/cadence,qspi.yaml
> 
> diff --git a/Documentation/devicetree/bindings/spi/cadence,qspi.yaml b/Documentation/devicetree/bindings/spi/cadence,qspi.yaml
> new file mode 100644
> index 000000000000..7756c34bb453
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/spi/cadence,qspi.yaml
> @@ -0,0 +1,162 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: "http://devicetree.org/schemas/spi/cadence,qspi.yaml#";
> +$schema: "http://devicetree.org/meta-schemas/core.yaml#";
> +
> +title: Cadence QSPI Flash Controller support
> +
> +maintainers:
> +  - Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@xxxxxxxxxxxxxxx>
> +
> +allOf:
> +  - $ref: "spi-controller.yaml#"
> +
> +description: |
> +  Add support for the Cadence QSPI controller,This controller is
> +  present in the Intel LGM, Altera SoCFPGA and TI SoCs and this driver
> +  has been tested On Intel's LGM SoC.
> +

This looks like a commit message. Description should probably says
something like "Binding Documentation for Cadence QSPI controller..."

> +  - compatible : should be one of the following:
> +        Generic default - "cdns,qspi-nor".
> +        For TI 66AK2G SoC - "ti,k2g-qspi", "cdns,qspi-nor".
> +        For TI AM654 SoC  - "ti,am654-ospi", "cdns,qspi-nor".
> +        For Intel LGM SoC - "intel,lgm-qspi", "cdns,qspi-nor".
> +
> +properties:
> +  compatible:
> +    enum:

This should be:

  compatible:
    oneOf:
      - items:
        - enum:
           - ti,k2g-qspi
        - const: cdns,qspi-nor

      - items:
        - enum:
           - ti,am654-ospi
        - const: cdns,qspi-nor

      - items:
        - enum:
           - intel,lgm-qspi
        - const: cdns,qspi-nor

      - items:
        - const: cdns,qspi-nor

> +      - cadence,qspi

This wrong and does not match what you is there in description above.
"cadence" is not a valid vendor prefix... It should be "cdns" as per
Documentation/devicetree/bindings/vendor-prefixes.yaml

Have you verified this yaml schema? I see bunch of errors for my platform

> +      - cdns,qspi-nor
> +      - ti,k2g-qspi
> +      - ti,am654-ospi
> +      - intel,lgm-qspi
> +
> +  reg:
> +    description: |
> +      Contains two entries, each of which is a tuple consisting of a
> +      Physical address and length. The first entry is the address and
> +      length of the controller register set. The second entry is the
> +      address and length of the QSPI Controller data area.

Don't you need to put a constraint here, like:

maxItems: 2

> +
> +  interrupts:
> +    description:
> +      Unit interrupt specifier for the controller interrupt.
> +

maxItems: 1??

> +  clocks:
> +    description:
> +      phandle to the Quad SPI clock.
> +

maxItems: 1??

> +  cdns,fifo-depth:
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    description:
> +      Size of the data FIFO in words.
> +
> +  cdns,fifo-width:
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    description:
> +      Bus width of the data FIFO in bytes.
> +
> +  cdns,trigger-address:
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    description:
> +      32-bit indirect AHB trigger address.
> +
> +  cdns,is-decoded-cs:
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    description:
> +      Flag to indicate whether decoder is used or not.
> +
> +  cdns,rclk-en:
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    description: |
> +      Flag to indicate that QSPI return clock is used to latch the read data
> +      rather than the QSPI clock. Make sure that QSPI return clock is populated
> +      on the board before using this property.
> +
> +  resets:
> +    minItems: 1
> +    maxItems: 2
> +
> +  reset-names:
> +    minItems: 1
> +    maxItems: 2
> +    items:
> +      - const: qspi
> +      - const: qspi-ocp
> +
> +# subnode's properties
> +patternProperties:
> +  "^.*@[0-9a-fA-F]+$":
> +    type: object
> +    description:
> +      flash device uses the subnodes below defined properties.
> +
> +  cdns,read-delay:
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    description:
> +      Delay for read capture logic, in clock cycles.
> +
> +  cdns,tshsl-ns:
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    description: |
> +      Delay in nanoseconds for the length that the master mode chip select
> +      outputs are de-asserted between transactions.
> +
> +  cdns,tsd2d-ns:
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    description: |
> +      Delay in nanoseconds between one chip select being de-activated
> +      and the activation of another.
> +
> +  cdns,tchsh-ns:
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    description: |
> +      Delay in nanoseconds between last bit of current transaction and
> +      deasserting the device chip select (qspi_n_ss_out).
> +
> +  cdns,tslch-ns:
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    description: |
> +      Delay in nanoseconds between setting qspi_n_ss_out low and
> +      first bit transfer.
> +
> +required:
> +  - compatible
> +  - reg
> +  - interrupts
> +  - clocks

> +  - cdns,is-decoded-cs

Not a required property as per existing DT bindings


> +  - cdns,fifo-depth
> +  - cdns,fifo-width
> +  - cdns,trigger-address


> +  - resets
> +  - reset-names

Again optional properties

> +
> +examples:
> +  - |
> +    qspi: spi@ff705000 {
> +          compatible = "cadence,qspi", "cdns,qspi-nor";
> +          #address-cells = <1>;
> +          #size-cells = <0>;
> +          reg = <0xff705000 0x1000>,
> +                <0xffa00000 0x1000>;
> +          interrupts = <0 151 4>;
> +          clocks = <&qspi_clk>;
> +          cdns,is-decoded-cs;
> +          cdns,fifo-depth = <128>;
> +          cdns,fifo-width = <4>;
> +          cdns,trigger-address = <0x00000000>;
> +          resets = <&rst QSPI_RESET>, <&rst QSPI_OCP_RESET>;
> +          reset-names = "qspi", "qspi-ocp";
> +
> +          flash0: n25q00@0 {
> +              ...
> +              cdns,read-delay = <4>;
> +              cdns,tshsl-ns = <50>;
> +              cdns,tsd2d-ns = <50>;
> +              cdns,tchsh-ns = <4>;
> +              cdns,tslch-ns = <4>;
> +          };
> +    };
> +
> 

No blank line before EOF, please

-- 
Regards
Vignesh