Re: [PATCH v11 3/3] dt-bindings: mfd: Document Renesas R-Car Gen3 RPC-IF MFD bindings

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hello!

On 04/22/2019 06:32 AM, Mason Yang wrote:

> Document the bindings used by the Renesas R-Car Gen3 RPC-IF MFD.
> 
> Signed-off-by: Mason Yang <masonccyang@xxxxxxxxxxx>
> ---
>  .../devicetree/bindings/mfd/mfd-renesas-rpc.txt    | 39 ++++++++++++++++++++++
>  1 file changed, 39 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/mfd/mfd-renesas-rpc.txt
> 
> diff --git a/Documentation/devicetree/bindings/mfd/mfd-renesas-rpc.txt b/Documentation/devicetree/bindings/mfd/mfd-renesas-rpc.txt
> new file mode 100644
> index 0000000..ee3bad8
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/mfd-renesas-rpc.txt
> @@ -0,0 +1,39 @@
> +Renesas R-Car Gen3 RPC-IF MFD controller Device Tree Bindings
> +-------------------------------------------------------------
> +
> +Required properties:
> +- compatible: should be an SoC-specific compatible value, followed by
> +		"renesas,rcar-gen3-rpc" as a fallback.
> +		supported SoC-specific values are:
> +		"renesas,r8a77995-rpc"	(R-Car D3)
> +- reg: should contain three register areas:
> +	first for the base address of rpc-if registers,

   RPC-IF.

> +	second for the direct mapping read mode and
> +	third for the write buffer area.
> +- reg-names: should contain "regs", "dirmap" and "wbuf"
> +- clocks: should contain 1 entries for the module's clock
> +- clock-names: should contain "rpc"
> +- #address-cells: should be 1
> +- #size-cells: should be 0
> +
> +Example:
> +
> +	rpc: rpc-if@ee200000 {
> +		compatible = "renesas,r8a77995-rpc", "renesas,rcar-gen3-rpc";
> +		reg = <0 0xee200000 0 0x200>, <0 0x08000000 0 0x4000000>;
> +		reg-names = "regs", "dirmap";

  You forgot to add back the "wbuf" entrees above.

> +		clocks = <&cpg CPG_MOD 917>;
> +		clock-names = "rpc";
> +		power-domains = <&sysc R8A77995_PD_ALWAYS_ON>;
> +		resets = <&cpg 917>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		flash@0 {
> +			compatible = "jedec,spi-nor";
> +			reg = <0>;
> +			spi-max-frequency = <40000000>;
> +			spi-tx-bus-width = <1>;
> +			spi-rx-bus-width = <1>;
> +		};
> +	};
> 

MBR, Sergei



[Index of Archives]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux