Re: [PATCH v9 2/3] spi: Add Renesas R-Car Gen3 RPC-IF SPI controller driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hello!

On 04/10/2019 11:01 AM, masonccyang@xxxxxxxxxxx wrote:

>> >> > +static ssize_t rpc_spi_mem_dirmap_write(struct spi_mem_dirmap_desc
>> > *desc,
>> >> > +               u64 offs, size_t len, const void *buf)
>> >> > +{
>> >> > +   struct rpc_spi *rpc =
>> >> > +         spi_controller_get_devdata(desc->mem->spi->controller);
>> >> > +   int ret;
>> >> > +
>> >> > +   if (offs + desc->info.offset + len > U32_MAX)
>> >> > +      return -EINVAL;
>> >> > +
>> >> > +   if (len > RPC_WBUF_SIZE)
>> >> > +      len = RPC_WBUF_SIZE;
>> >> > +
>> >> > +   ret = rpc_spi_set_freq(rpc, desc->mem->spi->max_speed_hz);
>> >> > +   if (ret)
>> >> > +      return ret;
>> >> > +
>> >> > +   rpc_spi_mem_set_prep_op_cfg(desc->mem->spi,
>> >> > +                &desc->info.op_tmpl, &offs, &len);
>> >> > +
>> >> > +   regmap_update_bits(rpc->regmap, RPC_CMNCR, RPC_CMNCR_MD,
>> > RPC_CMNCR_MD);
>> >> > +
>> >> > +   regmap_write(rpc->regmap, RPC_SMDRENR, 0);
>> >> > +
>> >> > +   regmap_update_bits(rpc->regmap, RPC_PHYCNT, RPC_PHYCNT_STRTIM(7) |
>> >> > +            RPC_PHYCNT_WBUF2 | RPC_PHYCNT_WBUF,
>> >> > +            RPC_PHYCNT_WBUF2 | RPC_PHYCNT_WBUF);
>> >> > +
>> >> > +   memcpy_toio(rpc->wbuf, buf, len);
>> >>
>> >>    Wait, doesn't the manual say that the whole 256-byte buffer should be
>> >> filled?
> 
> it could be less than 256 bytes, i.e., 128 bytes to rpc->wbuf !

   The gen3 manual 1.50 contradicts:

Note: This area should be accessed sequentially from the start address and transfer size
to the device is 256-byte unit. All Write Buffer area should be filled with transfer data
in every transfer. When accessing non-sequentially or at random, the operation is not
guaranteed. After Write Buffer Operation, this cache area must be cleared by DRCR.RCF bit.

>  I think that short chunks have to be written w/o WBUF (done,
>> > in fact,
>> >> by the HF driver).
>> >>
>> >
>> > From spi-nor.c layer always transfer 256 bytes data with page program
>> > command.
>>
>> Does that apply even for flashes with not-256-byte pages ?
>>
> 
> I think it needs to patch in case of nor->page_size = 512 bytes.

   What needs to patch what? :-)

> thanks & best regards,
> Mason

MBR, Sergei



[Index of Archives]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux