RE: [PATCH v5 1/5] spi: spi-mem: Add driver for NXP FlexSPI controller

[Yogesh Narayan Gaur <yogeshnarayan.gaur@xxxxxxx>]

Hi Boris,

> -----Original Message-----
> From: Boris Brezillon [mailto:boris.brezillon@xxxxxxxxxxx]
> Sent: Monday, December 10, 2018 4:20 PM
> To: Yogesh Narayan Gaur <yogeshnarayan.gaur@xxxxxxx>
> Cc: Schrempf Frieder <frieder.schrempf@xxxxxxxxxx>; linux-
> mtd@xxxxxxxxxxxxxxxxxxx; marek.vasut@xxxxxxxxx; broonie@xxxxxxxxxx; linux-
> spi@xxxxxxxxxxxxxxx; devicetree@xxxxxxxxxxxxxxx; robh@xxxxxxxxxx;
> mark.rutland@xxxxxxx; shawnguo@xxxxxxxxxx; linux-arm-
> kernel@xxxxxxxxxxxxxxxxxxx; computersforpeace@xxxxxxxxx; linux-
> kernel@xxxxxxxxxxxxxxx
> Subject: Re: [PATCH v5 1/5] spi: spi-mem: Add driver for NXP FlexSPI controller
> 
> On Mon, 10 Dec 2018 10:43:56 +0000
> Yogesh Narayan Gaur <yogeshnarayan.gaur@xxxxxxx> wrote:
> 
> > > > Thus, in LUT preparation we have assigned only the base address.
> > > > Now if I have assigned ahb_buf_size to FSPI_FLSHXXCR0 register
> > > > then for
> > > read/write data beyond limit of ahb_buf_size offset I get data corruption.
> > >
> > > Why would you do that? We have the ->adjust_op_size() exactly for
> > > this reason, so, if someone tries to do a spi_mem_op with
> > > data.nbytes > ahb_buf_size you should return an error.
> > >
> > Let me explain my implementation with example. If I have to write data of size
> 0x100 bytes at offset 0x1200 for CS1, I would program as below:
> > In func nxp_fspi_select_mem(), would set value of controller address space
> size, memmap_phy_size, to FSPI_FLSHA2CR0 and rest all FSPI_FLSHXXCR0 as 0.
> > Value of memmap_phy_size is 0x10000000 i.e. 256 MB for my LX2160ARDB
> target.
> > Then in nxp_fspi_prepare_lut(), I would prepare LUT ADDR with address length
> requirement 3/4 byte for NOR or 1/2/3/4 bytes for NAND flash.
> > Also for LUT_NXP_WRITE would program data bytes as 0.
> >
> > Then inside func nxp_fspi_do_op(), set register FSPI_IPCR0 as the
> > address offset i.e. 0x1200 and in register FSPI_IPCR1 program the data
> > size to write i.e. 0x100
> >
> > If, as suggested if I tries to mark value of register FSPI_FLSHA2CR0 equal to
> ahb_buf_size (0x800), then access for address 0x1200 gives me wrong data. This
> is because as per the controller specification access to flash connected at CS1
> can be performed under range of FSPI_ FLSHA1CR0 and FSPI_ FLSHA2CR0.
> 
> Don't you have a way to set an offset to apply to the address accessed through
> the AHB? And if you don't, how will it work if your mapping is smaller than the
> flash size?

Write operations are triggered using IP commands instead of AHB command.
For Read AHB command is used and in this we are adding the offset when performing memcpy_fromIO operation
      memcpy_fromio(op->data.buf.in, (f->ahb_addr + op->addr.val), len);

AHB/IP operations are independent of the way how CS got selected. CS selection depends, e.g. CS1 on the value of register FSPI_FLSHA1CR0 and FSPI_FLSHA2CR0.

Mapping can never going to be smaller than the connected flash size as per discussion with the Board design team and if it's possible by user manually changes the non-soldered part then flash area beyond complete mapping is not accessible.
On LX2160ARDB, with mapping of 256MB, for now we are having 4 flash devices connected with size as 64 MB. If user wants he can have only one single flash with flash size of 256MB.

--
Regards
Yogesh Gaur